1. Manuals
  2. Brands
  3. ZIV Manuals
  4. Switch
  5. SW3
  6. User manual

ZIV SW3 User Manual

Gigabit/fast ethernet switch
Hide thumbs
Table of Contents

Advertisement

Quick Links

GIGABIT/FAST ETHERNET SWITCH TYPE
Making the Smart Grid Real
SW3 (DIN)
USER GUIDE
V04 - May 2019
M0SW3D1905Iv04
ZIV
Carrer de les Ciències,149-151
08908 L'Hospitalet de Llobregat,
Barcelona-Spain
Tel.: +34 933 490 700
Fax: +34 933 492 258
Mail to: ziv@zivautomation.com
www.zivautomation.com
1/122

Advertisement

Table of Contents
loading

Related Manuals for ZIV SW3

Summary of Contents for ZIV SW3

  • Page 1 GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) USER GUIDE V04 - May 2019 M0SW3D1905Iv04 Carrer de les Ciències,149-151 08908 L’Hospitalet de Llobregat, Barcelona-Spain Tel.: +34 933 490 700 Fax: +34 933 492 258 Mail to: ziv@zivautomation.com www.zivautomation.com Making the Smart Grid Real...
  • Page 2  equipment or even injury to the personnel handling it. NOTE: Information or important aspects to take into account in a procedure, operation or alike. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 2/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 3: Table Of Contents

    MECHANICAL AND ELECTRICAL CHARACTERISTICS 10/100BASE-TX (RJ-45) PORTS 100BASE-FX (MULTIMODE, MT-RJ) PORTS 100BASE-FX (MULTIMODE, ST) PORTS 100BASE-FX (MULTIMODE, LC) PORTS SFP PORTS SRV PORT LED SIGNALLING GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 3/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 4 PORTS MONITORING CONFIGURATION LLDP CONFIGURATION 5.10 SNMP CONFIGURATION 5.11 STP PROTOCOL CONFIGURATION 5.12 NTP/SNTP CONFIGURATION 5.13 MULTICAST CONFIGURATION 5.13.1 Static 5.13.2 GMRP 5.13.3 IGMP 5.14 ACCESS CONFIGURATION GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 4/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 5 ABBREVIATIONS APPENDIX B DATA STRUCTURE IN CLI ACCESS METHODS USER CONSOLE COMMANDS OBTAINING INFORMATION ABOUT THE STATUS AND EQUIPMENT CONFIGURATION CERTIFICATE INSTALLATION FOR HTTPS MANAGEMENT GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 5/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 6: Introduction

    SW3 devices bring the necessary capabilities to implement the automation of electrical substations according to the IEC 61850 standard. The SW3 can be managed locally and remotely, through a local console, Telnet server and SSH server, or through a built-in web server, HTTP or HTTPS.
  • Page 7 FIGURE 1 Traffic separation FIGURE 2 Star topology GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 7/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 8 (access and core). Once the LAG is selected, the set of parameters of the interface selected as Leader determines the behaviour of the group. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 8/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 9 Q-in-Q operation ❖ Advanced RSTP implementation. The SW3 not only complies with the STP and RSTP protocols for resolving loops in the network and operation in rings, but it also exceeds the recovery times obtained through said protocols. Thus, the SW3 guarantees recovery times lower than 4 ms per link via the RSTP standard in case of failure.

  • Page 10: Equipment Composition

    The SW3 also selects the multicast flows in an explicit and manual way. ❖ Port mirroring. The SW3 resends traffic copies of one or more ports to another one, the monitoring port, being able to select incoming or outgoing traffic copies in each monitored port in an independent manner.

  • Page 11: Technical Specifications

    ➢ Multiple VLANs management (250 simultaneously). ➢ QoS: • the SW3 can use the priority fields included in the IEEE 802.1p tag, • as well as the DSCP identifier included in the IP header. ➢ Broadcast and Multicast (Broadcast Storm Control) traffic limitation.
  • Page 12 Multimode fiber MTRJ-ST, 2m length (4CZ05000012). • Multimode fiber MTRJ-LC, 2m length (4CZ05000013). • Multimode fiber LC-LC, 2m length (4CZ05000014). • Singlemode fiber LC-LC, 2m length (4CZ05000015). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 12/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 13: Equipment Management

    Multirange model is also protected against polarity inversion. ➢ Consumption: Maximum consumption at 48 V : 12 W. Maximum consumption at 230 V : 22 W. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 13/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 14 EN 61000-4-11 standard. • Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests: in accordance with EN 61000-4-29 standard. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 14/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 15: Warnings

    - Only qualified personnel appointed by the electricity company that owns the installation should carry out the installation and handling of the SW3. - The environment in which it is to operate should be suitable for the SW3, fulfilling all the conditions indicated in section 1.4.8.

