1. Manuals
  2. Brands
  3. TECWELD Manuals
  4. Welding System
  5. Sherman digitec DIGITIG 210P
  6. User manual

TECWELD Sherman digitec DIGITIG 210P User Manual

Welding rectifier inverter
Hide thumbs
Table of Contents

Advertisement

Quick Links

V1.2 19/01/23
USER MANUAL
WELDING RECTIFIER Inverter
DIGITIG 210P

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sherman digitec DIGITIG 210P and is the answer not in the manual?

Questions and answers

Related Manuals for TECWELD Sherman digitec DIGITIG 210P

Summary of Contents for TECWELD Sherman digitec DIGITIG 210P

  • Page 1 V1.2 19/01/23 USER MANUAL WELDING RECTIFIER Inverter DIGITIG 210P...
  • Page 2 WARNING! Before installing and commissioning, please read these instructions 1. GENERAL Commissioning and operation of the device can be made only after a careful reading of this handbook. Due to the continuous development of technical equipment, some of its functions can be modified and operation may differ in detail from the description in the manual.
  • Page 3 Poisoning prevention vapors and gases evolved at the time of welding of coatings for welding electrodes and evaporation of metals: • Use ventilation and exhaust installed in limited air exchange. • Blow fresh air when working in a confined space (tanks) •...

  • Page 4: Specifications

    3. GENERAL DESCRIPTION The device DIGITIG 210P is used for manual welding structural steel coated electrodes (MMA method) and quality steels, copper and its alloys tungsten inert gas (TIG). This is the inverter device, manufactured with the most technologically advanced components made in IGBT technology. Welding has an adjustable ARC FORCE and the ability to adjust the frequency of the pulse, fall time and current powypływu gas.

  • Page 5: Connection To The Mains

    5. CONSTRUCTION AND OPERATION The basis for the construction of the power conversion electronics welders are made in IGBT technology for working in the frequency range above 200 kHz. The principle consists of a single-phase rectified voltage to the power supply voltage, conversion of the resulting DC voltage to a square wave high frequency voltage transformation in the range required by the welding process and re-erection of the resulting voltage on the DC voltage.
  • Page 6 7.2 TIG Current terminal holder should be connected to the negative pole (9), plug control handle carefully screwed into the socket (11) and a gas connection to the socket (10). Gas conduit from the regulator, lead and attach to the gas nozzle (17) arranged on the rear wall of the housing. The positive pole of the source (8) connected to the work piece by means of a wire with a clamp.
  • Page 7 8. FUNCTIONAL DESCRIPTION switches and DIAL 1. Display 10. The seat of protective gas 2. The LED power 11. Socket control TIG 3. indication of improper operation Button 12. pulsator 13. Key control the source (two-stroke engine / 4. Welding current regulator czterotakt) 5.
  • Page 8 ARC FORCE ARC FORCE allows the arc. Shortening the length of the arc is accompanied by an increase in the welding current, which results in stabilizing the arc. Decreasing the value will give a soft arc and a smaller depth of penetration, while increasing the value results in deeper penetration and the possibility of short-arc welding.
  • Page 9 To ignite the arc mode dwutaktu must approach the electrode to the workpiece at a distance of a few millimeters, and press the button on the handle of the torch. After the correct initiation of arc welding lead the button pressed. Releasing the handle causes us to start phase downslope and end of the welding process.

  • Page 10: Maintenance Instructions

    4 Gas nozzle T-26 4 Gas nozzle T-26 For a full list of consumables and spare parts is available on the website and in the company www.tecweld.pl TECWELD. There is a possibility of direct purchase of these parts. 14. MAINTENANCE INSTRUCTIONS As part of the everyday operation of the welder must be kept clean, check the connection status and the status of external electrical wires and cables.
  • Page 11 15. INSTRUCTION STORAGE AND TRANSPORT The device should be stored at -10 ° C to + 40 ° C and relative humidity 80% free of corrosive fumes and dusts. Transportation of packaged devices should be covered means of transport. For transport the packaged unit must be secured against slipping and ensure the correct position. 16.
  • Page 12 In the case of warranty repair should contact TECWELD, which will arrange the reception device by courier. Consignments sent in a different way at the expense of the company TECWELD will not be accepted! Welder should be provided with the welding torch.

  • Page 13: Declaration Of Conformity

    DECLARATION OF CONFORMITY 01 / DIGITIG210P / 2018 Manufacturer's authorized representative: TECWELD Peter Polak 41-943 Piekary Slaskie Street. Emerald 21/3/6 branch: 41-909 Bytom ul. 3 Cross POLAND Declare that the said product: inverter welder Trade name: DIGITIG 210P Type: TIG 200P...

Table of Contents