Sony LMT-100 Brochure & Specs page 14

Specifications (SRX-R220/SRX-R210)
SXRD Device Main Specifications
Display device
Size
Resolution
Reflectivity
Contrast
Pixel pitch
Width (between pixels)
Response speed
Liquid crystal mode
Alignment layer
Backplane process
Liquid crystal cell gap
Optical
Projection system
Imaging device
Lamp
Screen coverage
(Approx.)
Light output
* Measured at the screen center of a full pixel size (4096 x 2160) projection with 100 IRE
white and a screen gain of 1.8. A ft-L (foot-lambert) is a unit of measurement for
luminance. One foot-lambert equals 3.4262591 candelas per square meter.
** Tentative
14
SXRD (Silicon X-tal Reflective Display)
1.55-inch across Diagonal
4096 (H) X 2160 (V) Pixels
77%
More than 4000:1
8.5 μm
0.35 μm
5 msec (tr + tf)
Vertical Aligned Mode
Inorganic Thin Film
0.35 μm MOS Process
Less than 2 μm
3-SXRD panel, prism color integrated system
SXRD, 1.55-inch (diagonal),
4096 (H) x 2160 (V) pixels on each chip
SRX-R220: 4.2 kW Xenon lamp x 1
SRX-R210: 3.0 kW** Xenon lamp x 1 or
2.0 kW** Xenon lamp x 1
SRX-R220: 4.5-meter to 20-meter screen width on
Scope size (4.2 kW lamp)
SRX-R210: 4.5-meter to 17-meter screen width on
Scope size (3.0 kW lamp)**
4.5-meter to 14-meter screen width on
Scope size (2.0 kW lamp)**
SRX-R220: 14ft-L on 20-meter wide screen
(4.2 kW lamp)*
SRX-R210: 14ft-L on 17-meter wide screen
(3.0 kW lamp)* **
14ft-L on 14-meter wide screen
(2.0 kW lamp)* **
General
Colorimetry Xenon Color Primaries
White reference Xenon white reference
Contrast Over 2000:1
Input signal Media Block input x 2: 4096 x 2160 pixels
HD-SDI/Dual-link HD-SDI: 1920 x 1080 pixels
(SMPTE-372M/SMPTE-292M/ITU-R.BT709/BTA-S004)
DC-SDI/Dual-link DC-SDI: 2048 x 1080 pixels
12 bit/X'Y'Z'
(with Dual-link HD/DC-SDI Input Board)
DVI-D: XGA (1024x768) / SXGA1 (1280x960) /
SXGA2 (1280x1024) / SXGA+ (1400x1050) /
UXGA (1600x1200) / WUXGA (1920x1200) /
HD (1920x1080) / DC (2048x1080)
Power consumption SRX-R220: 1.2 kW (Single-phase/100-240VAC for
SRX-R210: 1.2kW (Single-phase/100-240VAC for
Power requirements AC 100 to 240 V, 50/60 Hz, single-phase
(for Main power)
AC 200 to 208 V / AC 380 to 415 V,
3-phase(changeable) , 50/60 Hz (for Lamp power)
Operating temperature +5°C to +35°C (+41°F to +95°F)
Storage temperature -20°C to +60°C (+12°F to +140°F)
Operating humidity 35% to 85% (without condensation)
Storage humidity 10% to 90%
Dimensions 740 x 1535 x 1395mm
(W x H x D) (29 1/4 x 60 1/2 x 55 inches)
Mass 300 kg (661 lb 6 oz), without lens and lamp
Fan noise 65 dB or less
Encoding Primaries X Y
R 0.6800 0.3200
G 0.2650 0.6900
B 0.1500 0.0600
X Y
White reference 0.3140 0.3510
main circuit) / 5.2kW (3-phase/
200-208VAC or 380-415VAC selectable
for lamp)
main circuit) / 3.4kW** (3-phase/
200-208VAC or 380-415VAC selectable
for lamp)