  • Page 16: Equipment Safety Considerations

    SW3 must be free of static electricity. An anti-static wristband and/or heel connected to earth should be worn. - The room housing the SW3 must be free of elements that can generate static electricity. If the floor of the room is covered with a carpet, make sure that it is anti-static.

  • Page 17: Mechanical And Electrical Characteristics

    MECHANICAL AND ELECTRICAL CHARACTERISTICS The diverse elements comprising the SW3 are supplied in a box suitable for DIN-rail mounting, see FIGURE 5 and FIGURE 6. FIGURE 5 General dimensions in mm of the SW3 GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)
  • Page 18 FIGURE 6 Detail of the DIN rail fastening element Inserting Removing GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 18/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 19 The SW3 is powered with a nominal voltage of 48 V isolated (10.5-72 V ) or allows DC and AC supply-voltage operation (36-360 V , 80-265 V ), through the connector shown in FIGURE 7. The female connector supplied with the equipment is suitable for rigid or flexible conductors of up to 2.5 mm...
  • Page 20 The SW3 may have 8 RJ-45 connectors or 4 RJ-45 connectors and 4 MT-RJ or, upon request, LC or ST connectors. It also has two Gigabit Ethernet SFP bays. FIGURE 8 Front view of the SW3 a) 8 RJ-45 connectors...

  • Page 21: 10/100Base-Tx (Rj-45) Ports

    FIGURE 11 shows the use of each one of the pins of the RJ-45 connector, as well as the pair it belongs to according to ANSI/TIA/EIA-568-A standard, in the 10/100Base-Tx LAN interface. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 21/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 22 Unshielded twisted pair category five cable (UTP-5) with RJ-45 connector according to ANSI/TIA/EIA-568-A standard FIGURE 11 Signals of the RJ-45 connector in the 10/100Base-Tx LAN interface GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 22/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 23: 100Base-Fx (Multimode, Mt-Rj) Ports

    FIGURE 13 shows the most important input and output optical power characteristics according to the type of multimode fiber used. All the MT-RJ type connectors have a protective cap. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 23/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 24: 100Base-Fx (Multimode, St) Ports

    FIGURE 13 shows the most important input and output optical power characteristics according to the type of multimode fiber used. All the ST type connectors have a protective cap. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 24/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 25: 100Base-Fx (Multimode, Lc) Ports

    5. Remove the protective caps from the optical ends of the module. 6. Insert the fibers, in the optical ends of the module, keeping in mind the TX and RX data transmission directions (see FIGURE 14). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 25/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 26 SFP outward). FIGURE 15 Removing an SFP transceiver GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 26/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 27: Srv Port

    RD (Out) TD (In) SRV CONNECTOR (DCE mode) Interface type ITU-T V.24/V.28 (EIA RS-232) Connector DB9 female Data Asynchronous Speed 115200 bit/s Protocol CLI (system console) GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 27/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 28: Led Signalling

    The SW3 has two basic LEDs (SRV and ON) and several specific LEDs associated with the Fast Ethernet ports and SFP modules. FIGURE 17 shows a front view of the SW3, showing the detail of the different LEDs. They are described below.

  • Page 29: User Guide - M0Sw3D1905Iv04 - V04 May

    Amber. There is one LED per SFP interface. It stays on when the transmission is Full-duplex and goes off when the transmission is Half-duplex. It flashes in the case of collision. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 29/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 30: Access To The Equipment

    ACCESS TO THE EQUIPMENT The SW3 can be managed locally and remotely, through a console or through a built-in web server. The server operates with the HTTP and/or HTTPS protocol. CONSOLE The equipment provides a user console application called CLI (see APPENDIX B accessible through the SRV connector, a standard DB9 female connector in DCE mode that operates at 115200 bit/s, with 8-bit characters, without parity and with a stop bit.

  • Page 31: Http Server

    5.17, 5.18, 5.19 and 5.20 respectively. The Apply, Save and Reboot commands request confirmation of the operation from the user before it is actually executed. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 31/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 32 It should be borne in mind that if the IP address is changed, the IP address of the client equipment must also be changed accordingly. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 32/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 33: Configuration And Management

    CONFIGURATION AND MANAGEMENT Configuration and management of the SW3 is performed through the console and through Access to the equipment HTML pages. All the parameters controlling the equipment operation are described below in detail, using the real HTML pages as an auxiliary graphic sample.

