GİRİŞ Değerli İFYIL Dostu; İFYIL TERMO İKLİMLENDİRME SAN. Ve TİC. LTD. ŞTİ. Fabrikasında titiz çalışmalar sonucu sizlere en verimli ürünleri sunmayı arzuluyoruz. Bunun için, bu kılavuzun tamamını, ürününüzü kullanmadan önce dikkatle okumanızı ve bir kullanım kolaylığı olarak saklamanızı önemle rica ederiz. Bilgilendirme Bu sembol, sobanın doğru kullanımında önemli detayları...
1. ÖNEMLİ UYARILAR 1.1. Genel Güvenlik Uyarıları • Ürün kullanılmadan önce kullanma kılavuzu dikkatlice okunmalıdır. • Ürün kullanılacağı ülkenin mevzuatlarına uygun olarak kurulum yapılmalı, gerekli emniyet tedbirleri alınmalıdır. Aksi halde İFYIL hiçbir sorumluluk kabul etmeyecektir • Bu bir pelet sobasıdır. Lütfen yakıt olarak odun peleti kullanınız. •...
1.2. Çalıştırma Uyarıları • İFYIL Pelet soba ve şömine sistemlerinin montajları; elektrik bağlantıları ve kurulum şemasına uygun olarak yapılmalıdır. • Pelet sobaları ev, ofis ve iç mekân için uygundur. Pelet sobaları balkon, depo, banyo vs. gibi alanlara kurulmamalıdır. Lütfen ev içi kullanımda mutfak, salon, antre gibi yerlerde;...
• Yakıtın kuru olup olmadığı kontrol edilmelidir. Yakıt nemli olmamalıdır. • Peletler yanma potasına elle atılmamalıdır. • Ateşleme düzgün gerçekleşmemişse soba kapatılıp pota temizlenmelidir. • Sobanın içi su ile yıkanmamalıdır. • Baca borusunda yangın varsa, sobayı kapatın ve yetkili mercilere başvurunuz. •...
Page 9
Teknik Data Ölçülen Değerler Cihaz Tipi / Modeli ; Pelet Sobası EFES GEDİZ Nominal ısı çıkışı Kapasite Minimum ısı çıkışı Nominal ısı çıkışı Verim Minimum ısı çıkışı Ø 6 / L:30 Odun Ø 6 / L:30 Odun Yakıt tipi Peleti Peleti Yakıt tüketimi (Min.- Maks.) kg/h...
3. YAKIT ÖZELLİKLERİ Odun peleti, kuru odun tozlarının sıcaklık yardımıyla sıkıştırılması ile oluşur. Materyalin kompakt oluşu ağacın kendi özünden gelir ve pelette yapışkan ya da tutkal kullanılmasına gerek kalmaz. Odun çeşitlerine ve karışımlarına bağlı olarak pelet çeşitlilik gösterir. ENplus-A1+A2 kaliteye sahip odun pelet yakıtı kullanılmalıdır. Tanımlar ENplus-A1 ENplus-A2...
4. KURULUM • Bu ürün ev içi ve iç mekân kullanımına uygundur. Lütfen ev içi kullanımda mutfak, salon, antre gibi yerlerde; iç mekân kullanımında kafeterya, restoran, işyeri gibi yerlerde kullanınız. • Balkon, banyo, depo gibi alanlara pelet sobası kurulmamalıdır. İç mekân haricindeki kullanım durumunda, ısınma ile ilgili sorunlarda firmamız sorumluluk kabul etmemektedir.
• Sobanın hava emiş borusu sürekli temiz hava akışı olabilecek bir ortama (Dış ortama) hermetik boru ile bağlanması önerilmektedir. • 300 cm² alt, 200 cm² üst menfez kullanılmalıdır. Bu menfezler asla kapatılmamalıdır. Aksi halde büyük tehlike oluşturur. • Sobanın kurulduğu alana temiz hava girişini sağlayan hava kanalları varsa bakım ve temizliği yapılmalıdır.
önlemek için baca başlığı kullanılmalıdır. • Beton bloklar sıcaklık değişiminden etkilendiği için, beton olan dairenin çatısı hava ile doğrudan temas halinde ise mutlaka yalıtılmalıdır. • Baca temizleme kapağı baca borusunun altında olmalıdır, baca temizliği buradan yapılmalıdır. • Duman çıkışı için doğru ve yeterli bir baca sistemi (herhangi bir elektrik kesintisi durumunda sobanızın içerisindeki dumanı...
