Download Table of Contents Print this page

Honeywell Voyager XP 1470g Series Quick Start Manual

Corded area-imaging scanner
Hide thumbs Also See for Voyager XP 1470g Series:


Voyager™ XP 1470g Series
Corded Area-Imaging Scanner
Quick Start Guide
VG1470-EN-QS-01 Rev A


Table of Contents

Summary of Contents for Honeywell Voyager XP 1470g Series

  • Page 1 Voyager™ XP 1470g Series Corded Area-Imaging Scanner Quick Start Guide VG1470-EN-QS-01 Rev A 5/19...
  • Page 2: Getting Started

    Agency Model: 1470g Note: Refer to your User Guide for information about cleaning your device. Getting Started Turn off computer’s power before connecting the scanner, then power up the computer once the scanner is fully connected. Power Supply Assembly (if included)
  • Page 3 Connecting the Scanner...
  • Page 4 Keyboard Wedge: RS232 Serial Port:...
  • Page 5 RS485:...
  • Page 6: Reading Techniques

    Reading Techniques The view finder projects an aiming dot that should be centered over the bar code, but it can be positioned in any direction for a good read. Hold the scanner over the bar code, press the button, and center the aiming dot on the bar code.
  • Page 7 RS485 Interface The RS485 interface defaults to port 5B. If you have an IBM POS terminal using port 9B, scan the appropriate code below to pro- gram the terminal, then power cycle the cash register. IBM Port 9B HHBCR-1 Interface IBM Port 9B HHBCR-2 Interface Note: For additional RS485 interface selections, see the User...
  • Page 8: Keyboard Country

    Keyboard Country Scan the appropriate country code that follows to program the keyboard layout for your country or language. By default, national character replacements are used for the following characters: # $ @ [ ] \ | ^ ‘ { } ~ Refer to the ISO 646 Character Replacements chart in your User Guide to view the character replacements for each country.
  • Page 9 Italy Norway Spain Switzerland Note: For a complete list of country codes, see the User Guide for your product. Trigger The following bar codes will allow you to use the scanner in Manual Trigger - Normal Mode (need to press the button to read) or Presentation mode (the scanner is activated when it “sees”...
  • Page 10: Add Code Id Prefix To All Symbologies

    Suffix If you want a carriage return after the bar code, scan the Add CR Suffix bar code. To add a tab after the bar code, scan the Add Tab Suffix bar code. Otherwise, scan the Remove Suffix bar code to remove the suffixes. Add CR Suffix Add Tab Suffix Remove Suffix...
  • Page 11: Function Code Transmit

    Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in your User Guide. When the scanner is in key- board wedge mode, the scan code is converted to a key code before it is transmitted.
  • Page 12: Data Format Editor Instructions

    Data Format Editor Instructions The following are abbreviated instructions for entering a data format. For complete instructions refer to your User Guide. Step 1. Scan the Enter Data Format symbol. Step 2. Primary/Alternate Format: scan 0 for Primary Format Step 3. Terminal Type: scan 099 for any terminal type Step 4.
  • Page 13: Programming Chart

    Programming Chart...
  • Page 14: Ezconfig For Scanning

    Save EZConfig for Scanning To access additional features for the scanner, use EZConfig for Scanning, an online configuration software tool, available from our website.
  • Page 15: Limited Warranty

    Patents For patent information, see Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.

This manual is also suitable for:

Voyager xp 1470g2dVoyager xp 1470g1d

Table of Contents