Nortek DOOR GARD Programming Manual

Advertisement

Quick Links

Features and Programming Guide
DOOR♦GARD
keypads offer fi eld proven reliability and cost effective solutions anywhere limited control or access is desired.
Designed for individual control of up to four devices, Door  ♦   G ard keypads are the perfect choice for controlling electric locking
devices, security systems, automatic operators or machinery. Door  ♦   G ard keypads accept power from a 12 or 24 Volt AC/DC
supply.

FEATURES

4 INDEPENDENT OUTPUTS
4 INDEPENDENT TIMERS
ALL OUTPUTS ASSIGNABLE BY CODE
ON BOARD MAIN RELAY
120 USERS
REMOTE TRIGGERING INPUT
KEYPAD PROGRAMMABLE

MEMORY

Non-volatile EEPROM memory means your codes and
instructions will be there whether you remove power for
5 minutes or 5 years.
All programming is done entirely from the front of the
keypad. LED or sounder guidance makes programming
easy. It takes seconds for an authorized user to change

codes.

CODES
The Door  ♦   G ard keypads allow up to 120 individual user
codes. Codes can be 1 to 6 digits in length and digits may be
repeated. The Master Code is always stored in user location
one (1).

MAIN RELAY

The main relay is a form C relay, which you can program as
a timed output (1 to 90 seconds) or to toggle (latch). See the
Wiring Diagram and Specifi cations for the relay electrical
specifi cations.

AUXILIARY OUTPUTS

You can program these outputs as timed outputs (1 to
90 seconds) or to toggle (latch). They can be controlled
individually or in combination by a code. Some models
have 1 Amp form C relays and other models have negative
voltage outputs with a 50mA sink. ‡
6-050212 X2
Access Control Keypads
Features and Programming Guide
Note: This product is designed to be installed and serviced
by security and lock industry professionals.

PANIC

Panic is activated by pressing the ✱ and # keys at the same
time. By default, it operates output 4 and activates for 1
second.

REMOTE TRIGGERING INPUT (REX)

By default, upon a momentary closure this normally open
loop triggers the main relay for the same time period as the
Master Code. You can also program the REX to operate any
combination of the available outputs. The auxiliary outputs
activate for their programmed time.

KEYPRESS FEEDBACK/AUDIBLE KEYPRESS

Door  ♦   G ard keypads, by default, acknowledge a keypress
by momentarily illuminating the yellow LED or activate the
sounder. This depends on the model. You can turn this off
through programming.

KEYPAD ACTIVE OUTPUT

Door  ♦   G ard keypads can be programmed to energize a
voltage output whenever a key is touched. You can use this
to turn on lights, CCTV camera, or notify a guard.

AUTO ENTRY

This feature is used when you don't want to press the ✱ key
after entering your code. You only need to enter your code
number (without pressing ✱) and the relay activates. To
use this feature, the user codes must be the same length
as the master code. Please remember to access program
mode when auto entry is on, do not press the ✱ key (Press:
99 # master code), however the ✱ is required while entering
programming commands.
‡ Voltage Outputs may be converted to 1 Amp, Form-C
relays by adding the 293 Auxiliary Relay Board (Model
# 0-219000).
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DOOR GARD and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Nortek DOOR GARD

  • Page 1 Features and Programming Guide Access Control Keypads Features and Programming Guide Note: This product is designed to be installed and serviced by security and lock industry professionals. DOOR♦GARD keypads offer fi eld proven reliability and cost effective solutions anywhere limited control or access is desired. Designed for individual control of up to four devices, Door ...
  • Page 2: Testing The Keypad

    Features and Programming Guide TESTING THE KEYPAD PROGRAMMING 1. Connect the positive (+) lead of your power supply to 1. Enter programming mode Indicator Press 99 # (master code) ✱ the terminal strip (TS1) V+ input. Flash/Beep Slowly 2. Connect the negative (-) lead of your power supply to 2.
  • Page 3 Features and Programming Guide PROGRAMMING OPTIONS CHART If the pre-programmed default values must be changed or additional functions are desired, the following options may be programmed. Press 99 # (master code) ✱ 1. Enter programming mode Press (time) # 1 # (new code) ✱ (new code) ✱ 2.
  • Page 4 There are no obligations after troubleshooting, please call the Technical Services or liabilities on the part of Nortek Security & Control LLC department at 1-800-421-1587. for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profi...

Table of Contents