Intel bay trail-i e3815 (single core) / intel bay trail-d j1900 (quad core) cpu, on board / socket ddr3l, 4 x intel i211at lan / usb / vga / hdmi all-in-one intel bay trail-i e3815 1.46 ghz / intel bay trail-d j1900 2.0ghz vga, hdmi, com, pcie mini card m
Hardware Notice Guide ...................... CHAPTER 1 GENERAL INFORMATION ................. 1-1 MAJOR FEATURE........................ 1-2 SPECIFICATION ........................1-3 INSTALLING THE SO-DIMM (FOR 3I380D-D90) ..............1-3-1.1 REMOVING THE SO-DIMM (FOR 3I380D-D90) ............1-4 DIRECTIONS FOR INSTALLING THE MINI CARD ............. 1-5 PACKING LIST (FOR 3I380D-D90) ..................
Page 3
3-14 SATA INTERFACE ........................3-15 MICROSD CARD INTERFACE (SOCKET PUSH-PUSH) (OPTION) .......... 3-16 MODULE SOCKET ........................3-17 SIM SOCKET ..........................3-18 SODIMM SOCKET (OPTION) ..................... 3-19 CONNECTOR WAFER OF COMPATIBLE BRAND AND PART NUMBER LIST ......CHAPTER 4 INTRODUCTION OF BIOS ..................4-1 ENTER SETUP ..........................
Page 4
5-8 HOW TO UPDATE AMI BIOS ......................APPENDIX A:POWER CONSUMPTION TEST .................. APPENDIX B:RESOLUTION LIST ....................... APPENDIX C: F75111N I C DIO DECICE .................... 1-1 IO DEVICE : F75111 UNDER WINDOWS ..................1-2 IO DEVICE : F75111 VB6 UNDER WINDOWS ................1-3 IO DEVICE : F75111 UNDER LINUX .....................
Page 5
Copyright This manual is copyrighted and all rights are reserved. It does not allow any non authorization in copied, photocopied, translated or reproduced to any electronic or machine readable form in whole or in part without prior written consent from the manufacturer.
Warning ! Battery Batteries on board are consumables. The life time of them are not guaranteed. 2. Fless solution with HDD The specifi cation & limitation of HDD should be considered carefully when the fanless solution is implemented. We will not give further notifi cation in case of changes of product information and manual.
Hardware Notice Guide 1. Before linking power supply with the motherboard, please attach DC-in adapter to the motherboard fi rst. Then plug the adapter power to AC outlet. Always shut down the computer normally before you move the system unit or remove the power supply from the motherboard.
Chapter-1 General Information The 3I380D is built to be an all-in-one networking control board. It’s designed to combines all necessary input and output interfaces, which make them to be ideal control board for thin client, fi rewall or server applications. 3I380D is the perfect platforms for whole range of small form factor, low-power devices.
1-1 Major Feature Intel Bay Trail-I E3815 1.46GHz / Intel Bay Trail-D J1900 2.0/2.42(Burst)GHz SOC Intel Bay Trail-I Integrated Graphics chipset: Bay Trail-I E3815 Graphics speed: 400MHz Bay Trail-D J1900 Graphics speed: 688MHz/854MHz(Turbo) 1 x DDR3L SO-DIMM socket or On board DDR3L SDRAM (max. 4GB) On board SSD 4/8/16/32 GB (option) Support 4 x 10/100/1000 Mbps LAN on Board (Intel I211AT LAN chipset for PCIe x 1 V2.1 interface)
1-3 Installing the SO-DIMM (for 3I380D-D90) 1. Align the SO-DIMM with the connector at a 45 degree angle. 2. Press the SO-DIMM into the connector until you hear a click.
Page 13
Notices: 1.The connectors are designed to ensure the correct insertion. If you feel resistance, check t h e connectors & golden fi nger direction, and realign the card. 2. Make sure the retaining clips (on two sides of the slot) lock onto the notches of the card fi...
