Table of Contents
Advertisement
Quick Links
Adaptable Heat Drying System
INSTRUCTION MANUAL
Models: FGPH102; FGPH103; FGPH104; FGPH105;
FGPH106; FGPH107; FGPH108; FGPH109; FGPH110
Ensure that you have read and understand this manual before operating the machine.
Do not overload sockets or extension cords. Check power ratings before use.
Risk of electric shock. Do not open the unit or try to reach through the grills.
Ensure a suitably sized air mover is used that matches the size of the Drymatic Boost grill.
Minimum recommended airflow required: 1100m³/Hr (650 cfm). Do not position air mover
more than 50cm (19") away from the Drymatic Boost Bar inlet.
Manufactured in the UK by DBK Technitherm LTD
All worldwide design rights and copyright reserved
WARNING!
Advertisement
Table of Contents
Related Manuals for DBK Drymatic Boost Bar FGPH102
Summary of Contents for DBK Drymatic Boost Bar FGPH102
- Page 1 Adaptable Heat Drying System INSTRUCTION MANUAL Models: FGPH102; FGPH103; FGPH104; FGPH105; FGPH106; FGPH107; FGPH108; FGPH109; FGPH110 Manufactured in the UK by DBK Technitherm LTD All worldwide design rights and copyright reserved WARNING! Ensure that you have read and understand this manual before operating the machine.
-
Page 2: Congratulations On Your Purchase
Please complete and mail, fax or email your warranty registration card complete with bill of sale/receipt to activate your warranty. DBK Technitherm offers a standard two year comprehensive warranty from the date of purchase on Drymatic Boost Bar. Contact details can be found on the reverse of this instruction manual. - Page 3 Do not remove adhesive labels. Only use Drying Mats/accessories branded by Drymatic or DBK. Ensure air movers match the Boost Bar inlet size- recommend airflow is 1100m³/Hr (650 cfm) (Manufacturers recommended airflow) Handle the unit carefully.
- Page 4 IMPORTANT SAFETY INFORMATION: HANDLE WITH CARE! KEEP AWAY FROM CHILDREN! RISK OF ELECTRIC SHOCK! RISK OF BURNS! It is recommended to run the unit on a 230V or 120V supply circuit protected by a Ground Fault Circuit Interrupter (GFCI) or a RCD. It is also recommended to regularly PAT (Portable Appliance Test) the machine.
- Page 5 Raising the temperature of the water damaged materials increases their vapour pressure and subsequently gives the material more potential for evaporation, resulting in more efficient drying. The DBK Drymatic Boost Bar has an intelligent control system that regulates its output to ensure that the temperature stays within the dialled-in range by varying the power of the heating device.
-
Page 6: Product Outline
Air Guides Switch Plate with Fuse and Power Switch *Only replace fuse with a 15A, 250/500V ceramic type fuse as marked on the unit. (DBK part number: EC308) Storage and Transport When finished with the machine the fixed mains cord can be wrapped around one of the inlets/ outlets and the plug can be clipped into cord retainer as shown. - Page 7 Set up Guide The Drymatic Boost should be set up using the following procedure: Place Drymatic Boost Bar either flat or vertical on the floor with an air mover directed at one of the grills. A Fan to Boost connector can be used to maximise airflow through the unit. Optional - Connect any Drymatic Wall and Floor Systems or any accessories you may wish to use.
- Page 8 2.2 Optional - Connect Drymatic Boost Bar Adaptors Drymatic Boost Bar has been designed to work with a series of adaptors that allow you to target the heated airflow in to areas that may otherwise be difficult to access such as Crawlspaces, Ceiling Voids, Cavity Walls and Tented Areas. The Boost Bar is supported by the following adaptors: ...
- Page 9 Set up Guide— 4-Port Adaptor (100mm) The Drymatic Boost 4-Port Adaptor is designed to split the heated airflow in to 4 separate channels; these can then be di- verted in to other rooms within a property or in to separate drying chambers, voids or cavities. Step 1—...
- Page 10 38mm Pipes and Plastic Cuffs Each port is 38mm and we recommend that users only fit the attachments supplied by DBK for the device. The adaptor is supplied with a kit containing black plastic cuffs, 38mm plastic hose and rubber bungs to seal off the end of each pipe if required.
- Page 11 Set up Guide— 90Deg Adaptor The Drymatic Boost 90Deg Adaptor is designed to divert the heated airflow in one of two different ways: Upwards—This could be used to simply heat the ambient air in a room or a ceiling void in combination with Lay Flat Ducting.
- Page 12 3. Power up the machines Plug the air mover and the Drymatic Boost into an appropriately rated power outlet. Switch the air mover on first then use the red power switch next to the cord to power up the Drymatic Boost Bar. It is good practice to switch on the air mover first but not essential.
-
Page 13: Current Limiter
5. Current Limiter The Boost Bar has an optional Current Limiting feature that allows the technician to de-rate the heater in the event of limited power availability on site. The user can select the maximum current available on the circuit and the on-board electronics will then monitor power usage and regulate the heater power based on current draw. -
Page 14: User Maintenance
3) Remove the old fuse and replace with new one. 4) Close the fuse holder with screwdriver. Replacement fuses must be 15A, 250V or 500V fast blow ceramic types (DBK part number: EC308). In the event of damage, repairs or any other maintenance requirements please contact your local Drymatic representative. -
Page 15: Troubleshooting
Trouble Shooting: In the event of a fault the first thing to try is powering down the machine, turning off the power at the mains and then waiting ten seconds. You can then power it up again and see if there are any improvements. If not please refer to this troubleshooting table for causes and solutions. -
Page 16: Model Identification
Model Identification: The model number and serial number on your machine can be used to identify your products type and more detailed power ratings from the specification table. This serial number can be found on the sticker above the handle on your machine. Model Number Serial Number: Unique 4 digit... - Page 17 Models: FGPH102; FGPH103; FGPH104; FGPH105; FGPH106; FGPH107; FGPH108; FGPH109; FGPH110 DBK Technitherm Limited Unit 11, Llantrisant Business Park, Llantrisant, CF72 8LF, Wales, United Kingdom Tel: +44 (0) 1443-23-79-27 Fax: +44 (0) 1443-23-78-67 Email: info-uk@dbk-group.com Web: http://drymatic.com All worldwide design rights and copyright reserved. Housing Only cULus/FCC only applies to models: FGPH104, FGPH107, FGPH109 &...