  • Page 34: General Parameters

    GENERAL PARAMETERS The general parameters are grouped on the first page, see FIGURE 19, which is shown when the SW3 validates the user identity. In addition to the configuration parameters, which will be described in the following sections, as shown in the figure, the system provides information about the equipment software, that is to say, version being executed, and equipment hardware, that is to say, serial and tracking number.

  • Page 35: Equipment Identification

    It is advisable to store the new password in some type of register as, should the new password be forgotten, it is not possible to access the web server. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 35/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 36: Others

    Remote Syslog server. Valid values are 1 to 8. The default value is 4. See information about the levels in the previous parameter. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 36/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 37: Administration

    • Messages.1 • Messages.2 • Messages.3 • Security • Security.0 The credentials for accessing the FTP folder are the same as for accessing the equipment. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 37/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 38: Lan Configuration

    Static IP. When this control is selected, the equipment uses the data provided by the user in relation to the IP address and its mask. The main IP address and its mask are obtained automatically through the DHCP server. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 38/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 39: Ethernet Ports Configuration

    Ports 9 and 10 are always associated with the SFP ports. • Enable. This permits a port to be enabled or disabled, by ticking or not ticking the respective Enable box. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 39/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 40 This mode of operation is equivalent to Native VLAN of Cisco, with the consideration that the native VLAN is port-to-port defined by means of the VID parameter. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 40/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 41 For the interfaces operating in QinQ Access mode, the value of this parameter determines the VLAN identifier to be included in the most outer tag on the interfaces with double tag, the so-called S-Tag. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 41/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 42 If interfaces are configured as members of a group but none of the interfaces is selected as Leader of it, the group will not be effective. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 42/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 43: Vlan Configuration

    IEEE 802.1q. The tag allows several VLANs to share resources, including switching devices such as the SW3, or links between switching units, with the guarantee that the traffic from each VLAN will reach the correct destination.
  • Page 44 (see the VID ACL parameter in section 5.4). FIGURE 24 shows an example for using the Overlapping Enable parameter. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 44/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 45 PRI. If the PRI Override option is enabled, the original priority of the frames received with a tag will be modified with the selected value. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 45/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 46 VLAN is a priority and would not be considered for the operation of Q-in-Q. FIGURE 25 Example for using the VLAN for Q-in-Q parameter GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 46/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 47 Traffic received from a Trunk will be denied if it belongs to an Isolated Community VLAN. It will only be permitted if it belongs to the primary VLAN. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 47/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 48: Bandwidth Limit Configuration

    The data volume limit may be selected in general for all types of traffic, as well as for certain combinations that take into account the type of messages. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 48/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 49 Rate (bps). It sets the maximum outgoing bandwidth from the port: 64000 bps (64 kbps) to 250000000 bps (250 Mbps). The maximum data rate only affects the Gigabit Ethernet ports. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 49/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 50: Qos Configuration

    IEEE 802.1p, with four internal priority levels. This priority is taken into account for selecting the processing and transmission order in each switch output interface. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 50/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 51 Although it is available, it is recommended to reserve the Mgmt priority for exclusive use as priority 7, avoiding the use of such priority for user traffic. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 51/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 52 - The priority present in the frame will be maintained in a tagged frame, provided the DSCP field is not present (traffic or IP) or does not coincide with any of the specified values. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 52/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 53: Ports Monitoring Configuration

    The menu parameters are divided into two quite different blocks, which are: Incoming traffic monitoring (Ingress Monitoring). Outgoing traffic monitoring (Egress Monitoring). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 53/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 54 • Target port. It sets the port where the replicated packets will be sent to be monitored. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 54/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 55: Lldp Configuration

    Both the information transmitted and the information received is accessible through the SNMP protocol, through the MIBs defined in the LLDP standard itself, and is usually used to determine the topology of the networks. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 55/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 56 In order for SNMP notifications to be effectively sent, they must be explicitly allowed to be sent in the SNMP menu. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 56/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 57 The protocol has its own statistics that show the data specific to the execution of the protocol in each interface as part of the information received. FIGURE 31 Example of configuration of LLDP menu GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 57/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 58: Snmp Configuration

    (Auth Alg.) and authentication password (Auth Password), it is necessary to select the cipher algorithm (Priv Alg.), DES o AES, and select the cipher password (Priv Password). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 58/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 59 (trap) or confirmed (inform) way. • Enable LLDP Trap. Indicates the SNMP agent whether the notifications created by the LLDP agent are allowed or not. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 59/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 60: Stp Protocol Configuration

