Table of Contents
Advertisement
Quick Links
1M23Z05806
R334SBS/R334SBS-E Software update manual
can be downloaded from Futaba distributor's website.
*The screen can vary based on the PC.
Required for update (Purchase separately)
Preparations
1.
Install the driver for the CIU-3/CIU-2 onto your PC.
When the CIU-3 is first connected to the PC, download the recommended driver software. The "Found
New Hardware Wizard" window appears on the screen. Click "Locate and install driver software".
When the CIU-2 is first connected to the PC, the "Found New Hardware Wizard" window appears on the
screen. Install the drivers download from local Futaba distributor's Website.
Refer to the manual of the CIU-3/CIU-2 for further information.
- 1 -
CIU-3 or CIU-2
Advertisement
Table of Contents
Related Manuals for FUTABA R334SBS
Summary of Contents for FUTABA R334SBS
- Page 1 1M23Z05806 R334SBS/R334SBS-E Software update manual can be downloaded from Futaba distributor's website. *The screen can vary based on the PC. Required for update (Purchase separately) Preparations Install the driver for the CIU-3/CIU-2 onto your PC. CIU-3 or CIU-2 When the CIU-3 is first connected to the PC, download the recommended driver software. The "Found New Hardware Wizard" window appears on the screen. Click "Locate and install driver software". When the CIU-2 is first connected to the PC, the "Found New Hardware Wizard" window appears on the screen. Install the drivers download from local Futaba distributor's Website. Refer to the manual of the CIU-3/CIU-2 for further information. - 1 -...
- Page 2 Updating procedure Download the zip file of the update data from your local distributor's website. Futaba WEB site Software Download Extract the zip file on your computer. Update program Executable file *Put in the same folder. Connect as shown in the diagram. - 2 -...
- Page 3 Turn on the receiver power while pressing down the Link switch. 1.Hold down the Link switch first. 2.Next turn ON the receiver. Once the LED confirms by flashing red once, release the Link switch and press again. When you continue pushing the Link switch, the LED starts flashing red and green. (Once flashing Red and Green, the initial process is complete. ) Update ready Red and Green light. Start the PC update. (The receiver should keep red and green on.) Write R334SBS - 3 -...
- Page 4 Wait for about 2 minutes. Don't turn off the power ! Green steady light Completed R334SBS/R334SBS-E Turn off the power switch of your receiver and remove the CIU-3/CIU-2. Be sure to check each function before use. Error If an error display appears, replace an with the update from the beginning. ◆ The receiver is not in the update "ready". ◆ The cable is disconnected. ◆ The power has been turned off. - 4 -...
- Page 5 R334SBS/R334SBS-E SOFTWARE UPDATE CHANGES Version: 3.0 1. Compatible with Wireless MC970CR parameters setting function The operating parameters of the Futaba MC970CR connected to receiver can be set and changed from the transmitter wirelessly. *Transmitter (T7PX/T7XC) also needs to be updated to version 3.0. R334SBS/R334SBS-E SOFTWARE UPDATE CHANGES Version: 2.0 1. Compatible with Wireless S.BUS setting function The operating parameters of the Futaba programmable S.BUS2 servo connected to receiver can be set and changed from the transmitter wirelessly. *Transmitter (T7PX) also needs to be updated to version 2.0. *Please refer to the update manual of the T7PX transmitter (Ver.2.0) for how to use the wireless S.BUS setting.
Need help?
Do you have a question about the R334SBS and is the answer not in the manual?
Questions and answers