1-3-1.1 Removing the SO-DIMM (for 3I380D-D90) 1. Release the SO-DIMM by pulling outward the two retaining clips and the SO-DIMM pops up slightly. 2. Lift the SO-DIMM out of its connector carefully.
1-4 Directions for installing the Mini Card 1. Unscrew the screw on the board 2. Plug in the Mini Card in a 45 angle 3. Gently push down the Mini Card and screw the screw back.
1-5 Packing List ( For 3I380D-D90) Material Code Description Detail Specifi cation Quantit 7G1901-1481001-0 MB-3I380D-D90-00-001 LF,3I380D-D90-00,Rev.:001 6G8006-2347-0100 LEX Product Driver DVD LF, Intel Baytrail Driver 6G5212-0601-0200 60W Power Adapter,12V/5A,2.5 LF,L Type,FSP060-DBAE1,FSP 6G8001-2191-0400 Manual LF,M/B,3I380D 6G6003-7330-0100 Power Cable LF,L=9cm,2.0 1*4/DC JK *The packing list above is for the users who purchase single motherboard.
1-5-1 Packing List ( For 3I380D-I12) Material Code Description Detail Specifi cation Quantit 7G1901-1480001-0 MB-3I380D-I12-00-001 LF,3I380D-I12-00,Rev.:001 6G8006-2347-0100 LEX Product Driver DVD LF, Intel Baytrail Driver 6G5212-0601-0200 60W Power Adapter,12V/5A,2.5 LF,L Type,FSP060-DBAE1,FSP 6G8001-2191-0400 Manual LF,M/B,3I380D 6G6003-7330-0100 Power Cable LF,L=9cm,2.0 1*4/DC JK *The packing list above is for the users who purchase single motherboard.
Chapter-2 Hardware Installation 2-1 Unpacking Precaution This chapter provides the information how to install the hardware of 3I380D Please follow section 1-5,1-5-1, 2-1 and 2-2 to check the delivery package and unpack carefully. Please follow the jumper setting procedure. NOTE! 1.
2-2 Unpacking checkup First of all, please follow all necessary steps of section 2-1 to protect 3I380D from electricity discharge. With reference to section 1-5,1-5-1 please check the delivery package again with following steps: 1. Unpack the 3I380D board and keep all packing material, manual and driver disc etc, do not dispose ! 2.
2-6 Install Memory This motherboard provides one 204-pin Small Outline Dual In-line Memory Module (SODIMM) socket for memory expansion available maximum to of 2GB/4GB/8GB DDR3L SDRAM. DDR3L clock supports: DDR3 1333/1066MT/S Valid Memory Confi gurations Total Memory DIMM1 System Accept or Not Max.
2-7 List of Jumpers JSB1: CMOS clear select JSC2: COM2 RS422/RS485 select (Option) 2-8 Jumper Setting Description A jumper is ON as a closed circuit with a plastic cap covering two pins. A jumper is OFF as an open circuit without the plastic cap. Some jumpers have three pins, labeled 1, 2, and 3.
2-9 CMOS Data Clear A battery must be used to retain the motherboard confi guration in CMOS RAM. Close Pin1 and pin 2 of JSB1 to store the CMOS data. To clear the CMOS,follow the procedures below: 1. Turn off the system and unplug teh AC power 2.
Chapter-3 Connection This chapter provides all necessary information of the peripheral's connections, switches and indicators. Always power off the board before you install the peripherals. 3-1 List of Connectors CPI1: DC-in 1x4pin(2.0mm) Red wafer connector CPI2 DC-in 1x2 pin(2.0mm) Red wafer connector CPI11 DC-in 2x4 pin(2.0mm) wafer connector (Option) BAT1...