4.6. Uygun Baca Şekilleri ve Bağlantıları Soba bacasının ev dışında kalan kısmı mutlaka izolasyonlu olmalıdır. Eğer bu izolasyonlar yapılmaz ise bacanın çekimi düştüğü için soba yanışında sorunlar meydana gelecektir. Sobanızın herhangi bir elektrik kesintisi durumunda içerisindeki dumanı dışarı atabilecek nitelikte doğal çekişe sahip bir baca uygulaması...
Page 16
** Uygun ve uygun olmayan baca şekilleri resimlerinde gösterilen sobalar temsilidir. YUKARIDAKİ ESASLARA UYMAYAN DAİRELERDE VE İŞ YERLERİNDE KIŞIN HER AN YANGIN ÇIKABİLİR VE KARBONMONOKSİT (CO) GAZI SIZINTISI YAŞANABİLİR. LÜTFEN YUKARIDAKİ ESASLARA UYALIM! OLUŞABİLECEK DURUMLARDA FİRMANIN HERHANGİ HUKUKİ VE CEZAİ MESULİYETİNİN OLMADIĞINI MÜŞTERİ...
5. ÇALIŞTIRMA 5.1. İlk Ateşleme • Pelet besleyici, her ilk ateşlemede pelet tankının içi tam dolu olamayabileceği için pelet tankından, pelet besleyiciye peletlerin düştüğünden emin olun. • Eğer birkaç yanma denemesinden sonra başarılı olunamıyorsa, pelet yanma potasının doğru konumlandırıldığından emin olunuz. •...
6. YAKIT KALİBRASYONU Cihazı devreye alma işleminde ve kullanılan peletin değiştirilme durumunda kalibrasyon işlemi gerçekleştirilmelidir. İlk kalibrasyon işlemi (kurulum) teknik servis tarafından yapılmak zorundadır. Kalibrasyon işlemi kazan soğuk ve çalışmıyor iken yapılmalıdır. Kalibrasyon işlemine başlamadan önce peletin düşüm noktasına peleti tartabileceğiniz bir kap yerleştiriniz.
Page 19
Kullanıcı kalibrasyon işlemi dahilinde bu iki parametre dışında hiçbir parametreyi değiştirmemelidir. Aksi durumda oluşabilecek performans kaybından kullanıcı sorumludur. Tüm bu işlemlerin servis tarafından yapılması tavsiye edilir. Model: Efes/Gediz Gr/10 dk P05 T03...
7. KONTROL PANELİ Ana ekranda görüntülenen değerler: Görüntü D1 : zaman, sistem durumu, hatalar, Menu, altmenu, parameter değeri Görüntü D2 : güç, parameter kodu Görüntü D4 : Ana sıcaklık, parametre kodu Fonksiyon Tuş Bir kere basıldığında Uzun basıldığında Bilgilendirmeler / Menüden çıkış Ateşleme / Söndürme / Hata giderme Sıcaklık değiştirme (+) / Değer artırma Pelet yükleme düzeltmesi...
7.1. Ekranda Görüntülenen Durum Açıklamaları Durum Durum Durum Ateşleme-Değişken Kapalı On 4 Güvenlik ateşleme Kontrol ChEc Stabilizasyon On 5 Söndürme Ateşleme-Ön On 1 Çalışma modu Blok Isıtma Ateşleme-Ön Ateşleme On 2 Modülasyon yükleme kurtarma Ateşleme-Sabit On 3 Bekleme Stby ateşleme 7.2.
Page 22
Pelet bitti hatası Er18 Pota temizleme motor hatası Er25 Servis hatası SErU Tanımlama İlk sistemin kendi kendini kontrol ettiği durumda problarda problem olduğunda Sond görünür. Bu mesaj sobanın temizlenme zamanının geldiğini ifade eder. Eğer soba ateşleme esnasında harici bir cihaz tarafından kapatılırsa ( Ön Yükleme evresinden sonra ) OFF dEL mesajı...
7.3. Kullanıcı Ekranı 1 Yanma Güç P3 tuşuna basınız: D2 kısmı yanıp sönecektir. Tekrar aynı tuşa Ayarı basıldığında değerler değişecektir. 5 saniye sonra yeni değer aktif olacak ve seçilen değeri görebilirsiniz. Manuel P3 tuşuna uzun basıldığında manuel pelet yükleme aktif olacaktır Pelet ve yakıt besleme sürekli olarak çalışacaktır.
