Smanos WK7000 Manual

Wireless keypad
Hide thumbs Also See for WK7000:

Advertisement

EN
Please read this manual carefully before using.
Please keep it properly for further reference.

Table of Contents

Introduction ...................................................................................................................1-4
Foreword ............................................................................................................................ 1
Package List .......................................................................................................................2
Product Overview ........................................................................................................3-4
Preparation before Use ..............................................................................................4-8
Power on ............................................................................................................................ 4
Connect Keypad to Control Panel ...............................................................................5
Connect RFID Tag to Keypad ........................................................................................6
Connect Electronic Door Lock ......................................................................................8
Installation .......................................................................................................................... 8
Settings ........................................................................................................................ 9-20
Enter Setup State .............................................................................................................9
Exit Delay .........................................................................................................................10
Setting for SOS Key .......................................................................................................11
Keyboard Tone ................................................................................................................13
RFID Reader Setting ......................................................................................................14
Direct Disarm by RFID Tag ...........................................................................................16
Change User Code ........................................................................................................18
Change Admin Code ....................................................................................................19
Reset .................................................................................................................................20
Usage ......................................................................................................................... 20-24
Arm....................................................................................................................................21
Disarm ..............................................................................................................................21
Stay Mode .......................................................................................................................23
Emergency Call ...............................................................................................................23
Mute Mode .....................................................................................................................24
Notices and Maintenance ..................................................................................... 25-26
Usage Notices .................................................................................................................25
Maintenance ...................................................................................................................26
FAQ ............................................................................................................................. 27-28
Instructions of Wired Cables Interface ......................................................................29
Specifications ..................................................................................................................29
EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WK7000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Smanos WK7000

  • Page 1: Table Of Contents

    Table of Contents Introduction ........................1-4 Foreword ..........................1 Package List ........................2 Product Overview ......................3-4 Preparation before Use ....................4-8 Power on ..........................4 Connect Keypad to Control Panel ................5 Connect RFID Tag to Keypad ..................6 Connect Electronic Door Lock ..................8 Installation .......................... 8 Settings ........................
  • Page 2: Foreword

    Foreword Package List Thank you for purchasing this wireless keypad. It is recommended to install outside the entry door and users can achieve operations such as arm, disarm, stay mode after inputting passcode. Moreover, the keypad can connect with an electric door lock to work as an access control system for homes and offices.
  • Page 3: Product Overview

    Product Overview LED indicator Positive and negative terminals for battery ① RFID reader ① Battery compartment LED indicator LED indicator Positive and negative Positive and negative terminals for battery ① terminals for battery ① Tamper switch RFID reader ① RFID reader Disarm ①...
  • Page 4: Connect Keypad To Control Panel

    The default user code is 1234. ① The default admin code is 123456. ② Connect Keypad with RFID Tag Note: Open the rear cover of keypad will trigger tamper switch, please dismiss 1. Input [admin code] to wake up keypad. the alarm by following the disarm instruction on page 21-22.
  • Page 5: Connect Electronic Door Lock

    2. Press, one beep is heard a nd the LED indicator is on. Keypad Connect Electric Door Lock enters learning state. To know connection steps, please refer to the instruction manual of electric door lock. Installation Fix the keypad on the wall before use. Loose the screw, open the case ①...
  • Page 6: Settings

    Settings Exit Delay The keypad should enter setup state before all settings. The Exit Delay allows time to leave after arming the system. After the delay time, if you are still at home, you may trigger an alarm. This setting does not apply to Stay Mode. Enter Setup State If the delay time of both control panel and keypad are set Input...
  • Page 7: Setting For Sos Key

    *3 * 1* Setting for SOS Key Input Code for SOS *2* Verzögerungszeit * Enter setup state, input: You can choose to input code before pressing [SOS] key or not. This *3 * 1* function is to prevent false operation or trick. *2* Verzögerungszeit * Not Input Code for SOS Enter setup state, input:...
  • Page 8: Keyboard Tone

    *3 * 1* Keyboard Tone *4 * 1* Keyboard tone can be turned on or off. If it is off, the setup confirmation tone will be turned off too. Turn off Keyboard Tone Enter setup state, input: When one beep is heard and the LED indicator keeps on for 10 *4 * 0* seconds, the setup is successful.
  • Page 9: Direct Disarm By Rfid Tag

    Enable RFID Reader Enter setup state, input:: Enter setup state, input: *5 * 2* *5 * 1* When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is successful. When one beep is heard and the LED indicator keeps on for 10 Note: Default setting: 1, turn on disarm by RFID tag and the siren will hoot seconds, the setup is successful.
  • Page 10: Change User Code

    Change User Code Disable Direct Disarm by RFID Tag Enter setup state, input: *9*neuer Admin-Code* Using user code can wake up keypad, open electronic door lock, or *7 * 0* send Arm, Disarm, Stay Mode commands to the control panel. To avoid passcode reveal, please change user code when first time use.
  • Page 11: Change Admin Code

    *9*neuer Admin-Code* Change Admin Code Reset *7 * 0* Using admin code can wake up keypad, send Arm, Disarm, Stay After reset, the user code, admin code, and other settings will Mode commands to the control panel, and also change any settings restore to default except that the connected RFID tags can still of the keypad.
  • Page 12: Arm

    When the alarm panel receives the signal, the siren will beep twice and the Disarm indicator will light on, the alarm system enters Input user code or admin code, and press [Arm] key, the LED disarmed state. In this state, the sensors being triggered will not indicator flashes once and the keypad beeps once and sends [Arm] cause an alarm.
  • Page 13: Stay Mode

    Stay Mode If inputting code for SOS is set, user needs input user code or admin code before holding the [SOS] key for 3 seconds to send an Input user code or admin code, and press [Stay Mode] key, the LED alarm.
  • Page 14: Notices And Maintenance

    Notices and Maintenance Install the keypad away from objects such as heater, air conditioner, microwave oven etc. that produces heat or electric-magnetic. In order to avoid any harm to the users or others during usage and Forbiddance of decomposition prolong the usage life, please abide by the following notices. Take the keypad for disposal of recycling according to the local regulation.
  • Page 15: Faq

    The RFID tags are Please connect the RFID tag to not learned to control panel by following the keypad manual instruction Cannot disarm by Disarm by RFID tag Enter setup state and activate Problem Cause Solution RFID Tags function is the function of disarm by RFID Low battery Please change the battery...
  • Page 16: Instructions Of Wired Cables Interface

    Negative of power OPEN (GREEN WIRE) Signal input for exit switch Specifications Product Name Keypad Model No. WK7000 Power Supply 3 pcs of AAA batteries or DC 12V Static Current < 20 uA (powered by batteries) Transmitting Current < 24 mA...

Table of Contents