Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vanderbilt CHSM2210
Summary of Contents for Vanderbilt CHSM2210
- Page 1 CHSM2210/2211 Medium Camera Housing Installation Guide...
- Page 2 Data and design subject to change without notice. / Supply subject to availability. © 2016 Copyright by Vanderbilt We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.
-
Page 3: Table Of Contents
Cable entry into the camera housing ............14 Fitting the camera and lens ..............14 Mounting the camera housing assembly ..........15 Connecting to the power supply .............. 16 Adjusting the sunshield ................17 Maintenance and service ..............18 Disposal ....................18 © Vanderbilt 2016... -
Page 5: Safety
The fuse for the device and the fuse for the electrical system of the building must be installed separately. Risk of cable damage due to stress Use only cable types that are approved for the environmental requirements. The cable glands used must be appropriate for the cable diameter. © Vanderbilt 2016... -
Page 6: Meaning Of The Signal Words
Type of hazard CAUTION There is a risk of minor to medium injuries or damage to property IMPORTANT Malfunctioning may result Meaning of the hazard symbols The nature of the hazard is indicated by icons. Warning of a hazard © Vanderbilt 2016... -
Page 7: Eu Directives
EN 61000-3-2 EN 61000-3-3 EN 55022 Class B Resistance to interference: EN 50130-4 EU Directive 2006/95/EC “Low-Voltage Directive” Compliance with the European Directive 2006/95/EC has been proven by testing according to the following standard: Safety: EN 60950-1 © Vanderbilt 2016... -
Page 8: Technical Data
End caps: Polyester powder coat, RAL7016 Grey Internal Dimensions (L x W x H) 300 x 85 x 85 mm Weight 2.5 kg Suitable Pan and Tilt Units CDD2425, CDD2416-T, CDAP2316-T, CDAP2416-T Suitable Brackets CHBS2815, CDBS4540 + CAHA1040 © Vanderbilt 2016... -
Page 9: Mechanical Dimensions
66 mm 133 mm 76 mm 125 mm Key to parts Fig. 2 Key to parts Front End Cap Cable Anchors Housing Body Terminal Board Sunshield Camera Mounting Slot Rear End Cap Demister Assembly Cable Glands Window © Vanderbilt 2016... -
Page 10: Scope Of Delivery
Shoulder washer (to insulate screw from camera mounting plate) NOTE The complete assembly should be mounted and tested in the workshop prior to use on-site. Accessories Type Designation CAPD1210-C230 12 V DC 500 mA PSU 230 V AC input © Vanderbilt 2016... -
Page 11: Installation
M4 screws which secure the housing to the rear cap should be retightened to a torque of 2 Nm. Fig. 3 Inside the housing enclosure Sun Shield Demister Termination Board Cable Anchor Rear Cap Camera Mounting Plate Housing Cover © Vanderbilt 2016... -
Page 12: Fitting The Power Supply Modules
Installation Fitting the power supply modules In some installations the camera requires a 12 V DC power supply; Vanderbilt power supply module CAPD1210-C230 is available and mounts inside the rear end cap (see Fig. 4). It is fused by connecting it through the terminal board. To fit the... - Page 13 PSU module output cable to camera supply terminals PSU module input cable ‘Fused output’ terminals Ensure all SELV and signal wiring is kept away from live parts and is suitably IMPORTANT protected from live parts by double insulation. © Vanderbilt 2016...
-
Page 14: Cable Entry Into The Camera Housing
Adjust the camera position before you fully tighten the mounting screw. Connect power to the camera as described in Section 5.6. © Vanderbilt 2016... -
Page 15: Mounting The Camera Housing Assembly
Position the assembly as required to obtain the desired video image. Ensure all fasteners are tightened correctly, use anti-vibration fixings where necessary. Fig. 7 Mounting the camera housing assembly Rear end cap Compression glands 4 M6 tapped holes on 101.6 mm (4”) PCD Compression glands © Vanderbilt 2016... -
Page 16: Connecting To The Power Supply
CAUTION building installation, protect the unit via a fuse or circuit breaker rated at 2 A for CHSM2210 110 – 230 V AC units and 5 A for CHSM2211 12 – 24 V AC units. NOTE Use only cable suitable for the application and that meets the standards required by the installation. -
Page 17: Adjusting The Sunshield
Installation Adjusting the sunshield Firmly squeeze (A) the sides of the sunshield (See Fig. 9). Slide (B) the sunshield to the required position. Release the sunshield and it will remain in position. Fig. 9 Sunshield adjustment © Vanderbilt 2016... -
Page 18: Maintenance And Service
Neither do they constitute or amend any earlier or existing commitment or legal relationship. All obligations on the part of Vanderbilt result from the relevant purchase agreement which also contains the complete and solely valid warranty regulations. This installation guide neither extends nor restricts these contractual warranty regulations. - Page 20 Issued by Vanderbilt © Vanderbilt 2016 Clonshaugh Business and Technology Park Data and design subject to change without notice Clonshaugh Supply subject to availability Dublin 17 Document no.: C-301053 Ireland Document version: 2.0 www.vanderbiltindustries.com Edition:23/05/2016...
Need help?
Do you have a question about the CHSM2210 and is the answer not in the manual?
Questions and answers