7.4. Kullanıcı ekranı 2 Bu menüye erişebilmek için P3 ve P4 tuşlarına aynı anda basınız. Bu menu ısıtma fan gücünün değiştirilmesine izin verir. Isıtma fan gücü (Air) Bu menu ısıtma arka fan gücünün değiştirilmesine izin verir. Isıtma arka fan gücü (CAn) Bu menu oda termostatını...
Page 25
Ekranda ProG yazısı belirir. 3 adet altmenüden oluşur, Her bir program yöntemi: Günlük : Haftanın her günü için ayrı ayrı 3 adet program yazılabilir. Haftalık : Haftanın bütün günleri için yazılan program geçerli olur Haftasonu : Pazartesi-Cuma ya da Cumartesi-Pazar için 3 program ayarlanabilir.
Page 26
4) Ateşleme zamanını seçiniz 5) Değişiklik moduna girmek için P3 düğmesine basın: seçilen değer (saat veya dakika) yanıp söner. Değeri 0 1 . 0 0 değiştirmek için P3 tuşuna saat ve dakika arasında geçiş yapın, P2 / P4 ile arttırıp azaltılabilir. 6) P3 tuşuna basarak kaydediniz 2 1 .
Oda Termostatı (Efes) Anakart üzerinde bulunan 24-25 numaralı girişlerde (IN 3) köprü kaldırılarak, yerine Oda Termostatı bağlanabilir. 9.2 On/Off Model: Efes/Gediz...
10. BAKIM VE TEMİZLİK Sobanızın tüm temizlik işlemlerini, sobanız yanmıyor iken (soğuk halde iken) ve elektrik bağlantısı kesilmiş konumda yapınız.
Page 35
Türbülatör – Duman Boruları Temizliği; Türbülatör temizliğinde 1 numaralı kapağı (şekil 9-3) kapalı olmalıdır. – Şekil 9.1’de görülen 1 numaralı üst kapağı çıkarınız. – Şekilde 9.1’de görülen 2 ve 3 numaralı türbülatör kollarını aşağı ve yukarı doğru – hareket ettiriniz. Türbülatörler iyice temizlenene kadar devam ettiriniz.
11. SORUNLAR, NEDENLERİ VE ÇÖZÜMLERİ PROBLEMLER MUHTEMEL NEDENLER ÇÖZÜMLER 1. Elektrik soketi ve ana şalterin çalışır 1. Elektrik arıza veya voltaj eksikliği Soba çalışmıyor. konumda olduğundan emin olun, takılı 2. Sigorta atmış. olup olmadığını kontrol ediniz. 2. Sigortayı değiştiriniz. 1. Pelet haznesini doldurunuz. 1.
Page 37
arayınız. 1. Açma/ kapama düğmesine basılı tutarak sobanın kendini kontrol Soba alarm veriyor. 1. Soba bir problem algıladı. etmesini sağlayınız. Hata giderilirse soba kapanma durumuna geçer. Peletler yanma potasına yığılmakta, 1. Yetersiz yanma havası gelmektedir. 1. Odanın sürekli temiz hava ile kapak camı...
12. VERİMLİ KULLANMA İÇİN ÖNEMLİ TALİMATLAR • Sobayı ateşleme konumuna getirmeden önce küllüğün ve yanma potasının temiz ve yerine doğru yerleştirilmiş olduğundan emin olunuz. • Temizleme fırçası ile sobanızın iç kısmını temizleyiniz, dışını ise temiz bir bez yardımı ile temizleyiniz. •...
Page 41
MAIN PARTS AND DIMENSIONS............63 CONNECTION SCHEMAS..............67 9.1. Mainboard ................... 67 9.1.1. Model: Crystal ............... 67 9.1.2. Model: Thermal ..............68 On / Off ..................69 10. MAINTENANCE and CLEANING ............70 11. PROBLEMS, CAUSES and SOLUTIONS........... 72 12. SIGNIFICIANT INSTRUCTIONS for EFFECTIVE USING ......74 13.
INTRODUCTION Dear Friend of İFYIL; We, İFYIL TERMO İKLİMLENDİRME SAN. Ve TİC. LTD. ŞTİ. manufacture the most efficient hydro pellet stoves with utmost care for our distinguished customers. Please read this user guide carefully before starting to use our stove and keep it as a reference in any case.
• The product should be installed in accordance with the legislation of the country in which it will be used and the necessary safety precautions should be taken. Otherwise IFYIL will not accept any responsibility. • This is a pellets stove. Please only use wood pellets as fuel.
