Related Manuals for Quattro QUATTRO500
Summary of Contents for Quattro QUATTRO500
- Page 1 Model No. QUATTRO500 (MANUAL) Model No. QUATTRO600 (AUTO) REMOTE CARAVAN MOVER Electronics installation guide, user information and troubleshooting REF: SW v1.0 QUATTRO500_ELECTRONICS_UM.indd 1 15/08/2019 16:47:53...
- Page 2 1. Press handset button Fig.1.C twice quickly 2. Turn caravan isolation key to the off position. Engage Mover (Quattro 600 Auto Only) 1. Press and hold handset button Fig.1.C for three seconds to begin engaging, once completed the handset will return to the home screen automatically.
- Page 3 Fig.A Fig.1 Fig.2 Fig.3 QUATTRO500_ELECTRONICS_UM.indd 3 15/08/2019 16:47:53...
- Page 4 Before First Use - Single Axle and Twin Axle Modes Page 5 Before First Use - Pairing the Handset and Control Unit(s) Page 5 Using Your Caravan Mover with Quattro Technology Page 5 Operation - Getting Started Page 6 Troubleshooting Page 6/7 Package Contents (Fig.A)
- Page 5 ‘A’ frame. Please refer to Table.B (below) for fitment of the motor units to the REAR of the axle. Note: If you are fitting two sets of motors onto a twin-axle caravan to form a AWD Quattro system refer to the wiring diagrams on pages 9 & 10 of this manual to ensure rear axle is correctly wired.
- Page 6 The mover has two Motor Units (Installation Manual 1 & 2). In general they are mounted in front of the axle of the caravan/trailer. Both units are identical, so either can fitted to nearside or offside framework. Please refer to appropriate Quattro500 or Quattro600 installation manual that is packaged in with your mover framework.
- Page 7 Engage both rollers as described in ‘Operation-Mover engagement’. For the Quattro500 (Manual) this only needs to be done on one side of your caravan since the other side will automatically follow via the cross actuation bar.
- Page 8 10cm of control box. Once succesfully paired the handset will return to the home Axle Mode Selection - By default Quattro systems are set to work in single axle mode, if installed as a twin axle or AWD system this setting should be changed to suit.
- Page 9 To use this remove the small rubber plug on the rear of the engagement motor and turn the engagement worm manually. Quattro500 (Manual Mover) - In order to engage the rollers, fit the end socket of the Engagement Tool (6) on the spindle (Fig.2G &...
- Page 10 Diagnostic settings menu icon. On the top face of the Quattro control box, under the Quattro logo are two small LED light indicators. If you are having an issue with your mover system, refer to the below to help identify the possible fault.
- Page 11 - Faulty control box. If correcting the above does not fix the issue it is likely that the control unit has a fault and will need repair or replacement. In case of any doubt, please call your Quattro Caravan Mover supplier. AWD - Front axle wiring Fig.4...
- Page 12 AWD - Rear axle wiring Fig.5 Positive Wire Negative Wire AUTO MODEL ONLY AUTO MODEL ONLY ISOLATION KEY FUSE Caravan Rear The upper connection on every motor should be wired with the black negative wire, while the lower should be wired with the red positive wire. This ensures all motors operate in the correct directions. Page 10 QUATTRO500_ELECTRONICS_UM.indd 12 15/08/2019 16:47:54...
- Page 13 AWD - Setup Refer to the table below and Fig.4 and Fig.5 to wire the AWD system correctly. Note that if any part of the system is wired incorrectly it could cause damage to the movers or caravan tyres if all rollers do not move in the correct directions. AWD - REAR AXLE FITTING AWD - FRONT AXLE FITTING Table .
- Page 14 Product Registration & Guarantee Please register your Quattro caravan mover online within 14 days of purchase to benefit from our 7 year ® warranty. Registration is quick and simple, go to www.purpleline.co.uk/product-registration. Please retain your original purchase receipt. Please fill-in the Serial Numbers + additional information and retain this manual for future reference.