BRINKS 7166 Installation Instructions

NOTE: IF FOR ANY REASON YOUR PURCHASE OF THIS PRODUCT HAS NOT BEEN A POSITIVE
EXPERIENCE, PLEASE CALL OUR CUSTOMER CARE HOTLINE AT 1-800-562-5625 BEFORE
RETURNING YOUR PRODUCT. WE WANT YOUR FEEDBACK AND AN OPPORTUNITY TO PROVIDE
YOU THE CUSTOMER SERVICE YOU ARE ENTITLED TO WITH OUR PRODUCTS.
Congratulations on your purchase of a Brink's™ Portable Security Lighting xture. You have purchased a safe, dependable, easy-to-install security
lighting system. You can use this xture at home for outdoor lighting applications.
WHAT'S INCLUDED:
A - Light Fixture B - Lamp Hood
D - Mounting Screws (2) E - Wall Anchors (2)
TOOLS REQUIRED:
Screwdriver, Power Drill, 3/16" Drill Bit
PRIOR TO INSTALLATION
Carefully read through the entire installation instructions before installing this security light xture.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODES BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: FIXTURE MUST BE PLUGGED INTO A GROUNDED, OUTDOOR RATED OUTLET THAT MEETS LOCAL, STATE, AND NATIONAL SAFETY CODES. IF YOU ARE NOT FAMILIAR WITH THE SAFETY RATING OF YOUR
OUTLET, IT IS RECOMMENDED THAT YOU SECURE THE SERVICES OF A WELL QUALIFIED ELECTRICIAN WHO CAN ASSURE THE OUTLET MEETS THE LOCAL, STATE, AND NATIONAL SAFETY REGULATIONS REQUIRED.
FIXTURE SHOULD BE MOUNTED ON A WALL AT LEAST 8 FEET
ABOVE THE GROUND FOR OPTIMAL PERFORMANCE.
INSTALLATION INSTRUCTIONS
1. Attach Fixture Mounting Plate (C) at desired location using two Mounting Screws (D). - FIGURE 1
NOTE: Depending on the mounting surface of choice, it may be necessary to use the Wall Anchors (E) with
the Mounting Screws (D).
2. Install the Lamp Hood (B) onto the lampholder.
3. Install two PAR 38 outdoor oodlight bulbs (120 watts max). Position lamp holders downward at a minimum
45º and away from xture housing a minimum of 2 inches.
4. Place Security Light Fixture (A) onto Fixture Mounting Plate (C). - FIGURE 2
5. Plug xture into grounded outlet.
FIXTURE ADJUSTMENT - FIGURE 3
• To rotate lamp head up or down, carefully turn thumbscrew counter-clockwise to release ratchet and allow lamp
head arm to rotate
• Set lamp head to desire location.
• Re-tighten thumbscrew by turning clockwise. Do not over-tighten
MOTION SENSOR CONTROLS - FIGURE 4
Observe the two controls on the bottom of the sensor. The RANGE (sensor sensitivity) control is located on the bottom left.
The ON-TIME (duration) switch is located on the bottom center.
• RANGE (Sensor Sensitivity) - Sets the sensitivity of the motion sensor. Turn the dial clockwise to increase the sensitivity
(range). Turn the dial counter-clockwise to decrease the sensitivity (range). The RANGE control should – in most cases, be set at
the maximum setting. However, the sensitivity (range) may need to be set lower to avoid false triggering (small animals, cars, or
nearby lighting) may require range setting to be dialed down.
• ON-TIME (Duration) - Sets how long the light will stay on after motion is detected (1, 5, or 10 minutes). Slide the ON TIME switch to
the desired time duration. The TEST mode allows the motion sensor to activate during daylight.
SETTING THE MOTION SENSOR CONTROLS
1. Turn the power OFF to the oodlight.
2. Aim the motion sensor to the approximate center of the desired detection range. Caution: Do not aim the sensor above the horizon as
direct sunlight may cause damage to the sensor circuitry.
3. Slide the ON TIME switch to the TEST position.
4. Turn the RANGE control (sensitivity dial) to the full clockwise rotation.
5. Turn the power back ON to the oodlight.
6. Set the RANGE of the motion sensor.
a. Have a person move around at the furthest distance of the desired detection area.
b. If the RANGE dial is at the maximum clockwise rotation and the light still has not turned on, it may be necessary to re-aim the motion
sensor or the desired detection zone may be too far away. The sensor range is designed for up to 70 feet.
c. When the lights do turn on, have the person stand still until the light goes off. Once the lights are off, have the person move again to
con rm the settings.
d. To reduce false triggerings, decrease the RANGE (sensitivity).
7. Slide the ON TIME switch to increase or decrease the time the light stays ON after motion is detected. The setting choices are 1, 5, or
10 minutes. NOTE: When making this adjustment during daylight in test mode, the light will remain ON for the set time duration you
have selected and then turn OFF. Once the light is OFF, it will not turn ON again until motion is detected.
