Advertisement
Professional model of air riveter to install blind rivets.
¡ Thank you very much for purchasing "LOBSTER" air riveter. To ensure correct operation, please
read this instruction manual carefully, and keep it in a safe place for later reference.
¡ This instruction manual contains information for models AR-011S, AR-011M and AR-011H.
Be sure to refer to information that is applicable to the model you are using.
¡ This is Original instructions. (Original Instruction Manual is written in English language.)
MANUFACTURER
International Marketing Department
12-8 Shijo-cho, Higashi-Osaka City
Osaka 579-8053, Japan
Telephone: +81(729)81-7466
e-mail: lobtex@riveter.com
URL http://www.riveter.com
AIR RIVETER
INSTRUCTION MANUAL
Telefacs: +81(729)81-9420
AR-011S
AR-011M
AR-011H
CONTENTS
INSTRUCTIONS ...........................1〜2
NOMENCLATURE .............................3
TECHNICAL DATA.............................3
PREPARATION BEFORE USE..........4
OPERATING THE AIR RIVETER ......5
MAINTENANCE ...........................6〜7
STORAGE ..........................................7
TROUBLESHOOTING .......................8
9〜10
11〜12
13〜14
PRINTED IN JAPAN
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for LOBSTER AR-011S
Summary of Contents for LOBSTER AR-011S
-
Page 1: Table Of Contents
13〜14 Professional model of air riveter to install blind rivets. ¡ Thank you very much for purchasing “LOBSTER” air riveter. To ensure correct operation, please read this instruction manual carefully, and keep it in a safe place for later reference. -
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS ◆ Be sure to read the following Important Safety Instructions carefully and make sure that you understand them thoroughly before using this tool. ◆ Always wear eye-protection at all times during use. If this is not observed, the rivet shaft (cut-mandrel) may eject out when the rivets are cut and cause serious injury. - Page 3 ¡ Repair work should only be carried out by a qualified technician. Please contact your nearest “LOBSTER” distributor, representative, or direct to Lobtex Co., Ltd., Osaka. If the tool is repaired by someone without the necessary qualifications and experience, the tool may not perform to optimum standards, and accidents or injury may result.
-
Page 4: Nomenclature
NOMENCLATURE FRAME HEAD NOSE PIECE FRAME HEAD INTERNAL PARTS FRAME CAP LOCK WASHER JAW CASE AR-011S SAFTY CAP NUT LOCK NUT JAW CASE PUSHER TRIGGER SAFTY CAP JAWS ‘S’ JAW PUSHER SPRING AR-011M・AR-011H LOCK JAW PUSHER WASHER CYLINDER SPRING JAW CASE... -
Page 5: Preparation Before Use
¡ The tool is available to install 6.4 mm (1/4”) rivets subject to conversion of jaws, jaw case head, jaw pusher and nosepiece. (Refer to page 6) AR-011H AR-011S AR-011M Rivet Dia. Nose piece Jaw case Nose piece Nose piece... -
Page 6: Operating The Air Riveter
OPERATING THE AIR RIVETER Select a rivet of a size which is suitable for the workpiece to be riveted. Replace the nosepiece with one which matches the size of the rivet to be used. (Refer to item in “Preparation Before Use” on page 5.) Drill a hole of appropriate size (0.1 to 0.2 mm larger than the diameter of the rivet) into the workpiece. -
Page 7: Maintenance
Use a spanner or similar tool to remove the frame head. tCAUTION 2 (P.2) Use a spanner A and spanner B to loosen and remove the jaw case head (AR-011S: jaw case), and then remove the jaw pusher spring, jaw pusher and jaws. AR-011S AR-011M・AR-011H... -
Page 8: Storage
(Refer to pages 6 and 7 “Maintenance”). ¡ To increase the working life of the tool, it is recommended that you give it periodic overhauls. Contact the place of purchase or your nearest “LOBSTER” dealer for any overhauls and repair work required. -
Page 9: Troubleshooting
TROUBLESHOOTING If a problem occurs, check the following. If the problem persists after checking the items in the table below, contact your nearest “LOBSTER” dealer or direct to us. In making any enquires about this product or requests for repair work, first check the troubleshooting items below, and then make a note of the model number, the usage conditions and the trouble symptoms in as much detail as possible. -
Page 10: Ar-011S Parts Table
AR-011S PARTS TABLE... - Page 11 Indicate the tool model, part name, code no. and quantity as shown below when ordering. * When parts are modified for Model Part Name Code No. Qty. improvement, the older parts are kept AR-011S Jaws (pair) ‘S’ 10032 in stock for a period of five years. AR-011S Frame head 10170...
-
Page 12: Ar-011M Parts Table
AR-011M PARTS TABLE... - Page 13 Index No. Part name Code No. Index No. Part name Code No. 1−A 10027 10102 Nosepiece ‘S’ 2.4 (3/32) Air Cylinder 1−B 10028 29736 Nosepiece ‘S’ 3.2 (1/8) Bumper 1−C 10029 10144 3×22 Nosepiece ‘S’ 4.0 (5/32) Spring Pin 1−D 10030 10145 3×18...
-
Page 14: Ar-011H Parts Table
AR-011H PARTS TABLE... - Page 15 Index No. Part name Code No. Index No. Part name Code No. 1−A 10213 10119 Nosepiece ‘M’ 2.4 (3/32) Trigger Lever 1−B 10214 23595 3×7.2 Nosepiece ‘M’ 3.2 (1/8) Spring Pin 1−C 10215 10188 Nosepiece ‘M’ 4.0 (5/32) Air Cylinder 1−D 14350 29736...
- Page 16 ® BE LIABLE FOR DAMAGES OR COSTS INCURRED BY THE BUYER OR SUBSEQUENT USER IN RE- PAIRING OR REPLACING DEFECTIVE GOODS. ROUTINE MAINTENANCE AND REPAIR OF LOBSTER RIVET ® TOOLS CAN BE PERFORMED BY AN AVERAGE MECHANIC. HOWEVER, IF YOU HAVE A LOBSTER RIVET TOOL THAT IS IN ®...
- Page 17 MEMO...
Need help?
Do you have a question about the AR-011S and is the answer not in the manual?
Questions and answers