Advertisement
Model No. : UT-1404
CLEAN ROOM INDICATOR TEMP+HUMIDITY (RH)
Sure for service with hi-end
Sure for service with hi-end
Add.-78/1/Z/3, Makarpura GIDC, Makarpura, Vadodara
Sales:
+91 94273 01436
z
OPERATION MANUAL
Model No. : UT-1404
22.3
LO
HI
35.8
LO
HI
UP/ACK.
PASS
Website:
www.utplindia.in
B C
%
COM.
ENTER
MODE
Uni
Uni
versal
versal
Tech
Tech
nology
nology
Ph
:
+91 7046223333
z
E-mail :
sales@utplindia.in
COM
AL 1
Advertisement
Table of Contents
Related Manuals for Unitech UT-1404
Summary of Contents for Unitech UT-1404
- Page 1 Model No. : UT-1404 OPERATION MANUAL CLEAN ROOM INDICATOR TEMP+HUMIDITY (RH) Model No. : UT-1404 22.3 35.8 AL 1 COM. ENTER MODE UP/ACK. PASS Sure for service with hi-end Sure for service with hi-end versal versal Tech Tech nology nology Add.-78/1/Z/3, Makarpura GIDC, Makarpura, Vadodara...
- Page 2 REGISTER ADDRESS FOR MODBUS INTRODUCTION The UNITECH “HVAC TEMP+RH Indicator : UT-1404” is specially designed to indicate the Room Temp & HUMIDITY of process areas. The large 3 digit, 1.0” high LED display is easy to read, even from a...
-
Page 3: Front Panel Description
Model No. : UT-1404 PAGE : 1 FRONT PANEL DESCRIPTION 22.3 35.8 COM. KEY PAD ENTER MODE UP/ACK. PASS NO DISPLAY DESCRIPTION Seven Segment LED displays of Temp & RH Red LED will glow on low Process values of ºC,%Rh High Red LED will glow on high Process values of ºC,%Rh. -
Page 4: Technical Specification
Model No. : UT-1404 PAGE : 2 TECHNICAL SPECIFICATION FDA 21 CFR part 11 - GAMP-4 compatible. Microcontroller based indicator with inbuilt Temperature & RH measurement in single enclosure. Incorporates highly stable built-in or Remorte Temp.+ RH sensor. 3 Digit, 0.80" bright LED display for displaying RH & Temperature. -
Page 5: Installation
Model No. : UT-1404 PAGE : 3 INSTALLATION Terminal Detail CAUTION WIRING CONSIDERATION SHIELDED TWISTED PAIR WIRE IS USED FOR ALL ANALOG I/P, PROCESS SENSORS, RTD, THERMOCOUPLE, DC mV-mA, VOLT DC, LINEAR INPUT AND COMMUNICATION SUPPLY COMM. FAILURE TO COMPLY WITH THESE INSTRUCTION MAY RESULT... -
Page 6: Programming Flow Chart
Model No. : UT-1404 PAGE : 4 PROGRAMMING FLOW CHART Configuration Setup Change Mode Selection Mode Mode Password Mode 03.0 Any New Password 00.2 05.0 00.2 03.0 00.0 00.2 05.0 10.0 00.2 1.00 00.0 10.0 Sure for service with hi-end... -
Page 7: Configuration Mode
Model No. : UT-1404 PAGE : 5 CONFIGURATION MODE This Mode is used to change Alarm and Communication Operation Configuration CONFIGURATION MODE PARAMETER Description Range Parameter Default Value Password for Parameter Setting Scroll the digit by key, increase by key. -
Page 8: Setup Mode
Model No. : UT-1404 PAGE : 6 SETUP MODE This Mode is used to Setting the instrument Parameter. To set zero span value, alarm set points with hysteresis, offset etc. SETUP MODE PARAMETER Range Description Parameter Default Value Password for Parameter Setting... - Page 9 Model No. : UT-1404 PAGE : 7 Description Range Parameter Default Value Zero Value. [Temp] 00.0 Values between /99 to 999 Scroll the digit by key, increase by key. 00.0 System Value, don’t change. Span Value. [Temp] 10.0 Values between /99 to 999...
-
Page 10: Error Message And Troubleshooting
Model No. : UT-1404 PAGE : 8 CHANGE PASSWORD MODE CHANGE PASSWORD PARAMETER Range Description Parameter Default Value Old Password. Scroll the digit by key, increase by key. Values between 000 to 999 0000 Existing Password New Password. Scroll the digit by key, increase by key. - Page 11 Model No. : UT-1404 PAGE : 09 REGISTER ADDRESS FOR MODBUS RTU PROTOCOL SR N O P A RA M ETERS A BSO LUTE A DDRESS A CCESS TY P E TEM P . P RO CESS VA LUE 40001...
Need help?
Do you have a question about the UT-1404 and is the answer not in the manual?
Questions and answers
off set is not showing display
The exact reason for the display not showing on the Unitech UT-1404 is not provided in the available information. However, possible causes could include no power supply (device requires 24VDC), wiring issues, or internal faults.
This answer is automatically generated