Table of Contents
Advertisement
Quick Links
19" LCD Color Monitor
Service
Service
Service
Description
Table Of Contents.....................................................1
Revision List................................................................2
Important Safety Notice.............................................3
1. Monitor Specifications..............................................4
2. LCD Monitor Description..........................................5
3. Operation instructions.............................................6
3.1General Instructions........................................6
3.2 Control buttons...............................................6
3.3 Adjusting the Picture...............................................8
3.4 Connecting to the PC ........................................10
4. Input/Output Specification......................................11
4.1 Input Signal Connector.........................................11
4.2 Factory Preset Display Modes...............................12
4.3 Pixel Defect Policy..........................................13
4.4 Failure Mode Of Panel ....................................16
5. Block Diagram.................................................17
5.1 Software Flow Chart.............................................17
5.2 Electrical Block Diagram....................................19
6. Schematic Diagram.............................................21
6.1 Main Board....................................................21
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN
SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Copyright 2008 Philips Consumer Lifestyle
Page
Page
SAFETY NOTICE
Subject to modification ○
190B9CS/00
190B9CB/00
190B9CB/27
190B9CB/75
190B9CB/69
Description
6.2 Power Board.....................................................26
6.3 Key Board.........................................................29
6.4 USB Board......................................................30
7. PCB Layout...........................................................32
7.1 Main Board............................................................32
7.2 Power Board........................................................34
7.3 USB Board....................................................36
7.4 Key Board.........................................................36
8. Wiring Diagram...................................................37
9. Scalar Board Overview...........................................38
10. Mechanical Instructions.........................................39
11.Trouble shooting..............................................43
12. Repair Flow Chart...............................................45
13. ISP Instructions......................................................51
14. DDC Instructions...................................................58
15. White Balance, Luminance Adjustment..................68
16. Monitor Exploded View.........................................70
17. Recommended & Spare Parts List............................71
18. Different Parts List...............................................74
19. General Product Specification................................76
Jun, 11, 2008
K
Chassis: HUDSON 9
Page
GB
312278518060
Advertisement
Chapters
Table of Contents
Related Manuals for Philips 190B9CS/00
Summary of Contents for Philips 190B9CS/00
-
Page 1: Table Of Contents
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES Copyright 2008 Philips Consumer Lifestyle Subject to modification ○ Jun, 11, 2008 312278518060... -
Page 2: Revision List
HUDSON 9 Revision List Version Release Date Revision History Jun.11, 2008 Initial release, Draft Version Jun.30.2008 Add CTV Model 190B9CB/75 and 12NC for 190B9CB/75 July.04.2008 Add CTV Model 190B9CB/69 and 12NC for 190B9CB/69... -
Page 3: Important Safety Notice
HUDSON 9 Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Philips Company Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. -
Page 4: Monitor Specifications
HUDSON 9 Monitor Specifications... -
Page 5: Lcd Monitor Description
HUDSON 9 2. LCD Monitor Description The LCD monitor will contain a main board, a power board, a USB board and a key board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage. -
Page 6: Operation Instructions
HUDSON 9 3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at the front of the panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. - Page 7 HUDSON 9 Rear View...
-
Page 8: Adjusting The Picture
Description of the On Screen Display On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window. A user friendly on... - Page 9 HUDSON 9 The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on.
-
Page 10: Connecting To The Pc
HUDSON 9 3.4 Connecting to the PC 1) Connect the power cord to the back of the monitor firmly. (Philips has pre-connected VGA cable for the first installation.) Available for selective models Available for selective models 2) Connect to PC (a) Turn off your computer and unplug its power cable. -
Page 11: Input/Output Specification
HUDSON 9 4. Input/ Output Specification 4.1 Input Signal Connector Analog connectors Pin No. Description Pin No. Description Red video input DDC +5V Green video input/SOG Logic Ground Blue video input Ground Sense (GND) Serial data line (SDA) Cable detect (GND) H. -
Page 12: Factory Preset Display Modes
HUDSON 9 4.2 Factory Preset Display Modes... -
Page 13: Pixel Defect Policy
HUDSON 9 4.3 Pixel Defect Policy... - Page 14 HUDSON 9...
- Page 15 HUDSON 9...