1.2. Operating Warnings Assembly of İFYIL pellet stoves and fireplaces; Electrical connections and • installation should be done in accordance with the scheme. Pellets stoves are for houses, office and internal places. • Pellets stoves must not be used in: Balcony, warehouse, bathroom etc. •...
Customers not obeying the above requirements and schemas cannot claim any right for any problem. In any case, contact your dealer or IFYIL. 2. TECHNICAL SPECIFICATIONS • This device should be installed in accordance with the related regulation and EU standards.
3. PELLETS Wood pellets are manufactured by hot-extruding compressed sawdust which is produced during the working of natural dried wood. The compactness of the material comes from the lignin which is contained in the wood itself, and allows the production of pellets without the use of glues or binders. Depending on the wood varieties and mixtures, the pellet varies.
4. INSTALLATION • This stoves product for houses, offices and internal places. • Pellet stove should not be installed in areas such as balconies, bathrooms, warehouses. In case of use outside of the interior, our company accepts no responsibility for the problems related to heating. •...
If the stove is installed next to flammable wall, isolation for the wall should be done. • If the base where the stove is to be installed is made of flammable materials. If the stove is put on flammable material, suitable isolation must be done. •...
• Avoid installing the unit in the same environment with the following; o B type gas heaters or exhaust fan or fan less hoods o Collective ventilation pipes. o Aspirator device running in the same environment, can cause problems. 4.4. Chimney Instructions ➢...
• Chimney cap should be used to prevent the flow into the chimney flue repercussions of windy weather and rain. • Concrete blocks are affected by temperature changes, concrete flat roof which is in direct contact with the air must be absolutely isolated. •...
4.6. Suitable Shapes Of Chimney The remaining section of the chimney outside the home, it must be insulated. The smoke in the event of an electrical failure of your stove with a natural drive capable throw out the chimney must be applied. Figure 3- Suitable chimney shapes Figure 4- Improper chimney shapes Chimney required isolation must be performed.
Page 53
**stoves shown in Suitable and unsuitable chimney shapes pictures are representation. HOUSES AND OFFICES NOT OBEYING THE ABOVE MENTIONED STANDARDS ARE POTENTIAL FOR FIRE AT ANYTIME AND CARBON MONOXIDE (CO) GAS LEAKAGE. PLEASE FOLLOW THE ABOVE MENTIONED INSTRUCTİONS! BY SO, CLIENT ACCEPTS IN ADVANCE THAT IN SUCH CASES MANUFACTURER DOESN’T HAVE ANY RESPONSIBILTIES CLIENT NOT FULFILLING ABOVE MENTIONED REQUIREMENTS IN SCHEMAS CANNOT CLAIM ANY RIGHT OR COMPENSATION.
5. OPERATING 5.1. First Fire • The pellets feeder, not provide the required number of pellets in the tank is not full every first firing. So, the pellets tank, make sure that the pellets fall into the pellet’s feeder. • If not successful after several test burn, make sure of the correct positioning of the combustion pot.
6. FUEL CALIBRATION Calibration should be carried out during commissioning of the products and in case of replacement of the pellet used. The first calibration process (installation) must be performed by the service. Calibration procedure should be done when the boiler is cold and not working. Before starting the calibration process, place a bowl where you can weigh the pellet at the drop point of the pellet.
Page 56
The user must not change any parameters except these two parameters within the calibration process. Otherwise, the user is responsible for the loss of efficiency. It is recommended that all these operations be performed by the service. Model : Crystal/Thermal Gr/10 min P05 T03...
7. CONTROL PANEL Values displayed on the main screen: Image D1: time, system status, errors, Menu, submenu, parameter value Image D2: power, parameter code Image D4: Main temperature, parameter code Function Once it is pressed Long pressing Notifications/exit Menu Ignition / Extinguishing / Block reset Temperature change (+)/ihcrease Pellet loading correction value...
7.1 Status Descriptions Displayed on the Screen Status Code Status Code Status Code Ignition-Variable Close On 4 Safety ignition Control ChEc Stabilization On 5 Extinguishing Ignition-Preheating On 1 Working mode Block Ignition Ignition-Preload On 2 Modulation recovery Ignition-Fixed On 3 Waiting Stby ignition...
Page 59
Pellet out error Er18 Crucible cleaning engine failure Er25 Service error SErU Definition Code When the first system is in self-control, probes appear when there is a Sond problem. This message means that it is time to clean the stove. If the stove is switched off by an external device during the ignition (after the Pre-installation phase), the OFF dEL message is displayed.
