Spektrum AS6410NBL Manual

AS6410NBL USB INtErfAcE (SPMA3060)
NOTICE
All instructions, warranties and other collateral documents
are subject to change at the sole discretion of Horizon Hobby,
Inc. For up-to-date product literature, visit horizonhobby.com
and click on the support tab for this product.
Meaning of Special Language
The following terms are used throughout the product
literature to indicate various levels of potential harm
when operating this product:
NOTICE: Procedures, which if not properly followed, create
a possibility of physical property damage AND a little or no
possibility of injury.
CAUTION: Procedures, which if not properly followed,
create the probability of physical property damage AND
a possibility of serious injury.
WARNING: Procedures, which if not properly followed,
create the probability of property damage, collateral
damage, and serious injury OR create a high probability
of superficial injury.
WARNING: Read the ENTIRE instruction manual
to become familiar with the features of the product
before operating. Failure to operate the product correctly
can result in damage to the product, personal property
and cause serious injury.
This is a sophisticated hobby product. It must be operated
with caution and common sense and requires some basic
mechanical ability. Failure to operate this Product in a safe
and responsible manner could result in injury or damage to
the product or other property. This product is not intended
for use by children without direct adult supervision. Do not
attempt disassembly, use with incompatible components or
augment product in any way without the approval of Horizon
Hobby, Inc. This manual contains instructions for safety,
operation and maintenance. It is essential to read and
follow all the instructions and warnings in the manual,
prior to assembly, setup or use, in order to operate
correctly and avoid damage or serious injury.
Age Recommendation:
Not for children under 14 years. This is not a toy.
WARRANTY REGISTRATION
Visit www.spektrumrc.com/registration today to register
your product.
Installing the AS3X
®
Programmer Software
1. Download the AS3X Programmer software from the
SPMA3060 product page at www.HorizonHobby.com.
2. Save the desired AS3X set-up file.
3. Double-click on the .exe file to lauch the software.
Connecting the AS6410NBL
to Your Computer
1. Disconnect the battery from the AS6410NBL.
2. Connect the Spektrum USB Interface to your computer.
™
3. Connect the USB interface to the X-Port slot on the
AS6410NBL.
Activating X-port
X-Port ™ technology must be active to program the receiver.
When X-Port is active, CH5 and CH6 are not available;
however, reversed aileron (CH2) is still available.
1. Ensure the receiver and transmitter are bound.
2. Plug the X-Port accessory or optional servo
into the X-Port/CH5 port.
3. Turn the transmitter on.
4. Move the THRO stick to the full throttle position.
5. Move the control sticks to the corresponding position to
change between the available options (see illustration).
Mode 2 Mode 1
THRO/RUDD ELEV/AILE ELEV/RUDD
CH5/X-port
1. Full THRO
2. Right RUDD
6. Hold this position and plug the battery into the receiver.
7. The LED on the receiver will turn solid within 5 seconds
and the LED will flash 3 times quickly, indicating the
option is now changed.
8. Disconnect the battery from the receiver.
9. Turn the transmitter off.
Programming the AS6410NBL
1. Connect the battery to the AS6410NBL.
2. Start the AS3X Programmer software.
3. Select the desired AS3X set-up file.
4. Select the AS6410NBL mounting orientation.
IMPORTANT: DO NOT disconnect the USB interface or power
off the AS6410NBL during the update process.
5. When the update process is complete, power OFF the
AS6410NBL and disconnect the USB interface.
Sensor/Servo Direction And Compensation
It is extremely important to make sure that the sensors are
compensating in the desired direction prior to the first flight.
IMPORTANT: Be sure the servo is moving in the proper
direction. A right rudder command should move the rudder
to the right (if you're unsure, seek help from someone more
experienced). Reverse the servo direction in the transmitter
if necessary.
Rudder
Pick up the airplane and quickly move the nose to the left.
The rudder should move to the right as shown. If it moves in
the opposite direction, open the Programmer software and
change the sensor direction to the opposite direction.
Right Rudder
Aileron
Pick up the airplane and quickly move the right wing panel
downward. The right aileron should move in the same direction
(down). If it moves in the opposite direction, open the Program-
mer software and change the sensor direction to the opposite
direction.
Up Aileron
Down Aileron
Elevator
Pick up the airplane and quickly move the Nose of the airplane
downward. The elevator should move in the up direction. If it
moves in the opposite direction, open the Programmer software
and change the sensor direction to the opposite direction.
Up Elevator
Initalizing the AS6410NBL
Once the AS6410NBL receiver has been programmed and
the correct sensing direction has been selected, it is very
important to power off the receiver, then power it back on
to initialize the sensors:
THRO/AILE
Place the aircraft on the ground out of the wind and connect
a fully charged flight battery. Ensure the aircraft is immobile
for 5 seconds so the AS3X system initializes correctly.
See the Arming the ESC instructions for correct
connection of the battery to the ESC.
1 yEAr
LIMItEd WArrANty
What this Warranty Covers
Horizon Hobby, Inc., (Horizon) warrants to the original purchaser
that the product purchased (the "Product") will be free from
defects in materials and workmanship for a period of 1 years
from the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmet-
ic damage, (ii) damage due to acts of God, accident, misuse,
abuse, negligence, commercial use, or due to improper use,
installation, operation or maintenance, (iii) modification of or to
any part of the Product, (iv) attempted service by anyone other
than a Horizon Hobby authorized service center, (v) Product not
purchased from an authorized Horizon dealer, or (vi) Product not
compliant with applicable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON
MAKES NO OTHER WARRANTY OR REPRESENTATION, AND
HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES
THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT
WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHAS-
ER'S INTENDED USE.
Purchaser's Remedy
Horizon's sole obligation and purchaser's sole and exclusive
remedy shall be that Horizon will, at its option, either (i) service,
or (ii) replace, any Product determined by Horizon to be defec-
tive. Horizon reserves the right to inspect any and all Product(s)
involved in a warranty claim. Service or replacement decisions
are at the sole discretion of Horizon. Proof of purchase is
required for all warranty claims. SERVICE OR REPLACEMENT
AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER'S
SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY
OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Further, in no event shall the liability of Horizon exceed the
individual price of the Product on which liability is asserted.
As Horizon has no control over use, setup, final assembly,
modification or misuse, no liability shall be assumed nor
EN
CONTROL
THE AIR