-
Page 16: Failure Mode Of Panel
HUDSON 9 4.4 Failure Mode Of Panel Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical Polarizer has bubbles instruction on this manual to eliminate failure by replace LCD panel. -
Page 17: Block Diagram
HUDSON 9 5. Block Diagram 5.1 Software Flow Chat... - Page 18 HUDSON 9 1) MCU initialize. 2) Is the EPROM blank? 3) Program the EPROM by default values. 4) Get the PWM value of brightness from EPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode.
-
Page 19: Electrical Block Diagram
HUDSON 9 5.2 Electrical Block Diagram 5.2.1 Main Board Panel Interface (CN403) Scalar NT68667FG EEPROM Keypad Interface (Include MCU, ADC, OSD) M24C16 (CN402) (U401) (U403) H sync D-Data V sync D-Clock D-Sub Flash Memory Crystal Connector Connector PM25LV010A-100SCE 12MHz (CN102) (CN101) (U402) (X401) - Page 20 HUDSON 9 5.2.2 Inverter/Power Board AC input Bridge Rectifier Transformer Rectifier diodes EMI filter and Filter Start Circuit: R904、R905 CN902 Feedback Circuit Control IC ON/OFF Output MOSFET Transformer Circuit Lamp Over Voltage Feedback ON/OFF Circuit Control IC Control...
-
Page 21: Schematic Diagram
HUDSON 9 6. Schematic 6.1 Main Board 715G3108 1 TSUM16FWR SCHEMATIC XGA/SXGA LVDS OUTPUT DSUB_R+ DSUB_R+ VCC1.8 DSUB_R- DSUB_R- DSUB_G+ DSUB_G+ VCC3.3 DSUB_G- DSUB_G- VCC1.8 DSUB_SOG DSUB_SOG CMVCC DSUB_B+ DSUB_B+ DSUB_5V DSUB_B- DSUB_B- VCC3.3 CMVCC1 DSUB_H DSUB_H CMVCC1 DSUB_V DSUB_V DSUB_5V DDC1_SDA DDC1_SDA... - Page 22 HUDSON 9 POWER field CN701 A1 C701 B2 C702 C1 C703 A2 5VCC C704 B5 CN701 C705 B5 C706 C4 SM340A 5VCC C707 C5 D701 C708 C4 R701 C709 C4 BKLT-VBRI C710 A2 BKLT-EN C711 B4 R710 PANEL_ID# D701 A2 R703 4K7 1/16W 5% Volume#...
- Page 23 HUDSON 9 FB102 INPUT CN101 A2 VGA_B+ R105 100R 1/16W 5% C102 CN102 B1 DSUB_B+ BEAD 0.047uF C101 B3 H_Sync R102 0R05 1/10W 5% R103 1K 1/16W 5% DSUB_H C102 A5 V_Sync R104 1K 1/16W 5% R108 C105 DSUB_V C103 A2 5pF/50V E5VCC 75R 1/16W 5%...
- Page 24 HUDSON 9 SCALER FB401 FB406 FB403 AVCC PVCC VCC1.8 CVDD 300OHM 300OHM 300OHM DVDD C440 C403 C404 C448 C406 C407 C442 C401 R414 U402 1uF 16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.22uF16V 10K 1/16W 5% SPI_CE VCC3.3 SPI_SO HOLD# R409 100R 1/16W 5% SPI_CK...
- Page 25 HUDSON 9 OUTPUT CN301 CN301 A5 C301 C4 C302 B3 C303 C3 C304 C2 C305 C3 C306 C2 Q301 B3 Q302 C2 TCLK1M TCLK1P R301 C4 R303 B2 R304 B2 R305 C3 R306 C1 R307 C1 TCLK2M TCLK2P R303 C302 10K 1/16W 5% 0.1uF/16V R304...
