Ercolina MB-42 Programming Instructions
Hide thumbs Also See for MB-42:

Advertisement

Programming Instructions for Models MB-42, SB-48, TB-60, TB-76 & ERD-3000
1. Switch the power to the (ON) position.
2. The display will read: "Forward C.Bending Die"
3. Depress (CURSOR) button on touch pad. The display will read "Data Entry" Select (+) = YES Depress (+) (PLUS) Display
will now read "P.1" or similar. This number refers to the program number. You may depress (+) (PLUS) button on touch pad to
select the program to edit.
4. Hold (-) (MINUS) key down for five seconds. This erases all data within selected program.
5. Enter a new degree of bend using (+) (PLUS) or (-) (MINUS) keys to enter the desired angle. You may also use pre-set
degree buttons to enter degree of bend.
6. Depress (ENTER) button once to store the bend angle.
7. The display will prompt you to enter another bend angle within the same program. If you desire additional bends within the
same program, you may input them in the same manner. If no additional bends are required depress (ENTER).
8. The display will now indicate the program number you edited. (Example P.1)
9. Depress (ENTER) button again and the display returns to the normal operating screen.
1. Switch the machine to the (ON) position.
The display will read "Forward C. Bend Die" or similar
Mm 000.0 P1.1 090
2. Depress the (MENU) button
The display will read "MAIN MENU"
1 -DATA ENTRY MODE
3. Depress the (ENTER) button
The display will read "GRP RPM" or similar
1
The "GRP" refers to the program number. You may depress the (+) (PLUS) or (-) (MINUS) buttons to change the "GRP" or
program number.
The display will periodically flash the following message:
"TO INPUT DATA PUSH FOR 3 SECONDS"
4. Press the (*) button for 3 seconds once you have selected the desired program number. Display will read "Angle 000 Bend 1."
5. Press the (+) (PLUS) or (-) (MINUS) keys to enter the desired bend angle.
6. Press (ENTER) when finished entering the first bend within the program.
The machine display will prompt to enter another angle within the same program. If you desire additional bends within that "GRP"
or program, you may input them in the same manner as mentioned above.
7. If no additional bends are required, press (ENTER)
The display will momentarily read "END OF DATA ENTRY"
The display will now show "GRP RPM" or similar
1. Load material into former and move counterbending die vise assembly forward until die contacts material.
Note: counter bending die axis is equipped with an encoder. This axis must be set to zero before the
machine will operate. Depress (ENTER) button once to zero this axis. (Note: Always place material
with the weld-seam up to neutralize the seam. Also, the counterbending die needs to be lubricated
using Ercolina® spray grease Part number PAR 811 prior to bending.)
2. Material springback must to be set at this time. Depress (BEND) button on touch-pad or use the (BEND)
pedal until material begins to deflect, refer to diagram. Release the (BEND) button.
3. View LCD display and record angle. The number of degrees it took to make the material deflect is
shown on the display. This value is the material springback. Depress (ENTER) button once and the
program automatically compensates for the springback value.
4. Tighten large socket set screw on the side of the vise assembly until it contacts the back of the sup-
port bracket. The springback value has been set for the first bend within the sequence only. Springback
value must be programmed for each bend within the program.
5. Depress (BEND) button or (BEND) pedal and finish bending process. The machine will automatically stop at programmed
bend angle.
6. Depress (RETURN) button or (RETURN) pedal to return former and material to the starting position.
(563) 391-7700 • (563) 391-7710 Fax •
Warning: read operators manual before attempting to operate machine
(Be sure the machine is connected to a suitable power source before switching power on!)
Programming Instructions for MegaBender® 030
1.52xxxxxxxx
1
1.52xxxxxxxxxxxxxxx

Setting the springback and finishing the bend

Ercolina
Manufacturers of tube, pipe and profile bending machines
3100 Research Parkway • Davenport, Iowa 52806
by CML USA Inc.
®
www.ercolina-usa.com
Beware of Imitations!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MB-42 and is the answer not in the manual?

Questions and answers

Summary of Contents for Ercolina MB-42

  • Page 1 Warning: read operators manual before attempting to operate machine (Be sure the machine is connected to a suitable power source before switching power on!) Programming Instructions for Models MB-42, SB-48, TB-60, TB-76 & ERD-3000 1. Switch the power to the (ON) position.
  • Page 2 Round Tube Tooling Pipe Outside Minimum Wall Former Counter Bend Pipe Outside Minimum Wall Former Counter Bend size Diameter Part# Part# size Diameter Part# Part# Thickness Thickness 1/4” .250 1.4 / 36mm .039 T00-153RO36T0250 T00-154T0250 1-3/4” 1.750 3.9 / 100mm .118 T00-153R100T1750 T00-154T1750...

This manual is also suitable for:

Sb-48Tb-60Tb-76Erd-3000Megabender 030

Table of Contents