Related Manuals for Atlas Copco Secoroc G10
Summary of Contents for Atlas Copco Secoroc G10
- Page 1 Secoroc Rock Drilling Tools Secoroc Pneumatic Tools Secoroc G10/G10L Pneumatic Pick Hammer Operator's instructions / Spare parts list...
- Page 2 Foreword Thank you for selecting the Secoroc pick hammer G10/G10L. These instructions were developed to help you get the best performance and productivity from the use of your new pick hammer. Please refer to them also for the correct maintenance of the pick hammer.
-
Page 3: Table Of Contents
Table of Contents Scope of application ........... 4 Specification . -
Page 4: Scope Of Application
Scope of application The Secoroc pneumatic pick hammer G10/G10L is a machine with D-handle, designed for light demolition and plant work. The machine can be used both horizontally and vertically. No other use is permitted. Specification Pneumatic pick hammer G10L Weight 10.6 10.6... -
Page 5: Safety Instructions
Safety instructions To reduce the risk of serious injury or death to yourself or others, carefully read through this instruction booklet before putting the pick hammer to use. Always follow the instructions given in this manual. Always wear a safety helmet, impact resistant eye protection with side protection and ear protectors during breaking. -
Page 6: Operation
Operation Using the pick hammer for the first time When the pick hammer arrives from the factory, the inside of the tool is coated with heavy oil to prevent corrosion. After unpacking and installing the machine, pour a small amount of thin lubrication oil into the air connection and operate the machine on partial throttle to clean the interior. -
Page 7: Fitting The Insertion Tool
4. Air pressure and hose dimensions Air pressure Ensure that the compressor can deliver the required air pressure of 5 bar at the machine. Measure the pressure close to the inlet nipple when operating the pick hammer. High pressure (>5 bar) causes rough operation and damage. Low pressure (<4 bar) results in a slow breaking speed. -
Page 8: Fitting The Insertion Tool
Fitting the insertion tool 1. Unscrew the tool retainer from the cylinder. 2. Insert the insertion tool into the chuck. 3. Screw the tool retainer onto the cylinder. Tighten it using a hammer. Start and Stop Starting the pick hammer The pick hammer starts when the inserted tool is pushed into the cylinder. -
Page 9: Operating
Operating Avoid working in extremely hard materials e.g. granite and reinforcing iron (reinforcement bar) which would cause substantial vibrations and excessive wear on the pick hammer. Check regularly that the machine is well lubricated. The chuck and insertion tool shank must always be covered by a film of oil. Maintenance Regular maintenance is a prerequisite for machine safety. -
Page 10: Storage
Storage Always oil the pick hammer before putting it into storage. Store the pick hammer in a clean and dry place. In the case of long-term storage, pour a quantity of oil directly into the pick hammer air intake and then turn on the air briefly. This will protect the machine from corrosion. -
Page 12: Spare Parts List And Exploded Drawing
Spare parts list and exploded drawing... - Page 13 Description Quantity Product no. Product code G10L Handle 3312 3104 86 966P-1-3312310486 Handle spring 3312 3104 89 966P-1-3312310489 Stop valve sleeve 3312 3104 90 966P-1-3312310490 Stop valve 3312 3104 92 966P-1-3312310492 Stop valve spring 3312 3104 93 966P-1-3312310493 Valve chest pad 3312 3104 94 966P-1-3312310494 Valve...
- Page 14 NOTES...
- Page 15 NOTES...
- Page 16 Atlas Copco Secoroc AB Box 521, SE-737 25 Fagersta, Sweden Phone: +46 223 461 00 E-mail: secoroc@se.atlascopco.com www.atlascopco.com...
Need help?
Do you have a question about the Secoroc G10 and is the answer not in the manual?
Questions and answers