-
Page 26: Power Board
Hunson9 6.2 Power Board 715G2986 I 2 POWER BD901 A1 CN901 D1 IC901 B2 CN902 C3 C900 IC903 B3 IC904 C3 C901 C902 L902 L903 C903 C905 L904 L905 C906 C907 L906 NR901 C1 C908 C909 Q901 Q903 C910 C912 R901 R902 C913... - Page 27 HUDSON 9 INVERTER C813 R812 100pF 50V C819 47pF/3KV NC 12K 1/8W CN801 CONN Q805 +12V ON/OFF ZD802 RLZ5.6B ZD803 C814 R817 100pF RLZ5.6B PT801 C820 R813 1K 1/8W C823 AM4502C-T1-PF POWER X'FMR 11K OHM 1/8W R803 R804 0.1uF CN802 47pF/3KV NC 5K1 1/8W 5% 5K1 1/8W 5%...
- Page 28 HUDSON 9 AUDIO CN601 CN602 CN603 C601 C602 C603 C604 C606 C608 C609 C610 C611 C612 C613 C615 C616 FB602 +5V1 IC601 Q608 RJ610 R601 R602 R603 +5V1 R604 R605 +5V1 C604 R606 R607 R602 100uF/25V R608 R609 10K 1/10W 5%(NC) R610 R612 R615...
-
Page 29: Key Board
HUDSON 9 6.3 Key Board 715G3111 1 CN111 POWER KEY1 KEY2 CONN C130 C131 C132 1UF10V 1UF10V 1UF10V KEY1 KEY2 POWER R154 R153 R152 R151 R150 SW101 KEY-LF KEY-AUTO KEY-DOWN KEY-UP KEY-MENU KEY-POWER... -
Page 30: Usb Board
HUDSON 9 6.4 USB Board 715G3114 1 USB PLUG CN713 USB CONN V TYPE L701 120OHM CN712 L702 120OHM C720 CONN 0.001uF... - Page 31 HUDSON 9 HeadPhone&light sensor L704 CN711 HP_R CN710 120 OHM HP_SENSE L705 L703 PHONEJACK HP_L CONN 120 OHM 120OHM...
-
Page 32: Pcb Layout
HUDSON 9 7. PCB Layout C101 C102 C103 C104 7.1 Main Board C105 C106 C107 C108 C109 C110 C111 C112 715G3108 1 C113 C114 C115 C117 C118 C119 C120 C301 C302 C303 C304 C305 C306 C401 C403 C404 C406 C407 C410 C411 C412... - Page 33 HUDSON 9...
-
Page 34: Power Board
HUDSON 9 7.2 Power Board 715G2986 I 2 BD901 C604 C615 C616 C804 C819 C820 C821 C822 C900 C901 C902 C903 C905 C906 C908 C913 C915 C916 C917 C918 C920 C921 C934 C939 CN601 CN602 CN603 CN801 CN802 CN803 CN804 CN901 CN902 D900... - Page 35 HUDSON 9 C601 C602 C603 C606 C608 C609 C610 C611 C612 C613 C801 C802 C803 C805 C806 C807 C808 C809 C810 C811 C812 C813 C814 C815 C816 C817 C818 C823 C907 C909 C910 C912 C924 C928 C929 C930 C931 C932 C935 D801 D802...
-
Page 36: Usb Board
HUDSON 9 7.3 USB Board 715G3114-1 7.4 Key Board 715G3111-1... -
Page 37: Wiring Diagram
HUDSON 9 8. Wiring Diagram Panel 89G179E30NA08 FFC Cable 30 Pin CN301 CN902 CN802 CN801 Main Board Power Board CN701 NT68667FG U401 Speaker R/L CN803 CN402 CN804 AC IN CN603 CN102 CN101 CN711 24Pin USB Board D-SUB CN901 CN601 CN602 4 Pin 4 Pin Key Board... -
Page 38: Scalar Board Overview
HUDSON 9 9. Scalar Board Overview DC-DC Converters EEPROM Flash ROM NOVATEK chip D-SUB D-SUB... -
Page 39: Mechanical Instructions
HUDSON 9 10. Mechanical Instructions 1. Back View as Fig1 Place the monitor face down on a smooth surface as Fig 1. Be careful to avoid scratch and injury during the uninstallation. Fig1 2. Remove the hinge as Fig2. Remove the four screws remarked in red to remove the stand-base ass'y as Fig2. Fig2... - Page 40 HUDSON 9 3. Remove bezel and rear cover as Fig3~ Fig4. Fig3 Fig4...