3-2 DC power input CPI1: DC-IN Internal Connector (1x4pin 2.0mm Red wafer) PIN NO. Description PIN NO. Description +VAD_AC +VAD_AC Note: 1. DC in from adapter plug in CPI2: DC-IN Internal Connector (1x2 pin 2.0mm Red Wafer) PIN NO. Description +VAD_AC Note: DC in from adapter plug in CPI11: DC-IN Internal Connector (2x4 pin 2.0mm Wafer )(Option)
3-3 Battery Input BAT1: 3V Battery hold 2pin BAT1: Battery use Li 3V / 220mAh (CR2032) Note: 1. When board without Adaptor plug in,this board power RTC consumption about 2.7uA 2. If adaptor always plug in RTC power consumption about 0.1uA BAT1 3-4 DC Power output CPO1: +12V/+5V DC voltage output (1x4pin 2.00mm Black wafer)
3-9 Digital Input / Output (option) CIO1 DIO 0 ~ 3 (2x5pin 2.0mm wafer) PIN NO. Description PIN NO. Description DI-0 DO-3 DI-1 DO-2 DI-2 DO-1 DI-3 DO-0 Note: 1. DI pin default pull up 10KΩ to +5V 2. If use need isolate circuit to control external device 3.
CL11/CL21/CL31/CL41: LAN port Giga /100Mb( 2x4pin 2.0mm wafer) (Option) PIN NO. Description PIN NO. Description TD0-/TX+ TD2-/NC TD0+/TX- TD2+/RX- TD1-/RX+ TD3-/NC TD1+/NC TD3+/NC CL32/CL44 : LAN LED wafer (1x4pin 1.25mm wafer) (Option) PIN NO. Description +3.3V Speed 10M Speed 100M Speed 1000M 3-13 USB Interface CU1 / CU2 / CU3: USB1/2/3 ports ( USB Type A connector )
Page 40
CU5: USB3.0 only port (1x5pin 1.25mm wafer) (For CU001 use) PIN NO. Description USB3_TX+ USB3_TX- USB3_RX+ USB3_RX- Note: 1. If use CU5 must to use CU43 (4pin 1.25mm Wafer) CU43 / CU44: Internal USB ports (1x4pin 1.25mm wafer) PIN NO. Description USB DATA - USB DATA +...
3-14 SATA interface SATA1: SATA1 connector PIN NO. Description DATA TX+ DATA TX- SATA1 DATA RX- DATA RX+ Note: 1. SATA1 support SATA 2.0 spec update 3Gb/sec. 2. CPO1 provide SATA HDD power +12V, GND, +5V SSD use SATA port 2 channel Note: 1.
Chapter-4 Introduction of BIOS The BIOS is a program located in the Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gains control. The BIOS fi rst operates an auto-diagnostic test called POST (Power on Self Test) for all the necessary hardware, it detects the entire hardware devices and confi...
4-2 BIOS Menu Screen & Function Keys In the above BIOS Setup main menu of, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us fi rst see a short description of the function keys you may use here: Press ←→...
4-3 General Help Status Page Setup Menu/ Option Page Setup Menu Press F1 to pop up a help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc> 4-4 Menu Bars There are six menu bars on top of BIOS screen: Main...
4-5 Main Main menu screen includes some basic system information. Highlight the item and then use the <+> or <-> and numerical keyboard keys to select the value you want in each item. System Date Set the Date. Please use [Tab] to switch between data elements. System Time Set the Time.
4-6-4 Video Confi guration Logo & SCU Resolution 1024 x 768(Default) , 800 x 600 , 640 x480...
Page 57
PAVC The function is setting the display quality, The optional settings are: Disabled, LITE Mode(default), SERPENT Mode Aperture Size The optional settings are: 128MB, 256MB(default), 512MB. IGD - DVMT Pre-Allocated Use this item to select DVMT 5.0 pre-allocated (fi xed) graphics memory size used by the internal graphics device.
