Advertisement

General Description
This demonstration board utilizes AL3353 to
build a cost effective solution for boost LED
driver.
AL3353 is a LED driver controller designed
for boost converters in a constant frequency
mode. It implements a peak current mode
control scheme and an internal trans-
conductance amplifier to accurately control
the output current over a wide input and
load conditions.
This user guide contains rich information for
the users. A bill of materials is included that
describes the parts used on this board. A
schematic and PCB layout is also included
along with measured system performance
characteristics and test waveforms. These
materials can be used as a reference
design for your products to improve your
product's time to market.
Key Features
1. Wide Input Voltage Range: 20V to 36V
2. Constant Current Mode PWM Controller
3. PWM to Analog Dimming Mode
4. Audio Noise Free
5. Built-in Comprehensive Protections
a)
Under Voltage Lock Out (UVLO)
b)
Over Voltage Protection(OVP)
c)
Over Current Protection(OCP)
d)
Over Temperature Protection (OTP)
e)
LED Open Protection
f)
Output Short Protection
g)
Diode & Inductor Short Protection
h)
LED Cathode Short to GND Protection
6.
Low system BOM cost
Applications
LCD TV
LCD Monitor
Flat Panel Display
AL3353
Mar.2019
www.diodes.com
AL3353EV1 User Guide
High Performance Boost LED Controller
Specifications
Parameter
Input Voltage
Output Power
Output Current
Output Voltage
Efficiency
Dimension
RoHS Compliance
Evaluation Board
Connection Instructions:
DC Positive Input: White Test Point (VIN)
DC Negative Input: Black Test Point (GND)
PWM Signal Input: P1 (PWM)
GND Signal Input: P1 (GND)
Positive Output: Yellow Test Point (LEDA)
Negative Output: Black Test Point (LEDK)
Value
20V ~ 36V
48W
800mA
60V
>90 %
70mm*50mm
Yes
Figure 1: Top View
Figure 2: Bottom View
Page 1 of 9

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AL3353 EV1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Diodes AL3353 EV1

  • Page 1 DC Negative Input: Black Test Point (GND)  LCD TV PWM Signal Input: P1 (PWM)  LCD Monitor GND Signal Input: P1 (GND)  Flat Panel Display Positive Output: Yellow Test Point (LEDA) Negative Output: Black Test Point (LEDK) AL3353 Page 1 of 9 Mar.2019 www.diodes.com...
  • Page 2: Board Layout

    Connect the LED string anode to the test point “LEDA”. Connect the LED string cathode to the test point “LEDK”. Set the PWM signal and turn on the LED power supply. The LED string will light on and output the preset current. AL3353 Page 2 of 9 Mar.2019 www.diodes.com...
  • Page 3: Bill Of Material

    SMD Film Resistor, 10kΩ, ±1% 0805 SMD Film Resistor, 0Ω, ±1% 0805 SMD Film Resistor, 0.4Ω, ±1% R6, R7, R8, R9 1206 SMD Film Resistor, 1.5Ω, ±1% R11, R12, R13 1206 SO-8 IC, AL3353 AL3353 Page 3 of 9 Feb.2019 www.diodes.com...
  • Page 4: System Performance

    LED Open Protection AL3353 monitors the output voltage through the OVP pin. If the LED string is open, the output voltage will exceed the preset level and the converter will be shut down. AL3353 Page 4 of 9 Feb.2019 www.diodes.com...
  • Page 5 Figure 9: LED Cathode Short to GND Protection with 100% Duty Short Protection AL3353 monitors the OVP pin voltage. If V is short, VOVP will drop, and if VOVP drops below 0.25V, the converter will be shut down. AL3353 Page 5 of 9 Feb.2019 www.diodes.com...
  • Page 6 If the LED anode short to LED cathode protection is required, the diode D2 is in need to prevent the FB pin from damaging. A diode should be placed to D2 whose peak repetitive reverse voltage should be no less than 100V and output current should be no less than 2A. AL3353 Page 6 of 9 Feb.2019 www.diodes.com...
  • Page 7: Constant Voltage Mode

    AL3353EV1 constant voltage mode can reach 94% with 24V DC input and 95% with 32V DC input. =24V =32V Load Current(mA) Figure 12: Efficiency vs Load Current Load Regulation =24V =32V Load Current(mA) Figure 13: Output Voltage vs Load Current AL3353 Page 7 of 9 Feb.2019 www.diodes.com...
  • Page 8 800mA, rising slew rate 1A/μs, and from 800mA to 0mA, falling slew rate 1A/μs. When loading, the output voltage drops to 52.75V for a very short time. When unloading, the maximum output voltage is 65.10V. Figure 15: Load Transient with 32V Input AL3353 Page 8 of 9 Feb.2019 www.diodes.com...
  • Page 9 Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages.

Table of Contents