- Page 41 HUDSON 9 4. Remove main frame cover as Fig5~Fig7. a. Remove the two screws marked in red as Fig5. b. Disconnect the four connector marked in blue as Fig5. c. Remove the two screws marked in red as Fig6. d. Remove the four screws marked in red as Fig7. Fig5 Fig6...
- Page 42 HUDSON 9 Fig7 5. Remove power board and main board as Fig8. a. Remove the three screws marked in red as Fig8. b. Disconnect the connector marked in blue as Fig8. Fig8 6. Remove USB board as Fig9. Remove the two screws marked in red as Fig9.
-
Page 43: Trouble Shooting
HUDSON 9 11. Trouble Shooting This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. Adjust blue “power on” light... - Page 44 HUDSON 9...
-
Page 45: Repair Flow Chart
HUDSON 9 12. Repair Flow Chart 12.1 Main Board (1). No Power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the Adapter/Inverter section Measure U703 PIN2=3.3V Check C706 and C708 X401 oscillate waveforms... - Page 46 HUDSON 9 (2). No Picture No picture The button if X401 oscillate Replace X401 under control waveform is normal Check reset circuit of Check Correspondent component U401 is normal Measure U703 PIN2=3.3V Replace U401 Check C706 and C708 X401 oscillate waveform is normal Replace X401 Check HS VS from...
- Page 47 HUDSON 9 (3). White screen White screen Measure Q302 base X401 oscillate waveform is normal is low level? Replace X401 Check Q302, Q301 is broken or CN301 solder? Check reset circuit of U401 is normal Check Correspondent Check Correspondent component. component.
- Page 48 HUDSON 9 11.2. Power/Inverter Board (1) No power Check CN902 Pin7 = 12V Check AC line volt 110V or 220V Check AC input Check the voltage of C905 (+) Check bridge rectified circuit and F901 circuit Check start voltage for the pin8 of IC901 Check R904, R905 and Change IC901 Check the auxiliary voltage is bigger than 11V and smaller than 25V...
- Page 49 HUDSON 9 (2) W / LED, No Backlight Check CN902 Pin7 = 12V Check adapter or MB Check ON/OFF signal Check Main Board Check IC801 PIN11=5V Check R802 Check IC801 PIN8, 9 or PIN6, 10 have the output of square Change IC801 Check Q805 and Q806 PIN5, 6, 7, 8 have the output of square wave at short time.
- Page 50 HUDSON 9 12.3 Key Board OSD is unstable or not working Is Key Pad Board connecting normally? Connect Key Pad Board Replace Button Switch Is Button Switch normally? Replace Key Pad Board Is Key Pad Board normally? Check Main Board...
-
Page 51: Isp Instructions
HUDSON 9 13. ISP Instruction 1. When do the part, need the tools as follow: a. An i486 (or above) personal computer or compatible. b. Microsoft operation system Windows 95/98/2000/XP. c. “EasyUSB WriterV4.1” program d. Software ISP SN Alignment kits The kit contents: a. - Page 52 HUDSON 9...
- Page 53 HUDSON 9 3. Connect the ISP board as follow: Connect to Connect to the the PC LPT Philips 190B9...
- Page 54 HUDSON 9 4. The process of ISP write is as follows. a. Double-click ，running the program as follows:...
- Page 55 HUDSON 9 b. Click and the program runs as follows: c. Select sure, the picture as below:...
- Page 56 HUDSON 9 d. Click icon and the program runs as follows: e. Click icon, search the program” Philips_190B9_NT68667_HSD190MEN3_A00_V011.hex”, and click open:...
- Page 57 HUDSON 9 f. Click icon. If it burns successfully, it will show as the follow picture:...
-
Page 58: Ddc Instructions
HUDSON 9 14. DDC Instruction General DDC Data Re-programming In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect, repaired monitor’ the serial numbers have to be re-programmed. It is advised to re- soldered the main EEPROM with Software DDC from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed. - Page 59 HUDSON 9...
- Page 60 HUDSON 9...
- Page 61 HUDSON 9 Click to complete the installation. 3. Connect the DDC board as follow: Connect to the PC LPT When you write analog EDID, Connect this port to the Philips 190B9’s VGA port 12V Input...
- Page 62 HUDSON 9 4. Take analog DDC write for example, as f ollow a. Double-click ，appear as follow Figs：...