4-6-5 Thermal Confi guration Thermal Confi guration Parameters This Value controls the temperature of the ACPI Critical Trip Point, the point in which the OS will shutdown the system. Critical Trip point is the shutdown temperature, the default value is 110˚ The CPU frequency will auto reduce when cpu temperature arrived to passive Trip point.
4-6-6 SATA Confi guration SATA Controller Use this item to Enable or Disable SATA Device. The optional settings are: Enabled(default) or Disabled Chipset SATA Mode Determine how SATA controller(s) operate. The optional settings are: IDE Mode(default), AHCI Mode. SATA Speed Indicates the maximum speed the SATA controller can support.
SATA Port 1 Connected to an ODD Use this item to Enable or Disable SATA Port1 ODD function The optional settings are: Enabled(default) or Disable 4-6-7 Console Redirection Console Serial Redirect Use this item to enable or disable Console Redirection. The optional settings are: Enabled, Disabled(default).
Stop Bits The optional settings are: 1 Bit(default) , 2 Bits Flow Control The optional settings are: None(default) , RTS/CTS , XON/XOFF 4-6-8 ACPI Table/Fetures Control ACPI Table/Features Control Select ACPI sleep state the system will enter when the SUSPEND button is pressed. The optional settings: DSDT - ACPI S3 (Suspend to RAM), Enabled or Disabled(default) DSDT –...
4-7 Security Supervisor Password To set up an Supervisor password 1. Select Supervisor Password. The screen then pops up an Create New Password dialog. 2. Enter your desired password that is no less than 3 characters and no more than 10 characters. 3.
4-8 Power Wake on PME Determines the action taken when the system power is off and the PCI power management Enable wake up event occurs. The optional settings: Enabled, Disabled(default) Power Button Instant OFF(default) : The system will be turn off directly when push the power button. Delay 4 sec : The system will be turn off when push the power button for 4 sec.
4-9 Boot Boot type Select boot type for Dual type ,Legacy boot type or UEFI boot type, default is Dual boot type Quiet Boot The optional settings are: Enabled(default), Disabled. EFI / Legacy Device order Determine EFI device fi rst or legacy device fi rst. The optional settings: EFI device fi...
4-10 EXIT Exit Saving Changes This item allows user to reset the system after saving the changes. Save Change Without Exit This item allows user to saving the changes but doesn’t restart. Exit Discard Changes This item allows user restart the system but no saving the changes Load Optimal Default Use this item to restore the optimal default for all the setup options.
4-11 Device Manager Please press the key F10 when bootup to go into the Device Manager menu Serial Port 1/2 Confi guration Please refer section 4-11-1...
4-11-1 SIO FINTEK81801U Serial Port 1/2 Use this item to enable or disable serial port (COM1,COM2) The optional settings are: Enabled(default), Disabled. Serial Port 1 Base IO Address / Interrupt / Serial Mode Use this item to select an optimal setting for super IO device. The optional settings are: IO=3F8h;...
Page 70
Serial Mode RS232 driver(default) : When hardware select to RS232 or RS422 mode, please enter to RS232 driver. RS485 driver: When hardware select to RS485 mode, please enter to RS485 driver. It is the auto fl ow function for RS485. Power Failure This item specifi...
Chapter-5 DRIVER INSTALLATION There is a system installation DVD in the package. This DVD does not only include all the drivers you need but also some other free application programs and utility programs. In addition, this DVD also includes an auto detect software telling you which hardware is installed and which driver is needed so that your system can function properly.
5-1 INF Install Intel Baytrail Chipset Driver (example for WIN8 64bit) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Intel® Chipset Device Software" menu" screen, click "INF". screen, click "Next". 3. At the "License Agreement" screen, 4. At the "Readme File Information" screen, click "Yes"...
Page 74
6. Click "Finish" & restart computer. 5. Click "Next" NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 64/32-bit, X:\driver\INTEL\BAY\INF\WIN7\infi nst_autol.exe For Windows 8 / 8.1 32/64-bit X:\driver\INTEL\BAY\INF\WIN_8_64\infi nst_autol.exe...