    Version. This sets which of the possible protocol versions will be executed. STP or RSTP (Rapid STP). • Bridge Priority. This sets the priority of the device communicating with the root device. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 60/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 61 Tx Hold Count. This sets the maximum number of BPDU packets that can be transmitted in one second. The default value is 6 and valid values are 1 to 10. FIGURE 33 STP menu configuration page GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 61/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 62 PtP, this allows greater speed in protocol convergence, and the agreement process on changing the state of a link from designated to non-discarding (operative for user traffic) is speeded up. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 62/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 63 Edge_Tx_filter active lead to switches being unable to detect the connection as part of a loop. FIGURE 34 Example of the redundant mode of the interface with respect to the STP GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 63/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 64: Ntp/Sntp Configuration

    IP. IP address of the NTP server. • Type. This sets the type of messages to be sent to the NTP server. The messages can be individual (unicast) or collective (manycast). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 64/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 65: Multicast Configuration

    Under normal conditions, multicast traffic propagates automatically on all interfaces belonging to each VLAN, with client devices that selectively enable the reception of specific multicast addresses in which they are interested. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 65/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 66 Any other multicast traffic will be discarded. As an example, FIGURE 37 shows the advantages of using GARP/GMRP or IGMP Snooping. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 66/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 67 Example of using the GARP/GMRP or IGMP Snooping a) Network that does NOT use Multicast configuration protocols b) Network that uses GARP/GMRP or IGMP Snooping in its level-2 devices GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 67/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 68: Static

    The value all means the vlan is not relevant. Example: in equipment with the vlan1, vlan3 and vlan4 defined, the group of numerical identifiers will be 1,3,4. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 68/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 69: Gmrp

    Forward All Groups: The equipment allows manual configuration of this special address individually for each interface. • #. It sets the equipment physical port number. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 69/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 70: Igmp

    5.13.3 IGMP The IGMP Snooping is an optimization to be used in level 2 devices, such as the SW3. The IGMP protocol is level 3; therefore, the IGMP Snooping operation performed by the switch is conditioned by the presence of a Multicast router in the network.
  • Page 71 Configured in auto, the port will selectively transmit the multicast messages if there are client devices registered in the corresponding group. FIGURE 40 IGMP configuration page of Multicast menu GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 71/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 72: Access Configuration

    For this purpose, the equipment has a TACACS+ client and a RADIUS client. FIGURE 41 Access menu configuration page GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 72/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 73: User Guide - M0Sw3D1905Iv04 - V04 May

    RADIUS server is equal to or more than this parameter, and at the same time lower than the Admin level, the user will get guest access (read only). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 73/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 74: Security Configuration

    (none option). • Max. Addresses. This sets the maximum number of MAC addresses permitted at one time in the indicated port. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 74/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 75 The parameter is expressed in seconds, and the accepted value range is between 1 and 86400 (1 day), where the default value is 3600 (1 hour). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 75/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 76: Mac List

    This submenu permits the authorized client MAC address list to be specified. The list may or may not be activated in each port through the Security type parameter. FIGURE 44 MAC list submenu configuration page GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 76/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 77: Others Configuration

    Bridge Age Time. It sets the maximum time a learned MAC address of inactivity will remain in the switch MAC address table. Valid values, in seconds, are 15 to 3600. The default value is 300. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 77/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 78: Reboot

    The Only verify option allows users to check that the code saved is coincident with the binary image selected without affecting the installed image. FIGURE 46 Reflash configuration page GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 78/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 79: Configuration File

    If the Only verify option has been selected, and verification has been successful, it is indicated by the system to the user. If desired, the configuration can be applied by means of the Apply and Save commands or both. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 79/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 80: Download (From The Equipment To The Pc)

    HTTP browser used by the user, as well as the actions that must be performed with the received file (for example, where to store it, etc). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 80/122...