- Page 63 HUDSON 9 b. Click c. Key 14 numbers in the Serial Number blank, then click “OK”. Now analog DDC Write completes, as follow. Note: The way of digital DDC write is the same as analog DDC write.
- Page 64 HUDSON 9 190B9 EDID Analog 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00 FF FF FF FF FF FF 00 41 0C 6C 08 E8 E0 01 00 16: 17 0D 01 03 0E 26 1E 78 2A A1 50 A3 57 4C 9D 25 32: 11 50 54 BF EF 80 71 4F 81 40 81 80 01 01 01 01 48: 01 01 01 01 01 01 30 2A 00 98 51 00 2A 40 30 70 64: 13 00 78 2D 11 00 00 1E 00 00 00 FF 00 31 32 33...
- Page 65 Detailed Timing: 1280x1024 @ 60Hz. <-x-Detailed Timing Descriptions-x-> <---Detailed Timing Descriptions---> Detailed Timing: FF (Monitor SN) '123132312311' Detailed Timing: FC (Monitor Name) 'Philips 190B' Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min. H. rate: 30KHz Max.
- Page 66 HUDSON 9 Digital 128 bytes EDID Data (Hex): 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00 FF FF FF FF FF FF 00 41 0C 6C 08 58 3D 03 00 16: 1F 0D 01 03 80 26 1E 78 2A A1 50 A3 57 4C 9D 25 32: 11 50 54 BF EF 80 71 4F 81 40 81 80 01 01 01 01 48: 01 01 01 01 01 01 30 2A 00 98 51 00 2A 40 30 70...
- Page 67 <---Detailed Timing Descriptions---> Detailed Timing: 1280x1024 @ 60Hz <-x-Detailed Timing Descriptions-x-> <---Detailed Timing Descriptions---> Detailed Timing: FF (Monitor SN) '123233121231' Detailed Timing: FC (Monitor Name) 'Philips 190B' Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min.
-
Page 68: White Balance, Luminance Adjustment
HUDSON 9 15. White Balance, Luminance Adjustment 1. Apparatuses and program: analyzer CA-210, PC, tool, FGA adjustment program (PHILIPS 190B9.DDCI), Pattern generator. 2. Equipment installation: a. Connect analyzer CA-210 to PC by USB connector, install drive program CA-SDK Ver4.00 for CA-210 and restart PC after finish installing. - Page 69 HUDSON 9 4. Color Temp confirmation Connect the signal to the monitor, the monitor display white-picture, use CA-210 to measure the Color Temp of the screen center and select the OSD to make sure whether the Color Temps accord with the SPEC.
-
Page 70: Monitor Exploded View
HUDSON 9 16. Monitor Exploded View... -
Page 71: Recommended & Spare Parts List
HUDSON 9 17. Recommended & Spare Parts List 190B9CS/00 Item Location Philips 12NC PCM Codes Description Remark FQ106 A34G0810 VOA2B0100 BEZEL L19-8PHA1 FQ405 A33G0441 VOA1L0100 CONTROL BUTTON FQ004 KEPC8QH1 KEY BOARD ASSY FQ401 078G 315 1 V FQ006 USB8QH1 USB BOARD ASSY... - Page 72 HUDSON 9 IC903 056G 139 3A IC PC123Y22FZ0F IC601 056G 616 34 IC APA2069JITUL 2.6W*2 PDIP-16 T901 080GL17T 33 N2 XFMR POWER 550UH YUVA PT801 080GL19T 38 DN X'FMR 103.5UH TK.4305R.101 IC901 056G 379107 IC LD7575A PS SOP-8 IC801 056G 608 12 TEST ONLY IC TA9687GN-A-0-TR SOP-16 IC904 056G 158 12...
- Page 73 HUDSON 9 Service Kit Description Part No. Philips 12NC Remark DDC KIT 715L2005C2 9965 000 43197 FOR ALL MODEL OSD SN KIT 715GT033 C 9965 000 43252 FOR ALL MODEL FOR ALL HUDSON 7 FOR 170A8, 190B8, 150S8, NOVATEK ISP KIT...
