Table of Contents
Advertisement
Quick Links
Introduction
This cutting fluid kit is for the Model SB1029
Surface Grinding Machine. The system is
designed to pump water-soluble cutting fluid to
minimize grinding wheel wear, load-up, glazing,
and heat. Using cutting fluid helps maximize
the quality of workpiece results, especially on
materials that should not be ground dry.
Specifications
•
Motor .......................................................
•
Phase & Cycle ................. 3-Phase & 50/60 Hz
•
Voltage ............................................220V/440V
•
Current ..................................... 0.3/0.15 Amps
•
Pump Type ..................................................Jet
•
Pump Flow ........................................ 8.2 GPM
•
Cutting Fluid Type ......... Water-Soluble Only
•
Maximum Tank Capacity ...................... 9 Gal.
•
Net Weight ............................................. 73 lbs
•
Country of Origin ................................ Taiwan
If you need help with your new model
SB1044 Cutting Fluid Kit, contact us at:
PHONE: (360) 734-1540
FAX: (360) 676-1075
EMAIL: sales@southbendlathe.com
WARNING: No portion of this manual may be reproduced without written approval.
MODEL SB1044
CUTTING FLUID KIT
Instruction Sheet
PHONE: (360) 734-1540 •
BIOLOGICAL & POISON
HAZARD!
Use the correct personal
protection equipment
when handling cutting
fluid. Follow federal, state,
and fluid manufacturer
requirements for proper
disposal.
Copyright © December, 2010 by South Bend Lathe Co.
#CR13482 Printed in Taiwan
www.southbendlathe.com
Unpacking
This item was carefully packaged to prevent
damage during transport. If you discover any
damage, please immediately call Customer
Service at (360) 734-1540 for advice. You may
need to file a freight claim, so save the containers
and all packing materials for possible inspection
by the carrier or its agent.
⁄
HP
1
8
Inventory
Item:
•
Tank Assembly w/Pump ................................ 1
—Drain Hose 1
—Hose Clamp 1
—Delivery Hose
—Hose Clamp 1
—Flex Conduit Power Cord 9' ....................... 1
—Drain Adapter ............................................. 1
—Swivel Caster Wheels ................................. 4
•
Splash Guard ................................................. 1
—Button Head Cap Screw M6-1 x 10 ........... 4
—Front & Rear Splash Panel .................. 1 Ea
•
Coolant Trough .............................................. 1
Figure 1. Model SB1044.
⁄
" x 5' .................................... 1
3
4
⁄
" ........................................ 1
3
4
⁄
'' x 9' ................................. 1
1
2
⁄
'' ......................................... 1
3
4
Qty
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for South bend SB1044
Summary of Contents for South bend SB1044
-
Page 1: Specifications
Net Weight ... 73 lbs • Country of Origin ... Taiwan If you need help with your new model SB1044 Cutting Fluid Kit, contact us at: PHONE: (360) 734-1540 FAX: (360) 676-1075 EMAIL: sales@southbendlathe.com Copyright © December, 2010 by South Bend Lathe Co. -
Page 2: Installation
Route the pump power cord around the backside of the surface grinder, or fasten it up and away from the floor. Connect the SB1044 power cord to the surface grinder as outlined on the Model SB1029 Pump Connection Wiring Diagram on Page 7. -
Page 3: Operation
ON. Coolant Switch Figure 3. SB1029 control panel. Adjust the flow of cutting fluid for the type of flooding required. Note: Promptly clean any splashed cutting fluid from the floor to avoid a slipping hazard. Model SB1044... -
Page 4: Maintenance
Model SB1044 Maintenance When you replace the old cutting fluid, take the time to thoroughly clean out both sides of the tank. Make sure to dispose all old fluid according to local regulations. Cutting fluid is considered hazardous waste by the EPA. Follow all disposal and storage guidelines when changing and disposing of cutting fluid. -
Page 5: Troubleshooting
Disconnect machine from power, manually reset thermal relay, and slightly turn-up trip setting. 14. Test/replace transformer. 15. Test all legs for power, test field coil and replace if at fault. 16. Test for shorted windings, bad bearings and repair or replace. Model SB1044 Possible Solution... -
Page 6: Electrical Safety Instructions
Model SB1044 Electrical Safety Instructions These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines. Study this section carefully. If you see differences between your machine and what is shown in this section, call Technical Support at (360) 734-1540 for assistance BEFORE making any changes to the wiring on your machine. - Page 7 To Oil OPTIONAL Pump CONNECTION Motor Power Cord Model SB1044 If the pump motor runs in a counterclockwise direction as viewed through the motor shaft sight glass, disconnect machine from power and swap wire positions U1 and V1 on the terminal bar shown below.
-
Page 8: Parts Diagram
Model SB1044 Parts Diagram 17 9 Please Note: We included this parts breakdown for service purposes only. Not all parts may be available as individual items. Warranty This quality product is warranted by South Bend Lathe Company to the original buyer for one year from the date of purchase.
Need help?
Do you have a question about the SB1044 and is the answer not in the manual?
Questions and answers