Page 1
PROOF S4 Montage- und Bedienungsanleitung Montage- und Bedienungsanleitung Assembly and operating instructions Installation and operating instructions...
Page 2
Reinigungs- oder Desinfektionsmittel verwenden nur mit weichem Schwamm oder Tuch behandeln keine Reinigung mit Dampfstrahlgeräten Diese Anleitung ist gültig für folgende Produkte: WimTec PROOF S4 - 12 V Edelstahl Art.Nr. 119 718 Chrom Art.Nr. 119 701...
PROOF S4 Technische Daten Betriebsspannung: WimTec UP Netzteil 230 V 50 Hz / 12 V= Leistungsaufnahme: max. 3 W Magnetventil: Kartusche 6 V Nah-Ansprechbereich: ca. 3 cm Spülstoppzeit: 10 s bis 1 min einstellbar Fließdruck: 0,05 bis 0,5 MPa (0,5 bis 5 bar) Thermostat: mit Heißwassersperre (38 °C)
R 1/2“ IG R 1/2“ IG Dicht- manschette min 95 max 120 Spannungsversorgung: WimTec Versorgungskabel (3 m) Ab Klemmdose: 2 x 0,5 mm max. 100 m Gesamt-Kabellänge Achtung: Netzteil nicht im Rohbauset oder eventuellen Schutzbereichen anbringen. WimTec PROOF S4 Duschearmatur...
Sicherheitsspülstopp, regelung mit Taste zum Entriegeln 30 s voreingestellt der 38 °C Sicherheitssperre. (10 s bis 60 s einstellbar). Generell gilt für alle Regler: Gegen den Uhrzeiger- sinn zum Reduzieren. Im Uhrzeigersinn zum Erhöhen. WimTec PROOF S4 Duschearmatur...
PROOF S4 Rohbauset 12 V= Abgang Kopfbrause Schmutzsieb und Rückflussverhinderer Magnetventil für Kopfbrause Fixierschraube zum Anschluss des Thermostat mit Adapter Kabels für den Potentialausgleichs Absperrventil bei Auslieferung geschlossen WimTec PROOF S4 Duschearmatur...
Vorstehenden Teil des Rohbaukastens fliesenbündig Folgende Schritte unbe- abschneiden. dingt in beschriebener Reihenfolge ausführen! Ggf. zwischen Wand und Rohbauset mit Silikon abdichten. 4. Wasserzuleitung absperren. Beide Vorabsperrungen mit einem Schraubendreher öffnen. Adapter für Thermostat mit Inbus 2,5 montieren. WimTec PROOF S4 Duschearmatur...
Page 9
Magnetventil anstecken und dann Elektro-Anschluss am Elektronikmodul herstellen. Thermostatposition kontrollieren (Thermostatwelle auf linken Anschlag drehen, dann nach rechts bis Pfeil nach oben zeigt). Danach Spannungsversorgung einschalten (Sicherheits- schließimpuls des Magnetventils erfolgt). Beigelegtes Spezialfett an der Dichtung vorne auftragen. WimTec PROOF S4 Duschearmatur...
Page 10
Position des Thermostatknopfes kontrollieren - Absperrknopf zeigt senkrecht nach oben. Frontplatte schräg aufsetzen und mit Druck in die waagrechte Position nach links drehen. Frontplatte mit Sicherungsschraube rechts unten sichern. Wasserleitung öffnen. Gerät ist nun betriebsbereit. Funktionstest durchführen. WimTec PROOF S4 Duschearmatur...
PROOF S4 Funktion Wasserfluss startet Wasserfluss stoppt Sobald der Benutzer auf Nach Ablauf der den Taster tippt. eingestellten Laufzeit (siehe Seite 6). 10 s - 60 s WimTec PROOF S4 Duschearmatur...
Page 14
PROOF S4 General notes Congratulations on purchasing the WimTec PROOF S4. In order to ensure that you will be able to enjoy this high-quality product for many years, please take note of the following cleaning and maintenance recommendations: Use mild cleaning agents containing soap...
Page 15
Technical data ................ 16 Dimensions ................17 Legend ..................18 Front plate ................18 Control elements ..............18 Flush-mount set ..............19 Assembly ................20 Function .................. 23 Replacement parts flush-mount set ........24 Replacement parts shower fitting .......... 25 WimTec PROOF S4 Shower control...
PROOF S4 Technical data Operating voltage: WimTec UP power supply 230 V 50 Hz / 12 V= Power consumption: max. 3 W Magnetic valve: cartridge 6 V Close detection range: approx. 3 cm Flushing time: 10 s - 1 min adjustable...
95 max 120 Power supply: WimTec supply cable (3 m) From terminal box: 2 x 0,5 mm max. 100 m total cable length Attention: Do not mount power unit in panel or security sectors. Control wire for thermal disinfection: 2 x 0,5 mm max.
30 min preset bypassing the 38 °C safety lock. (10 s to 60 s adjustable). The general rule applies to all controls: Move counterclockwise to decrease the setting. Move clockwise to increase the setting. WimTec PROOF S4 Shower control...
PROOF S4 Flush-mount set 12 V= outlet rain shower Dirt filter and return flow valve Magnetic valve for rain shower Fixing screw, for connection Thermostat with adapter of potential equalisation Cut-off valve (closed upon delivery) WimTec PROOF S4 Shower control...
Where necessary, seal off space between wall and flush- mount set with silicone. 4. Close the main water valve. Open both integrated stop valves using a screwdriver. Mount adapter for thermostat using the 2.5 Allen key. WimTec PROOF S4 Shower control...
Page 21
Switch on the power supply (causing the safety locking mechanism of the magnetic valve to activate). Apply the included special grease to the front of the valve. WimTec PROOF S4 Shower control...
Page 22
Arrest front plate by fastening the locking screw at the lower right. Open the main water valve. The device is now ready for operation. Perform a system test. WimTec PROOF S4 Shower control...
PROOF S4 Function Water flow starts Water flow stops As soon as you tap the After the configured button. flow time has elapsed (see page 18). 10 s - 60 s WimTec PROOF S4 Shower control...