-
Page 74: Different Parts List
HUDSON 9 18. Different Parts List Diversity of 190B9CB/00 compared with 190B9CS/00 190B9CB/00 190B9CS/00 Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description E08904 089G 17356X553 AUDIO CABLE 089G 17356X554 AUDIO CABLE FQ103 705GQ834217 BASE ASS'Y 19"PH 705GQ834246... - Page 75 HUDSON 9 Diversity of 190B9CB/75 compared with 190B9CS/00 190B9CB/75 190B9CS/00 Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description FQ301 996500037345 089G412A18NIS3 POWER CORD/32E1818058 089G404A18N IS POWER CORD/32E1818018 FQ103 996510018186 705GQ834217 BASE ASS'Y 19"PH 705GQ834246 BASE ASS'Y 190B9/BW9 VO...
-
Page 76: General Product Specification
4.5 CHECK CROSS TALK (S) 4.6 WHITE COLOR ADJUSTMENT MECHANICAL CHARACTERISTICS 5.1 COSMETIC 5.2 MECHANICAL DATA FILES 5.3 LOCATION OF PHILIPS LOGO 5.4 GAP BETWEEN PANEL AND FRONT BEZEL 5.5 LOCATION OF CONTROL ICONS 5.6 COLOR FOR RESIN/PAINT 5.7 RESINS 5.8 IF RAINT IS USED... - Page 77 6.3 DISPLAY DISTURBANCES FROM EXTERNAL ENVIRONMENT 6.4 DISPLAY DISTURBANCES TO EXTERNAL ENVIRONMENT RELIABILITY 7.1 MEAN TIME BETWEEN FAILURES QUALITY ASSURANCE REQUIREMENTS 8.1 ACCEPTANCE TEST PHILIPS’ FLAT PANEL MONITORS PIXEL DEFECT POLICY 10. REGULATORY COMPLIANCE 10.1 WORLDWIDE REGULATORY 10.2 EMC REQUIREMENTS 10.3 ROHS 10.4 WEEE...
-
Page 78: Foreword
30 minutes that brightness stability is optimal, and follow strictly after panel specification. 2. PRODUCT PROFILE This display monitor unit is a color display monitor enclosed in PHILIPS styling cabinet which has an integrated tilt base. 2.1 LCD Priority : 1. -
Page 79: Scanning Frequencies
HUDSON 9 2.2 Scanning frequencies Hor.: 30 – 83 K Hz Ver.: 56 - 76 Hz Video dot rate: 165 MHz Power input: 90-264 V AC, 50/60 ± 2 Hz Power consumption: 36 W typical without audio 40 Watt typical (with audio) Functions: (1) D-SUB analog R/G/B separate inputs, H/V sync separated, Composite (H+V) TTL level, SOG sync (2) DVI digital Panel Link TMDS inputs... - Page 80 HUDSON 9 Pin assignments: Pin No. Signal Green/ SOG Blue Sense (GND) Cable Detect (GND) Red GND Green GND Blue GND DDC +3.3V or +5V Logic GND Sense (GND) Bi-directional data H/H+V sync V-sync Data clock 3.2.2 DVI Cable The input signals are applied to the display through DVI-D cable. Length : 1.5 M +/- 50 mm Connector type...
-
Page 81: Timing Requirement
HUDSON 9 3.3 Timing requirement Factory Preset mode definition : 1. Perfect FOS (except PHASE) while presenting all required timings. 2. Required timings need to be specified in User's Manual Preset mode definition: 1. Need to support those timings. 2. Perfect FOS after auto adjustment. User mode 1. -
Page 82: Horizontal Scanning
HUDSON 9 62.8 1280x800 74.93 VESA 1280x960 VESA 1280x960 63.981 VESA 1280x1024 60.02 71.691 SUN WS 1280x1024 67.189 DOS/V 1280x1024 79.976 VESA 1280x1024 75.025 81.13 SUN WS 1280x1024 76.11 91.1 VESA 1280x1024 44.772 1280x720 52.5 1280x720 CVT-reduced blanking 1400x1050 1400x1050 91.1 1400x1050 55.469... -
Page 83: Dvi- D Display Identification
Check if the device can work properly. 3.11 DDC/CI SUPPORT 1) Smart control software requirement 2) In accordance with VESA DDC/CI and MCCS ver.2.0, the monitor should be workable with Philips Smart Control and Portrait Display Tune at least. 3.12 EDID 3.13 Hot-key definition... - Page 84 HUDSON 9 3.16.1.1 Position Pressing the “Smart Image” button, the position is in the bottom center of the screen. 3.16.1.2 Smart Image Logo & Banner As design to keep the Light Frame logo at header but change the name to “Smart Image” with bitmap format. 3.16.1.3 Icon of each profile Each profile will use text instead of icon &...
