4- and 8-button keypad with rs-232 interface (23 pages)
Summary of Contents for Broadata Communications LB-KP8E-ICP
Page 1
8- AND 16-BUTTON WALL PLATE ETHERNET KEYPAD LB-KP8E-ICP / LB-KP16E-ICP USER MANUAL BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result of their use or application.
Page 2
This product contains sensitive electrical components that may be damaged by electrical spikes,surges,electric shock,lightning strikes, etc. Use of surge proctection system is highly recommended in order to protect and extend the life of your equipment. 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 3
Install this device in a secure location where it cannot be easily pushed or knocked over. Use of this device is not suitable for use within 6 ft. of a medical patient. 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
TABLE OF CONTENTS PRODUCT DESCRIPTION OPERATION CONTROL AND FUNCTIONS FRONT/REAR PANEL TELNET COMMANDS CONFIGURATION SPECIFICATIONS MAINTENANCE AND TROUBLESHOOTING SERVICE PROCEDURE REPLACEMENT POLICY RETURN AND REPAIR SERVICE LIMITED WARRANTY 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
• Available with PoE function or DC power supply selection • Supports Telnet or WebGUI control • Supports scheduling control and settings • Adjustable LED dim light in keypad buttons 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
PSE 48v it can be powered without DC supply connection. DC 5V: Plug the 5V DC power adaptor included in the package and connect to AC wall outlet for power supply. 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
MACRO N MACRO SETTING ID (1-16) MACRO STOP TELNET_TIMEOUTN SET TELNET TIMOUT ON/OFF N=ON/OFF NOTE: ANY COMMANDS WILL NOT BE EXECUTED UNLESS FOLLOWED BY A CARRIAGE RETURN. COMMANDS ARE CASE-SENSITIVE 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Commands are case-sensitive. If the IP is changed then the IP Address required for Telnet access will also change accordingly. CLIC EDIT SY EDIT C SETT DOWN 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP) ARE TO M COMMA...
Page 9
LIGHTING TOMIZE AND THEN RCENTAGE CLICK ON 8/16 ED ON THE BUTTON KEYPAD. AL ILLUMI- CK ON THE YMBOL TO COMMAND TINGS. UP/ N ARROWS 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP) MOVE THE AND UP OR...
Page 10
LED with 0% brightness, switch Off & On Relay 1 with delay of LEDS 1000ms. BASE To disable default testing mode, set Demo Mode switch to off. ORIGNIA 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 11
Click on the edit symbol to edit command settings. Up/down arrows are to move the command up or down and delete button is to delete the command. KGROUND R ALLOWS O INSTANT- ANGE THE LIGHTING RCENTAGE ED ON THE AL ILLUMI- 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 12
IP and Port number and it is strongly recommand to set the delay RO ACTIONS, time>500ms in order to secure a successful command sending. Once the setting is done click on Save change. 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 13
Save Change to confirm the setting. KGROUND R ALLOWS O INSTANT- ANGE THE Extension Macro LIGHTING Click on Extension Macro to execute/edit up to 8 more Macro actions, RCENTAGE ED ON THE AL ILLUMI- 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 14
512 characters including spaces) plus 96 commands (each command less than 128 characters including spaces) are supported. Click on Save Change to save the command. THE BACK LIGHT BAR USER TO LY CHA LEDS BASE ORIGNIA 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 15
O INSTANT- ANGE THE LIGHTING RCENTAGE Click on Edit to add a new device to be controlled. Enter the Device Name, IP Address and Connect Port. ED ON THE AL ILLUMI- 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 16
URE THE REPEAT OR TOGGLE SET- THE BACK LIGHT BAR USER TO TING OF A KEY. IF LY CHA LEDS REPEAT IS SET TO BASE ORIGNIA ON, PRESSING AND HOLDING THE KEY 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 17
O INSTANT- ANGE THE LIGHTING RCENTAGE Click on Edit from Repeat column to set the macro command(s) to be activated ED ON THE repeatedly on a set time. AL ILLUMI- 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 18
Click on Edit from Once column to set the macro command(s) to be activated on a set time only. THE BACK LIGHT BAR USER TO LY CHA LEDS BASE ORIGNIA 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 19
Macro settings. Reset to Default allows IP and login ID & RCENTAGE password to be reset back to factory default. ED ON THE AL ILLUMI- 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 20
Time(DST) function. Simply click on the white column and a calendar will appear for your selection with current timing setting. Another simple few clicks to enable/ disable DST with its start and end. THE BACK LIGHT BAR USER TO LY CHA LEDS BASE ORIGNIA 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 21
Switch. 4) Connect the Receiver (LBC-H/O-R-ICP) to the Transmitter (LBC-HDV-T-ICP). 5) Plug in the power for the LB-KP8E-ICP (not required if the switch supports PoE) 6) Plug in power for the LBC-H/O-R-ICP 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 22
BASE BUTTON KEYPAD. ORIGNIA At this point the IP address of the LB-KP8E-ICP is unknown and must be discovered using the BCI Product Configuration tool. Launch the BCI Product Configuration tool. In the list of discovered units, the LB-KP8E-ICP will appear as LB-KP8E.