7.3 User Screen 1 Combustion Press the P3 key: D2 will flash. Pressing the same key again Power Setting will change the values. After 5 seconds the new value will be active and you can see the selected value. Manual Pellet A long press on the P3 key will activate the manual pellet Loading loading and the fuel feed will run continuously.
7.4 User Screen 2 Press P3 and P4 at the same time to access this menu. Heating This menu allows the heating fan power to be changed. power (Air) Heating back fan This menu allows the heating back fan power to be changed. power (CAn) Room...
Page 62
ProG appears on the display. It consists of 3 subunits, each program method: Daily: 3 programs can be written separately for each day of the week. Weekly: The program for all days of the week is valid Weekend: 3 programs can be set for Monday-Friday or Saturday-Sunday. visualization Display Daily method: Day...
Page 63
5) Press the P3 button to enter the change mode: the selected value (hour or minute) blink. To change the 0 1 . 0 0 value, change the P3 key between hours and minutes and increase / decrease with P2 / P4. 6) Save by pressing P3 2 1 .
Room Thermostat (Crystal) The bridge located on inputs 24-25 on the motherboard (IN 3) can be removed and the room thermostat can be connected instead. 9.2 On / Off Model: Crystal/Thermal...
10. MAINTENANCE and CLEANING All cleaning of your stove, while your stove is not lit (when cold case) and make the electrical connection closed position. Şekil 9-1 Şekil 9-2 Şekil 9-3...
Page 72
Turbulator Cleaning; 1. For turbulator cleaning, the cover A (figure 9-3) must be closed. 2.Open the top cover (1), and you will see the turbulator rods. Move the turbulator rods up and down. Again, the moves until the turbulators are cleaned (Figure 9.1).
11. PROBLEMS, CAUSES and SOLUTIONS PROBLEM POSSIBLE CAUSE SOLUTIONS Stove does not work. Electrical failure or lack of power Make sure that the main switch in supply work position The fuse has blown. Change this fuse The pellets feeder is empty. Fill the pellets tank.
Page 74
The pellets are fed The pellets feeder is empty. Drain and refill the pellets tank. into the combustion Pellets feeder screw Sawdust pellets feeder manually chamber or not that (powder) to recover comes less. Sawdust (powder) was blocked from obstructions such as screws. Motor defective.
12. SIGNIFICIANT INSTRUCTIONS for EFFECTIVE USING • Please, clean the ash before ignition the stove. • Please clean the inside of the glazed models with the help of cleaner and outside with the clean cloth. • The insulated environment is recommended to use the stove. •...
Any right cannot be claimed due to the changes or modifications or wrong use of spare parts. IFYIL original spare parts must be used for any permitted change of spare part. *IFYIL reserves the right to make changes in the properties, design and materials of its products.
GARANTİ ŞARTLARI Garanti süresi, malın teslim tarihinden itibaren başlar ve iki (2) yıldır. Malın cam ve döküm parçaları hariç olmak üzere tamamı garanti kapsamındadır. Malın ayıplı olduğunun anlaşılması durumunda tüketici, 6502 sayılı Tüketicinin Korunması Hakkında Kanunun 11 inci maddesinde yer alan; a- Sözleşmeden dönme, b- Satış...
Page 79
İçeriğinde mdf, suntalem gibi kimyasal maddeler olan pelet kullanılması halinde cihaz zarar görebileceğinden dolayı ürününüz garanti kapsamı dışına çıkar. Cihazın kurulumunun veya yapılacak herhangi bir değişikliğin yetkili kişi veya kurumlar (Teknik Servis, Bayi vs.) tarafından yapılmaması, cihazın garanti kapsamı dışında kalmasına neden olur.
WARRANTY CONDITIONS The warranty period starts from the delivery date of the product and is two (2) years. The product is fully in warranty, except for the glass and cast parts. In case the product is found to be defective, Article 11 of the Law No. 6502 on Consumer Protection;...
Page 82
Product will out of Warranty when installation/any change made by non authorised personnel or services. Warranty does not covers any damages due to set up ifyil pellet stoves in open air areas, wet places, humid places or any place which directly related to all these places.
Page 84
ısıtma sektöründe 20 ülkeye ihracatı ile dünya pazarında devam ettiriyor. İFYIL TERMO İklimlendirme San. Ve Tic. Ltd. Şti. Kavak Organize Sanayi Bölgesi 3. Cad. No.11 Kavak / Samsun / Türkiye Tel : +90 362 266 9443 Fax : +90 362 266 9443 Mail : info@ifyil.com.tr www.ifyil.com.tr...