  • Page 81: Statistics

    The statistics can be REBOOTED by the user at will, from the console by running the clear command in the prompt, or using the menu option Clear Statistics. FIGURE 49 Example of statistics with general data GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 81/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 82 FIGURE 50 Example of basic statistics of Ethernet ports FIGURE 51 Example of statistics detail of a specific port (selection of # parameter) GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 82/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 83 FIGURE 52 Example of statistics of the MAC addresses identified by the switch FIGURE 53 Example of statistics of the STP protocol GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 83/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 84 FIGURE 54 Example of statistics of the LLDP protocol FIGURE 55 Example of statistics of NTP client GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 84/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 85: Appendix A Bibliography And Abbreviations

    APPENDIX A BIBLIOGRAPHY AND ABBREVIATIONS GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 85/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 86: Bibliography

    GPRS General Packet Radio Service Generic Routing Encapsulation HTTP HyperText Transfer Protocol ICMP Internet Control Message Protocol IGMP Internet Group Management Protocol Internet Key Exchange GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 86/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 87 Subscriber Identity Module SMTP Simple Mail Transfer Protocol Spanning Tree Protocol Transmission Control Protocol User Datagram Protocol UMTS Universal Mobile Telecommunications System Uniform Resource Locator GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 87/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 88 VRID Virtual Router Identifier VRRP Virtual Router Redundancy Protocol Wide Area Network Wired Equivalent Privacy WINS Windows Internet Naming Service Wi-Fi Protected Access Client Support GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 88/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 89: Appendix B Data Structure In Cli

    APPENDIX B DATA STRUCTURE IN CLI GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 89/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 90: Access Methods

    Stop bits: 1 • Flow control: No → → → © In Windows XP execute HyperTerminal from Start All Programmes Accessories → Communications HyperTerminal (see FIGURE 56). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 90/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 91 On opening HyperTerminal a text box appears, requesting the necessary information to establish the connection (see FIGURE 57). FIGURE 57 Connection configuration through the serial port with HyperTerminal GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 91/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 92 In the Serial menu (last of all) the serial port is configured. If an USB converter is used, first, consult the COM number in the Device administrator (Control panel). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 92/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 93 FIGURE 59 Device administrator window FIGURE 60 Connection configuration through the serial port with Putty GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 93/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 94 Execute.. Telnet text window to establish connection with the equipment On pressing the Accept button a System symbol window will appear with the Telnet programme connected to the equipment (see FIGURE 62). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 94/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 95 Then, in the window of Characteristics of Windows, select Telnet client, see FIGURE 63. By pressing Accept, the Telnet client of Windows may be used. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 95/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 96: User Console Commands

    The following table shows a full list of available commands with a brief description of each one and their availability depending on the type of user starting the session, highlighting the most useful ones. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 96/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 97 It closes with Ctrl+C. telnet Open a telnet session without interrupting the connection with ✓ ✓ the equipment. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 97/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 98 In the information block, the values are notice, info and debug, without having any connotation whatsoever for impact. For more information, see section 5.1.4, Syslog. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 98/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 99 For this reason, this command is useful for configuring equipment with the same parameters as the current one. Syntax: swt /> download Arguments: GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 99/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 100 Examples: swt /> get swt /> get main swt /main> get hostname swt /> get main/hostname swt /admin> get ../main/hostname GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 100/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 101 However, these changes will not take effect until the equipment is rebooted. Syntax: swt /> save Arguments: Observations: This command can be used irrespective of the directory where the user is. Example: swt /> save GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 101/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 102 Examples: swt /main> set hostname swt /> set main/hostname swt /admin> set ../main/hostname swt /> set nat[2]/origin GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 102/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 103 This closes the connection between the computer and the equipment, and therefore the CLI program session. Syntax: swt /> quit Arguments: Observations: Example: swt /> quit GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 103/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 104 The 3 letters identifying the equipment can be used as the host name. Example: swt /> telnet drn swt /> telnet 172.16.50.38 23 GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 104/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 105 The higher the suffix oldest is the file contents. Use the show command to display the oldest files. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 105/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 106 When this command is executed the equipment starts to send pings to the indicated host until the user presses the Ctrl.+C keys. Example: swt /> ping 172.16.50.38 swt /> ping emr GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 106/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 107 To show a parameter for a specific status or those of a specific directory, the names of each one must be known. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 107/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 108 When this command is executed, the equipment remains to show all the events taking place in the equipment until the user presses the Ctrl.+C keys. Example: swt /> tail GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 108/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 109: Obtaining Information About The Status And Equipment Configuration