- Page 85 HUDSON 9 B. Entertainment i. Purpose: Design for video application, Like Microsoft Media Player or Real Player. The screen is dominated by video. Ii Enhancement Point: 1. Dynamic contrast enhancement by histogram analysis (DLC) should be implemented. 2. Sharpness enhanced 90%. 3.
-
Page 86: Smart Response (Not Required For This Product)
HUDSON 9 D. Hot keys to trigger: Press [Smart Image] 3 seconds or more to trigger the demo mode. When demo mode is On, press 3 seconds or more to turn off the demo mode. When the demo mode is enabled, the blue LED will flash until demo mode disabled.(N/A for this model) 3.17 Smart Response (Not required for this product) Gray to Gray Response time:? ms (max.) 4. -
Page 87: Mechanical Characteristics
5.1 Cosmetic - Philips ID 5.2 Mechanical data files - ProE files required 5.3 Location of Philips logo - Per Philips make-up sheet 5.4 Gap between panel and front bezel < 0.8 mm (typ) 5.5 Location of Control icons - Per Philips Graphic sheet 5.6 Color for resin/paint -... -
Page 88: Resins
All major plastic parts (bezel, back cover, base) need to be molded from same resin. Plastic resin type selection should be referred to “TY R83-2-9002-1”. 5.11 Texture/Glossing of housing The texture area and texture no should follow Philips make-up sheet. The exterior surfaces shall have a uniform texture. Philips must approve the mold texturing. -
Page 89: Pallet / Container Loading
HUDSON 9 the supplier to the destination specified in the purchase order. All packaging materials are subject to test and evaluation per TYE-M0002. The cushion material shall be constructed using EPS material. 5.16.2 Transportation Test The overall test refers to TYE-M0002. Vibration, drop test should be performed at ambient temperature (20°C to 23oC) and relative humidity (40% to 65%). -
Page 90: Transportation Tests
Control II level AQL: 0.4 (major) 1.5 (minor) (Please also refer to annual quality agreement) Customer acceptance criteria: UAW0377/00 9. Philips’ Flat Panel Monitors Pixel Defect Policy Philips’ Flat Panel Monitors Pixel Defect Policy BRIGHT DOT DEFECTS ACCEPTABLE LEVEL MODEL... - Page 91 HUDSON 9 TOTAL DOT DEFECTS ACCEPTABLE LEVEL MODEL 190B9 Total bright or black dot defects of all type Fig 1: Measurement locations of Brightness Uniformity Fig 2: Cross talk pattern Gray level 46 (64 Gray level)
- Page 92 HUDSON 9 Fig 3: Cross talk Pattern Center at Gray level 0 (Black)
-
Page 93: Regulatory Compliance
HUDSON 9 10. REGULATORY COMPLIANCE 10.1 Worldwide Regulatory International Regulatory Specification COUNTRY DOMAIN SAFETY / EMC / ERGONOMICS / STANDARDS DOCUMENTS IEC60950-1:2001. Group -and national differences of all countries CB Report INTERNATIONAL listed in CB Bulletin No. 107A and CB certificate European Low Voltage Directives 73/23/EEC and 93/68/EEC Declaration of Conformity European... -
Page 94: Emc Requirements
10.2 EMC Requirements Supplier DVT EMI test result must be submitted prior to DVT samples delivery, and PVT EMI test result must be submitted again prior to PVT samples delivery, which also has to meet Philips' immunity testing specification. 10.3 RoHS Restriction on the use of certain hazardous substances. - Page 95 4. When the HV circuitry is operating properly there is no possibility of an x- tube must be the same type as the original, including suffix letter, or a Philips radiation problem. High voltage should always be kept at the manufacturer's approved type.