5-2 VGA Install Intel Baytrail VGA Driver (example for WIN8 64bit) 1. At the"AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup Program menu"screen, click "VGA". screen, Click "Next". 3. At the "License Agreement" screen, 4. At the "Readme File Information" Click "Yes"...
Page 76
6. Click "Finish" to restart computer 5. At the "Setup Progress" screen, Click "Next". NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32-bit, X:\driver\INTEL\BAY\VGA\WIN_7_32\Setup.exe For Windows 7 64-bit X:\driver\INTEL\BAY\VGA\WIN_7_64\Setup.exe For Windows 8 / Windows 8.1 32-bit X:\ \driver\INTEL\BAY\VGA\WIN_8_32\Setup.exe For Windows 8 / Windows 8.1 64-bit X:\driver\INTEL\BAY\VGA\WIN_8_64\Setup.exe...
5-3 Serial IO Install Driver Baytrail Serial IO Driver (FOR Windows 7 only) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup Program menu" screen, click "Serial IO". screen, Click "Next". 3. At the "License Agreement" screen, 4.
Page 78
5. At the "Ready to install the program" screen, 6. Click "Finish" and restart computer Click "Install" NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32-bit, X:\driver\INTEL\BAY\SERIALIO\WIN7_32Bit.msi For Windows 7 64-bit X:\driver\INTEL\BAY\SERIALIO\Win7_64Bit.msi...
5-4 xHCI Install Intel USB 3.0 xHCI Driver (FOR Windows 7 only) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup Program menu" screen, click "xHCI". screen, Click "Next". 3. At the "License Agreement" screen, 4. At the "Readme File Information" screen, Click "Yes".
Page 80
6. Click "Finish" to restart computer 5. At the "Setup Progress" screen, Click "Next". NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32 / 64-bit, X:\driver\INTEL\BAY\XHCI\Driver_Installer\Setup.exe...
5-5 HD Audio Install High Defi nition Audio Driver (example for WIN8 64bit) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. Click" Next". menu", click "HD Audio" 3. Click "Finish" to restart computer NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32 / 64-bit, Windows 8/8.1 32 / 64-bit X:\driver\INTEL\BAY\SOUND\Win7_Win8_Win81_R273.exe...
5-6 MBI Install Intel MBI Driver (FOR Win 8/8.1 only) 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Welcome to the Setup Program menu", click "HD Audio". screen, Click "Next". 3. At the "License Agreement" screen, 4. At the "Setup Progress" screen, Click "Next". Click "Yes".
Page 83
5. Click "Finish" to restart computer NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 8/8.1 32 / 64-bit, X:\driver\INTEL\BAY\MBI\Setup.exe...
5-7 TXE Install Intel TXE driver 5-7-1 TXE Install for WIN8/WIN8.1 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Setup" screen, Click "Next". menu", click "TXE". 3. At the "License Agreement" screen, 4. Click "Next". Click "Yes".
Page 85
5. Click "Finish" & restart computer NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 8 32 / 64-bit, X:\driver\INTEL\BAY\TXE\WIN_8\SetupTXE.exe For Windows 8.1 32 / 64-bit, X:\driver\INTEL\BAY\TXE\WIN_8.1\SetupTXE.exe...
5-7-2 TXE Install for WIN7 Please install PXE Patch fi rst. 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Windows Update" screen, menu", click "TXE Patch". Click "Yes". 3. Click “Finish” & restart computer 4. At the "AUTOMATIC DRIVER INSTALLATION menu", click "TXE "...
Page 87
5. At the "TXE Setup" screen, Click "Next". 6. At the "License Agreement" screen, Click "Yes". 8. Click "Finish" & restart computer 7. Click "Next". NOTE: SYSTEM INSTALL will auto detect fi le path For Windows 7 32 / 64-bit, TXE Patch X:\driver\INTEL\BAY\TXE\WIN_7\kmdf-1.11-Win-6.1-x86.msu X:\driver\INTEL\BAY\TXE\WIN_7\kmdf-1.11-Win-6.1-x64.msu...