    “telnet 111.222.0.123” (without inverted commas) and then press Accept. If everything is functioning normally, a window will pop up with a system symbol, which is the interface for the connection. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 109/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 110 If the login and password entered are correct, the prompt swt /> will appear, indicating that the equipment is waiting for a command to be entered. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 110/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 111 To copy the text from the Windows XP © command window, right-click with the mouse and select Mark in the menu that appears. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 111/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 112 After releasing the left button, press the enter key. That way, you will have copied the selected text into the Windows clipboard. Now open Windows Notepad and paste the text (Ctrl. + V) in a .txt file and save it. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 112/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 113 Remember to save the information in a .txt file as indicated above. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 113/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 114 Once the command is activated, it will remain to show events as they occur until the user presses Ctrl.+C. Remember to save the information in a .txt file, as indicated above. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 114/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 115 [dscp] queue ------------- medium medium medium medium medium medium Press any key to continue or CTRL+C to stop. [A medium medium GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 115/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 116 ----------------------------------------------------------------------------------------------- -------------------------------------------------------------------------------------------------------- ------------------ Press any key to continue or CTRL+C to stop. [A TxRx 0.0.0.0 TxRx 0.0.0.0 TxRx 0.0.0.0 TxRx 0.0.0.0 TxRx 0.0.0.0 GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 116/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 117 Press any key to continue or CTRL+C to stop. [A server1_ip = 0.0.0.0 server2_ip = 0.0.0.0 encrypted = on shared_key = tH4sIADyDDlwCAzO0NDA0NTA30QYAxs/cjQkAAAA1Nzk0MzZkYzhjYzIwNmUzRMzJiZjMwMDdkMTI2NjJjYwo= GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 117/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 118 Press any key to continue or CTRL+C to stop. [A reauth_enable = on reauth_period = 3600 reauth_max quiet_period = 60 radius_server/ = 0.0.0.0 udp_port = 1812 secret tH4sIADyDDlwCAzO0NDA0NTA30QYAxs/cjQkAAAA1Nzk0MzZkYzhjYzIwNmUzRMzJiZjMwMDdkMTI2NjJjYwo= swt /> GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 118/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 119: Certificate Installation For Https Management

    5. In the equipment, activate the access by means of HTTPS (“set https on”). 6. Apply the changes (“apply”). 7. Save the new data (optional) (“save”). GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 119/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

  • Page 120: User Guide - M0Sw3D1905Iv04 - V04 May

    The operation is a success with Microsoft Internet Explorer and Mozilla Firefox. Google Chrome doesn’t accept the certificates authorized by you. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 120/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 121 An example of certificate, as well as private key, is shown in the following. Pay attention that both the header and bottom lines are part of the certificate. GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 121/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...
  • Page 122 Example of a valid private key: -----BEGIN RSA PRIVATE KEY----- MIICWwIBAAKBgQC3j0h918P/FU4ayovbXuzpq6Z0Vav01ignDrwtusdjRVn04bB6 f5qVcCMFyXaWotmN/WU6HbnRpYR5ksffWUPlvFL1z7DxivBehYSdg7FRCkrj1ga8 fsOeosDIjmm3JBt3IyhOQxzEE5mM2hOhWKgaJn0ZEGDqcoIMLj4/E3f/3QIDAQAB AoGAOvDzYhVKhjodHlUzm3lbsZzAklKAKNorgn8kxbpYE/RM8mkV9f/Lb3jWhiEu xyf7m7BmNMcex8bSRwduzrUnK66DW8jP3b2tsxJHLYU9UpN1XKDNBHGvgJ7Gis+S ApuoZFYmh34uBl6SJkUdihCs4jM1ocQBQMHQ7mXe7Sk1sgECQQDgpSDx45vm8Yk+ GoX4UzcRIDoU47P3uHnnPTYUQMMqDta3K4bzualwcNOpU8bFtQbWfxjkThHthQBN rUeEREj9AkEA0S4ernXQGVJGm7b6JhJXFKkILVYo5vP0C3jx7ByRIMt4lkll4l7Q tzNepKjlcmimzLWuHJAiyTBtvzfVcnU4YQJAaXOaX3HkwSgosIpq0QLfGp7yJNQu qt5h+vZ06FTuSFPm3t0D4G0K6MlN0nKNIEm2CAJpgOJU8BY66jupEqGrUQJAW7Wp s/lpJEDjPg/p+lkeHqvBLwdQZXldbM442rjnlAZBNzq01ZuWTEvUWcLG3fMt9iBN Vq6G4cg+xZA4H7du4QJALq/zgc4N+Ft50Hkj+ay1XSt5nxH8U2Zk1u7ZWZZhOTcw ezG/TDLBWkROF2n9VX6TYGesnZ2Ve/+DiMPhK7ZVQA== -----END RSA PRIVATE KEY----- GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN) 122/122 USER GUIDE - M0SW3D1905Iv04 - V04 May 2019...

Table of Contents