Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Neo Pro PTA07
- Page 1 PTA07 Powder Spray Customer Product Manual Part Issued 12/10...
-
Page 2: Table Of Contents
Table of Contents Safety 1-1 ..........Introduction 1-1 . -
Page 3: Safety
Section 1 Safety Introduction Read and follow these safety instructions. Task- and equipment-specific warnings, cautions, and instructions are included in equipment documentation where appropriate. Make sure all equipment documentation, including these instructions, is accessible to all persons operating or servicing equipment. Qualified Personnel Equipment owners are responsible for making sure that Promaks equipment is installed, operated, and serviced by qualified personnel. -
Page 4: Fire Safety
Fire Safety To avoid a fire or explosion, follow these instructions. Do not smoke, weld, grind, or use open flames where flammable materials are being used or stored. Provide adequate ventilation to prevent dangerous concentrations of volatile materials or vapors. Refer to local codes or your material MSDS for guidance. -
Page 5: Action In The Event Of A Malfunction
Action in the Event of a Malfunction If a system or any equipment in a system malfunctions, shut off the system immediately and perform the following steps: Disconnect and lock out electrical power. Close pneumatic shutoff valves and relieve pressures. Identify the reason for the malfunction and correct it before restarting the equipment. -
Page 6: Description
Section 2 Description The Promaks Tribo PTAG07 automatic powder spray gun uses friction (the tribo effect) to electrostatically charge powder coating particles as they are forced through the spray gun by compressed air. The spray gun is used with a PTAU07 controller and powder pump. The gun mount is used with a -in. -
Page 7: Operation And Maintenance
Section 3 Operation and Maintenance WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. WARNING: All electrically conductive equipment in the spray area must be grounded. Ungrounded or poorly grounded equipment can store an electrostatic charge which can give personnel a severe shock or arc and cause a fire or explosion. -
Page 8: Daily Maintenance
Operation Use different sprayheads for different part shapes. Select the appropriate nozzle for the parts being coated. Pinpoint nozzles for penetration Eight-orifice nozzles for flat surfaces Cylindrical nozzles for general purpose coating Angle the nozzles to meet and follow the parts as they move through the booth. -
Page 9: Troubleshooting
Section 4 Troubleshooting WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. This section contains troubleshooting procedures. These procedures cover only the most common problems that you may encounter. If you cannot solve the problem with the information given here, contact your local Promaks representative for help. -
Page 11: Repair
Section 5 Repair WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. -
Page 12: Parts
Section 6 Parts PTAG07 Automatic Gun Item Part Description PT631225 EXTENSION Body PT631221 SLEEVE, wear,outlet, assembly, teflon PT940224 O-RING, silicone, 1.000*1.125*0.0063 in PT361222 SPRING, silicone, 1.25*1.50 in ********** SLEEVE,wear,outlet , teflon PT631220 RING, spacing PT631212 SLEEVE, wear,outlet, teflon PT940284 O-RING, silicone, 1.375*1.500*0.0063 in PT631224 DISTRIBUTOR, outlet, teflon PT631216 SLEEVE, wear, inner, teflon PT631210 RING, positioning... -
Page 13: Diffuser
DIFFUSER Item Part Description PT631271 DIFFUSER CONNECTOR,MALE,1/8-in NPTF x1/4-in PT630035 tube PT635007 NOZZLE,diffuser PT940117 O-RING, silicone,0.312*0.438*0.063 in PT635008 HOUSING, diffuser PT631275 CLAMP,hose,0.781-0.875 in PT940224 O-RING, silicone,1.00*1.125*0.063 in... -
Page 14: Injector
INJECTOR Item Part Description PT630034 INJECTOR COMPLETE PT630043 VENTING HOSE ADAPTER PT630025 O-RING, silicone, 1.000*1.125*0.0063 in PT630037 INJECTOR BODY PT630036 INJECTOR NOZZLE PT630035 CONNECTOR,male,1/8-in NPTF*1/4-in tube PT630038 INSERT SLEEVE PT630041 INSERT SLEEVE NUT... -
Page 15: Ptau07Control Module Electrical Parts
PTAU07 Control module Electrical Parts 1 GOLD SER ES Control module (complete) PTAU07 2 Fixed plug, with gasket (for Mains connection) PG200 409 3 Fuse holder - F1 PG200 131 4 Knurled grounding nut - M6 PG200 433 5 Grounding Nut PT512 244 6 Control Box Air Fitler PNM100131... - Page 16 PTAU07 Control module...
-
Page 17: Ptau07Control Module Pneumatic Parts
PTAU07 Control module Pneumatic parts 1 Screw coupling - ø 8 mm PNM100102 2 Screw connector - ø 8 mm …………… 3 Screw coupling - ø 6 mm PNM100105 4 Screw connector - ø 6 mm …………… 5 Solenoid valve (24 VAC - 3/8" B.S.P. thread) PG235 865 5.1 Solenoid valve coil - 24 VAC PG243 930... - Page 18 PTAU07 Control module...