Summary of Contents for R2 MT Series
- Page 1 ENGLISH Mill Grader Mod. MT – MTL – MThi - MTLhi Instructions and maintenance manual (Translation of the original instructions) Rev. 27 – 04 – 2016...
-
Page 2: Table Of Contents
Index Pag. Introduction..........................3 Machine identification………………………………………………………………………………... 3 Description of the machine and its proper use.…………………………………………………… Technical specifications and dimensions................. Handling and transportation of the machine………………………………………………………. 5 Accident prevention........................6 Components assembly and coupling of the working equipment………………………………... 7 Preparation for use…………………..................Working depth adjustment………..................... -
Page 3: Introduction
1 – Machine identification Each R2 machine has a CE plate with the main details of the R2 company and of the machines. The plate is positioned on the top center of the machine. -
Page 4: Description Of The Machine And Its Proper Use
-The respect of the rules of use and maintenance established by the manufacturer and gathered in this manual. -the exclusive use of spare parts and original R2 accessories. The machine must be used, maintained and repaired only by competent staff. -
Page 5: Technical Specifications And Dimensions
3 – Technical specifications and dimensions (*note 2 mod. hi) Model MTL 50 MTL 75 MTL 100 MT 60 MT 90 MT 125 Milling width (Fig. 3 – Ref. A) 50 cm 75 cm 100 cm 60 cm 90 cm 122 cm Levelling width (Fig. -
Page 6: Accident Prevention
16. Always read the instruction booklet of the working equipment (walking tractor or tractor) before fitting and using the R2 machine.Do not remove or evade the security systems of the working equipment; before start working, be sure that the security systems of the walking tractor or tractor work correctly;... -
Page 7: Components Assembly And Coupling Of The Working Equipment
6- Components assembly and coupling of the working equipment. (*note 5 mod. hi) Note: all the components that make part of the machine and that must be assembled before using it, have been designed to minimize the user’s work ; the parts should be assembled using hand tools (wrenches). -
Page 8: Preparation For Use
7 – Preparation for use Before using the machine it is necessary to perform the following controls with the walking tractor or tractor off and the key off: - Check that the lubricant is at the indicated level. - Check the bolts tightening and that all the elements are in perfect conditions. - Check that the signs security are present and legible. -
Page 9: Machine Use
10 – Machine use (*note 7 mod. hi) 10.1 – Soil working Once you have made the adjustments, it is possible to operate the walking tractor (or tractor) and so the PTO that will determinate the hoes rotation . Pressing the forward, the working soil will start. The operator’s position is at the rear of the walking-tractor (or semi-laterally where it is possible to adjust the handlebars) or at the driver’s tractor seat.It is important to remember that while driving you should not make any turning maneuvers (the hoes are inserted into the ground) but only small... -
Page 10: Maintenance
11 - Maintenance (*note 8 mod. hi) Operations to be carried out in order to maintain the machine in good working conditions: Before using the machine: 1. Check the clamping of the walking tractor tie-rods on the machine flange. 2. Check that the screws are tight, in particular check that the hoes screws are intact, if while working they break, it is necessary to stop working and replace them. -
Page 11: Hoes Replacement
12 – Hoes replacement The hoes replacement must be made disassembling the roller group and placing the machine on the back side so that the hoes are parallel to the ground. Place the machine on a stable and safe plane. When mounting the new hoes, be sure that the clamping nut fits well in its seat (Fig. 8 Ref. B);... -
Page 12: End Of Work And Storage Of The Machine
13 – End of work and storage of the machine If the MILL GRADER Mod. MT – MTL – MThi - MTLhi must remain unused for a long period, it is necessary to perform the following steps: 1. Wash thoroughly the MILL GRADER Mod. MT – MTL – MThi - MTLhi and then dry it. 2. -
Page 13: Specific References For The Hydraulic Machines
NOTE: the following data which concerns to the engine specifications are given by the manufacturer of the hydaulic motor; for the specifications of the engine application to the R2 machine look at the previous table and to the considerations of the following notes. - Page 14 When the Mill Grader R2 is disconnected from the tractor , it is recommended to place the protective taps on the pipe fittings. When the Mill Grader R2 is connected to the tractor, the caps remain attached through a ring to the hoses, so that they can be repositioned next time.
- Page 15 Screw the hoses to the engine and fit them through the quick coupling to the feed circuit and tractor drain (Fig. 11). Note: the Mill grader R2 can work in both sense of rotation. Always wear gloves and protective glasses.
- Page 16 (*note 6 mod. hi) Adjust the working depth using the screw crank (*note 7 mod. hi) (*note 8 mod. hi) General rules for the hydraulic motor use: Working oil temperatures in the hydraulic system should be kept between +30°C and +60°C. The anti-wear and lubrication properties of the oil are greatly reduced at higer temperatures.
-
Page 17: Guarantee And Certification
- When the equipment is not used in accordance with the manual instructions. - When the equipment has been used incorrectly. The R2 Company reserves the right to modify the data in this manual whenever this is considered necessary for technical or commercial improvements regarding the product itself. - Page 18 NOTE...
- Page 20 R2 Rinaldi S.r.l. Via degli Artigiani, 23 40024 – Castel San Pietro Terme Bologna (ITALY) Tel. (0039) 051.94.30.42 Fax (0039) 051.69.42.086 www.R2RINALDI.com R2@R2RINALDI.com...