HoMedics enviraScape Gentle Rains WRF-GEN Instruction Manual And Warranty Information page 3

Assembly and Instructions for Use
Figure 1
1. Unpack the product and place on a horizontal
Minimum
surface. Wipe off dust with a damp cloth.
Water Level
2. Familiarize yourself with the pump. The pump
speed is controlled by the switch located at the
front of the pump. The speed is indicated by a "-"
and "+" (Fig 1). At its highest speed level, the
switch will cease to move any further. To decrease
the pump speed, move the switch upward toward
the "-"sign. Similarly, at its lowest speed, the
switch will cease to move any further.
Flow Control Valve
3. Insert the plastic tubing into the pump. Place
(+) faster water
pump into fountain lower basin (Fig 2).
output
4. Fill the lower basin with clean water. The water level
(-) slower water
should be approximately
output
net (Fig 3). NOTE: Distilled water is
recommended for easier maintenance.
5. Attach the A/C adaptor jack to the base power
cord. DO NOT plug into outlet at this time(Fig 2.)
6. Insert sound cord through hole in top basin and
insert into plug on bottom of lid. Then screw
housing clockwise until tight (Fig 4).
Figure 2
S S o o u u n n d d
S S e e l l e e c c t t i i o o n n
V V o o l l u u m m e e
C C o o n n t t r r o o l l
S S o o u u n n d d
C C o o r r d d
B B a a s s e e P P o o w w e e r r
O O n n / / O O f f f f S S w w i i t t c c h h
C C o o r r d d
1
/ an inch below the steel
2
M M u u s s i i c c S S p p e e a a k k e e r r
L L i i g g h h t t
S S w w i i t t c c h h
L L o o c c k k
P P l l a a s s t t i i c c T T u u b b i i n n g g
P P u u m m p p
L L o o w w e e r r B B a a s s i i n n
A A d d a a p p t t o o r r
B B A A C C K K V V I I E E W W
4
Figure 3
W W a a t t e e r r F F l l o o w w
D D i i a a l l
Figure 4
S S o o u u n n d d P P l l u u g g
L L E E D D ' ' s s
W W a a t t e e r r
F F l l o o w w
D D i i a a l l
C C l l e e a a n n i i n n g g
P P i i n n
L L o o c c k k s s
NOTE: Main power switch must be used to
turn unit completely on or off.
- Fountain can be used independent of
sound machine
- Sound Machine can be used without
fountain water flowing, although pump
will remain on unless main "on/off"
switch is turned off.
7. Tilt lid forward and line up the hooks
of the lid with the square locks of the
top basin. Then place flat onto
fountain top and slide lock switch
(Fig. 2) to hold securely in place.
8. Plug the power cord into a 120V
household outlet. The fountain &
sound machine are controlled by the
switch on the power cord. To operate
Rain Forest Fountain, turn on by
rotating switch on cord (Fig. 2). If
fountain doesn't operate, rotate switch
once to turn on and once more to turn
off to reset. NOTE: Unit power must
be "ON" in order for both the fountain
and sound machine to operate.
9. To use light, flip switch on the back of
the fountain lid (Fig 2).
10. To adjust rainfall speed, turn the water
flow dial (Fig 3) clockwise to increase
the rainfall and counter-clockwise to
decrease. When dial stops in
counter-clockwise motion, rainfall will
come to a stop. For trickling water
wall effect leave dial in lowest position
before coming to a complete stop.
NOTE: If water is not flowing properly
down the rock wall run your finger
horizontaly across the wall to spread
the water.
11. To use sounds, turn volume dial
(Fig 2) counter-clockwise to turn on.
Then select your nature sound by
pressing the sound button of your
choice. Volume can be adjusted by
turning the volume dial – counter-
clockwise to increase volume and
clockwise to decrease volume.
12. To Turn sounds off either:
a. Press the off button on the lid to
retain your volume setting for the
next use, or
b. Turn the volume dial clockwise until
it clicks off.
13. Turn fountain & sound machine off by
turning the switch on the power cord.
5