TUBE & FITTING SQUARING MACHINE TFS TABLE OF CONTENTS SECTION I. STANDARD EQUIPMENT ..................1 SECTION II. SAFETY Safety Instructions .................... 2 SECTION III. CE DECLARATION OF CONFORMITY ..............6 SECTION IV. MACHINE SPECIFICATIONS ..................7 SECTION V. SET UP & OPERATING PROCEDURES ..............8 Head and Tool Disk Selection and Mounting Procedures ........10...
TUBE & FITTING SQUARING MACHINE TFS TFS STANDARD EQUIPMENT SECTION I • TFS with drive motor and cord • Required Operating Hand Tools • 1 Tool bit • Operating Instruction Manual • Storage Case • ** Head and Tool disk...
TUBE & FITTING SQUARING MACHINE TFS SAFETY INSTRUCTIONS SECTION II Read the Following thoroughly before proceeding Since 1883, EH Wachs has built a reputation for qual- ALWAYS WEAR PROTECTIVE EQUIPMENT: ity and a commitment to consumer satisfaction. In accor- WARNING...
Page 5
Seit 1883 hat EH Wachs seinen Ruf für Qualität und Zufriedenstellung seiner Kunden aufgebaut. Wachs übernimmt demgemäß die Depuis 1883, la société EH Wachs a bâti sa réputation sur la qualité de ses produits et son engagement à satisfaire la clientèle.
Page 6
INSTRUÇÕES DE SEGURANÇA TURVALLISUUSOHJEET Já desde 1883 que a EH Wachs tem vindo a criar uma reputação de qualidade e um compromisso de satisfação dos EH Wachs on tunnettu korkeasta laadusta ja tyytyväisistä asiakkaistaan jo vuodesta 1883. Wachs huolehtii myös siitä, että...
Page 7
ANVISNING I SIKKERHED Siden 1883 har EH Wachs haft ry for deres kvalitet og varetagelse af kundtilfredshed og vil også gøre vort bedste for at sikre, at vore maskiner benyttes på en sikker og forsvarlig måde. Vi har lavet en liste over påmindelser, der skal bidrage til at skabe det sikrest mulige arbejdsmiljø. Vi anbefaler, at sikkerhedsforanstaltningerne på...
TUBE & FITTING SQUARING MACHINE TFS SECTION III EC Declaration of Conformity Name and address of manufacturer (if different) E.H. Wachs Company 100 Shepard St. Wheeling, Il. 60090 USA Distributed in the EC by: Business address: We declare that the machine described below conforms with the EHSR of the machinery directive 89/...
TUBE & FITTING SQUARING MACHINE TFS TFS SPECIFICATIONS SECTION IV The TFS is a Portable Electric Tool for Square, Burr-Free End Preparation of Tubes, Tube Fit- tings, Elbows, Ferrules and Thin Wall Pipe. Prep 1/2" (12 mm) through 4½" (114 mm) O.D.
Page 10
TUBE & FITTING SQUARING MACHINE TFS SECTION V SET UP & OPERATING INSTRUCTIONS...
TUBE & FITTING SQUARING MACHINE TFS TFS SETUP & OPERATING PROCEDURES SECTION V A. Clamp Handle B. Feed Knob C. Base Stand D. Clamp Head Assembly 2.5”/4.5” Clamp Head. Metabo Model (PN 20-031-00) Milwaukee Model (PN 18-015-00) SPEED RANGE SELECTOR- Dial in chosen motor 1.
TUBE & FITTING SQUARING MACHINE TFS TFS SETUP & OPERATING PROCEDURES (CONT.) SECTION V Head and Tool Disc Selection & Mounting Shoe Selection & Installation Select size of head and disc. Select shoe set by referencing selection chart. Small Head Large Head ½"...
TFS Drive Motors Place work into vise. ( Do not damage tool bit if it is installed.) Motors for TFS: Milwaukee and Metabo. Milwaukee has variable speed trigger. The Metabo has variable speed trigger with lock on, dial speed control; electronic load sensing.
Increasing feed and reducing speed will solve this problem. Figure 8 TFS bench stand can be removed. Loosen two FHCS on stand base plate. To reinstall, place stand off tube on drive system. Stack base plate on top. Install two FHCS ( Figure 8 ).
TUBE & FITTING SQUARING MACHINE TFS TFS TROUBLE SHOOTING SECTION VIII Trouble Possible Cause Remedy Machine Won't Run ......Power Unit Not Connected ......Check Power Cord & Connection Work Piece Shifts Under....Loose Shoe Clamp ......... Check Tension on Shoe Clamp Handle Cutting Load Poor Workpiece End Quality ....
TFS ORDERING INFORMATION SECTION X To place an order or to get more detailed information on any E.H. Wachs products, call us at: 1-800-323-8185. ORDERING REPLACEMENT PARTS Please use parts list provided in manual. Have part description and part number of required replacement part or parts to help expedite order and insure proper parts are being ordered.