Secufirst SEC24 SensorCam Quick Start Manual

QUICKSTARTGUIDE

KIT CONTENT

Adapter DC5V/1.5
Wireless SensorCam
x1
White-Light LED
HD Camera
StatusLED
Light Sensor
Motion Sensor
FCC Compliance Statement: This device complieswith Part
15of the FCCrules. Operation issubjected to the following
two conditions: (1)this device may not cause harmful
interference, and (2) this device must accept any
interferencereceived,including interference that may cause
undesiredoperation.
If the camera systemno longer functions or can no longer be repaired, it must be disposedof according to the valid statutory regulations.
Disposal of spentbatteries/accumulators:
You are requiredby law (Battery Ordinance) to return all spent batteriesand accumulators. Disposingof spentbatteries/accumulatorswith
commonhouseholdwaste is prohibited! Batteries/accumulators that contain hazardous substancesare markedwith the symbolson the
side.Thesesymbolsindicatethatitisprohibitedtodisposeofthesebatteries/accumulatorsinthehouseholdwaste.Theabbreviationsforthe
respective heavy metals are: Cd=cadmium,Hg=mercury,Pb=lead. You can return spent batteries and accumulators that can no longer be
charged to the designated collection points in your community, outlets or wherever batteries or accumulators are sold. Following these
instructionswill allow youtofulfill thelegal requirementsandcontributetotheprotection of ourenvironment!
QuickStart Guide
Battery (18650Type)
x1 x2
Stand Mounting(Bottom)
5VMicro USB Power Input
Stand Mounting(Rear)
Battery Compartment
(18650x2)
MemoryCard Slot
(Support up to 32GB)
Wake UpButton(Short Press)
Motion Alert On/OffSwitch(Long Press)
ToActivate Motion Alert: Long press for5sec until RedLED blink once
ToDeactivate Motion Alert: Longpressfor 5sec until Blue LEDblinkonce
Products with CE Marking comply with EMC Directive
(2014/30/EU); Low Voltage Directive (2014/35/EU); RED
(2014/53/EU); ROHS Directive (2011/65/EU) issued by the
Commission of the European Community.
with these directives implies conformity to the following
European Norms:
EMC:EN301489
LVD:EN60950
Radio: EN 300328
IMPORTANT
Please Notice Below Before YouSetup TheSensorCam:
-SensorCamsupportedcloud backup function, makesurethat you have Google Drive, orDropbox
account beforeusingthis function.
-After initial setup,charge the camera for 4to 6hoursbeforegoing completely wireless.Oncethe
camera have beenfully charged,youwill receivepushnotification.
-Download andinstall "OMGuard HD"app fromGooglePlay
x1
-Make sureyour device isconnecting to Wi-Fi network.
-For maximumperformance, pleaseonly useClass10rated SD card. Thecamera wonʼt work without
SD card inserted.
-Please makesureto unbindyour cloudstorage account beforetransferring ownership ofthe camera.
SETUP THESENSORCAM
A.MicroSDCard/BatteryInstallation
(A1) Follow the stepsbelow to insertthe memorycard.
1
Compliance
Removethe battery
compartment cover
(A2) Power onthe camera by inserting2pcs18650batteriesand connect the wires.LED status
will flash red/blue(continue to Section B -Wi-FiNetworkSetup). Make surethe battery cables are
firmly connectedto thecamera, orpressand hold theresetbutton until the statusLED statusflashes
red/blue.
TM
For iOS
2 3 4
Pushforward to Flip upthe cover Insertthe SDcard
unlockthe cover and closethe cover
orthe AppStore®.
For Android
5 6
Pushforward Pushforward
to lockthe cover to closethe cover