(Storage device could be USB FDD or USB pen drive.) STEP 2. Copy utility program to your bootable disc. You may download it from our website. STEP 3. Copy the latest BIOS for your LEX motherboard from our website to your bootable disc.
Appendix A: Power Consumption Test Condition Item Spec Atom E3815 1.46 Ghz Memory DDR3L 1066 2GB Operating System Windows 7 / SP1 Test Program 3D Mark 06 HDD 2.5" SATA Slim Type HDD mSATA 32GB Test Result for reference only ! Start up Operation Shut down...
Page 90
Condition Item Spec Celeron J1900 2 Ghz Memory DDR3L 1333 4GB Operating System Windows 7 / SP1 Test Program 3D Mark Vantage HDD 2.5" SATA Slim Type HDD mSATA 32GB Test Result for reference only ! Start up Operation Shut down Power off Maximum Maximum...
Appendix C: F75111N I C DIO device 1-1 IO Device: F75111 under Windows The Sample code source you can download from Source fi le: F75111_DIOSrc.rar http://tprd.info/lexwiki/index.php/IO_Device:F75111 Binary fi le: F75111_DemoBin.rar USERNAME & PASSWORD: sf How to use this Demo Application 1.
Page 93
p.s. f75111 send "F75111_SetWDTEnable(BYTE byteTimer)" including a parameter "timer", if there's no disable signal (F75111_SetWDTDisable()) to stop it before timer countdown to 0, System will reboot. if there's disable signal received, resent Enable WDT signal, for a loop to prevent from reboot Introduction Initial Internal F75111 port address (0x9c) defi...
Disable WatchDog void F75111_SetWDTDisable () WriteByte(F75111_INTERNAL_ADDR,WDT_CONFIGURATION,0x00); // Disable WatchDog 1-2 IO Device: F75111 VB6 under Windows The Sample code source you can download from Source fi le: 75111_VB_v10.rar http://tprd.info/lexwiki/index.php/IO_Device:F75111_VB6 Binary fi le: 75111_VB_Src.rar USERNAME & PASSWORD: sf How to use this Demo Application A Function - Enable WDT timer ,Key-in the value by seconds then system will reboot after value which you key-in in left text box !! B Function - Disable WDT timer ,Push down the button then WDT timer value will be clear !!
Page 96
SDK Function Introduction Function EnableWDT Function EnableWDT(timer As Integer) Call WriteI2CByte(&H3, &H3) Call WriteI2CByte(&H37, timer) Call WriteI2CByte(&H36, &H73) End Function Function DisableWDT Function DisableWDT() Call WriteI2CByte(&H36, &H0) End Function Function SetDOValue Function SetDOValue(dovalue As Integer) Call WriteI2CByte(&H23, &H0) Call WriteI2CByte(&H20, &HFF) Call WriteI2CByte(&H2B, &HFF) Call WriteI2CByte(&H21, dovalue) End Function...
1-3 IO Device: F75111 under linux The Sample code source you can download from Source fi le: F75111v2.0L.tar.gz http://tprd.info/lexwiki/index.php/IO_Device:F75111_under_linux Binary fi le: F75111v2.0LBin.tar.gz USERNAME & PASSWORD: sf How to compile source code 1. Compile source code with Code::Blocks download and install the Code::Block with command "apt-get install codeblocks" Open an exist project(F75111.cbp) in Code::Blocks, click the compile button ( add an option 'pkg-confi...
Page 98
1. Press the "Start" button to test DIO function 2. Press the "Enable" button to test WDT function 3. Press the "Disable" button to disable WDT 4. Check the "Enable Loop" box and press "Enable" to do WDT loop test 5.