Page 23
ICP’s IP address in the Network Keypad Address box. Click on the Submit Changes AL ILLUMI- button. The keypad status should change to Connected LB-KP8E, indicating that the LB-KP8E-ICP is connected to the LBC-H/O-R-ICP. 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 24
On the top menu bar, click on Keypad. The virtual 8 button keypad page shown below will be loaded. Each button on the virtual keypad represents a button on the LB-KP8E-ICP. By default buttons are unconfigured and labeled F1 to F8.
Page 25
In the Action Type drop down menu, select Relay. O INSTANT- In the Action drop down menu, select Relay 1 On. ANGE THE Click on Submit Changes button. LIGHTING RCENTAGE ED ON THE AL ILLUMI- 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 26
In the Action Type drop down menu, select Relay. In the Action drop down menu, select Relay 1 Off. Click on Submit Changes button. THE BACK LIGHT BAR USER TO LY CHA LEDS BASE ORIGNIA 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 27
Click on the Relay 1 On button to turn on Relay 1. Click on the Relay 1 Off button to turn off Relay 1. On the LB-KP8, pressing the F1 button should turn on Relay 1 and pressing the F2 button should turn off Relay 1. 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 28
In the Action Type drop down menu, select Relay. In the Action drop down menu, select Relay 2 On. THE BACK Click on Submit Changes button. LIGHT BAR USER TO LY CHA LEDS BASE ORIGNIA 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 29
R ALLOWS O INSTANT- ANGE THE LIGHTING RCENTAGE ED ON THE AL ILLUMI- To test the button, click on Keypad on the top menu bar. The following keypad should be shown. 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 30
In the RS-232 Channel drop down menu, select 1. ORIGNIA In the Transmit String box, type in serial string. Click the Submit Changes button. The RS-232 action, named RS-232 string, has been created. 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 31
In the Action Type drop down menu, select RS-232. In the Action drop down menu, select RS-232 string. Click on Submit Changes button. KGROUND R ALLOWS O INSTANT- ANGE THE LIGHTING RCENTAGE ED ON THE AL ILLUMI- 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Page 32
RS-232 channel 1. LB-KP16E-ICP Configuration Select the Keypad Type 16 Button Keypad on the System Configure page when configuring the LB-KP16E-ICP. Refer to the example above for button configuration. 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Both ends of the link are connected to the corresponding equipment and to the same corresponding channel port. c. Cable connections at both channels are securely fastened to each connector. Turn the power off, then back on to reset the link. 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)
Service at 800-214-0222 for information. 5.2 Return/Repair Service The LB-KP8E-ICP / LB-KP16E-ICP Button Keypad contains no user serviceable components. If you have a problem with your unit, please contact the Customer Service Department. To facilitate our return/ repair processing please contact Broadata Communications, Inc.
LIMITED WARRANTY 6.0 LIMITED WARRANTY Broadata Communications, Inc. (BCI) warrants, for a period of one year from date of ship- ment, each product sold shall be free from defects in material and workmanship. BCI will correct, either by repair, or at BCI’s election, by replacement, any said products that in our sole discretion prove to be defective and are returned to the manufacturing location within 30 days after such defect is ascertained.
Page 37
2545 West 237th Street, Suite K Torrance, CA 90505 1-800-214-0222 (310) 530-1416 (310) 530-5958 (Facsimile) e-mail: Sales@Broadatacom.com 2545 West 237th Street Website: www.broadatacom.com Torrance, CA 90505 800•214•0222 310•530•1416 e-mail: Sales@broadatacom.com www.broadatacom.com 8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)- 60000LNKP8_16EICP...