MANUAL OVERRIDE FEATURE
If the security oodlight is connected to an outlet controlled by a wall switch, the Manual Override Feature is available.The Manual
Override Feature allows the unit to be turned ON or OFF manually during the night,bypassing the motion sensor.
MANUAL OPERATION
To manually turn the oodlight ON,turn the wall switch OFF and then ON again immediately within 2 seconds.The oodlights will turn
ON and remain ON until the wall switch is turned OFF.If the wall switch was previously turned OFF for a period of time,turn the wall
switch ON for at least 5 seconds and then use the OFF- ON procedure above to turn the oodlight ON manually.To manually turn the
oodlight OFF, simply turn the wall switch OFF.The unit will not activate as long as the wall switch is in the OFF position.
RESETTING TO AUTOMATIC OPERATION
To return the security oodlight to automatic operation,turn the wall switch OFF for at least 5 seconds and then turn the swith back
ON.The security oodlight will come ONfor the time duration set and then turn OFF.The oodlight will now activate according to the
settings on the motion sensor.Leave the wall switch in the ON position to operate the oodlight in automatic mode.
TROUBLESHOOTING
SYMPTOM
Does not function at all.
Floodlight cycles ON and OFF.
Floodlight is continuously ON.
QUESTIONS: For further assistance or more information,please call 1-800-562-5625,8 am – 5 pm (Paci c Time),Monday – Friday.
LIMITED LIFETIME WARRANTY – This product is warranted to be free from defects in material and workmanship for life of product. If a defect occurs, call 1-800-562-5625 for instructions on how to have defective
product repaired or replaced free of charge. LIMITATIONS - This warranty only covers the assembled lighting products and accessories and is not extended to other components, or equipment used on the product.
Warranty extends to original purchaser of product. Receipt or other approved proof of purchase required for warranty service. NOT LIABLE FOR INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you speci c legal rights, and you may also have other rights
which vary from state to state. NOT COVERED - Product failure not relating to faulty material or workmanship, corrosion of brass components, reimbursement for installation or unauthorized service.
Hampton Products International Corp.
50 Icon, Foothill Ranch, CA 92610-3000 USA
www.hamptonproducts.com • 1-800-562-5625
C - Fixture Mounting Plate
REMEDY
Make sure wall switch (if installed), is ON. Check that the circuit breaker, fuse and main circuit breaker or main power switch are on. Be sure sensor head is pointed downward
towards the target area. Check the bulb(s) for damage.
Redirect security floodlight away from heat sources such as a street, active sidewalk, barbecue grill, etc. Direct floodlight in a slightly different direction than sensor. Turn RANGE
(Sensor sensitivity) control more counterclockwise.
Turn wall switch OFF for at least 5 seconds and then turn switch to ON again. This will reset the fixture to normal (automatic) operations. If there is no wall switch, set circuit
breaker OFF for at least 5 seconds and then turn circuit breaker ON again.
Brink's trademark & copyright work are used with permission.
INSTALLATION INSTRUCTIONS
CORDED 240º MOTION SECURITY LIGHT
IMPORTANT SAFETY INFORMATION
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH ALL APPLICABLE INSTALLATION CODES.
• Before installing this xture, be sure to check with local ordinances regarding approved outdoor lighting.
This xture style may not be allowed in some areas.
• This xture is for outdoor use only.
• This xture is to be connected to a 120 volt, 60 Hz power source. Connecting to a different power source
may create a hazard and will void the warranty.
• Do not use near or around ammable/combustible material or liquids.
• The bulb and xture can get extremely hot during use. Turn off the power and allow the xture to cool
down for at least 20 minutes before working on the unit.
• When replacing the lamp (bulb), use only PAR 38 outdoor oodlight lamp (bulb) - 120 watts maximum in
each lampholder. Lamp holder may say 150W. Never use a lamp (bulb) with a higher wattage than the
stated maximum allowed on the xture. Using a higher wattage lamp (bulb) may cause a re hazard
and/or damage to the unit. Lamps (bulbs) are not included.
• Do not attempt to open the xture housing. There are no serviceable parts inside.
• Always use safety precautions. Safety glasses and gloves should be worn during installation.
• Motion Sensor performance may be affected by temperature.
SAVE THESE INSTRUCTIONS
FIGURE 1
C
E
D
B
Motion Sensor
FIGURE 3
THUMBSCREW
FIGURE 4
RANGE
MIN
RANGE
MIN MAX
MODEL 7166
A
C
ON-TIME
MAX
CDS
10 5 1 TEST
MINUTES
ON-TIME
10 5 1 TEST
MINUTES
Made in China
© 2015 Hampton Products International Corp.
999-61140_7166_REVC 06/15