Download
Share
Print this page
  1. Manuals
  2. Brands
  3. KERAFLO Manuals
  4. Control Unit
  5. AYLESBURY KAX
  6. Installation manual

KERAFLO AYLESBURY KAX Installation Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
aylesbury
kaX valve
installation guide
For valve sizes (dn):
2"(50)HF
2½"(65)sF
3"(80)rb
iMPortant
Please keeP for future reference.
Please reaD tHese InstructIons
carefullY anD refer to anY DIaGraMs
Before InstallatIon.
These instructions contain important
information which will help you install
your keraFlo delayed action float
valve correctly and ensure safe use
and maintenance.
For further assistance please ring our
Customer Helpline: 0118 921 9920
tel 0118 921 9920
fax 0118 921 9921
info@keraflo.co.uk
www.keraflo.co.uk
P/KAXTFINSTALL A-02

Advertisement

loading

Related Manuals for KERAFLO AYLESBURY KAX

Summary of Contents for KERAFLO AYLESBURY KAX

  • Page 1 DIaGraMs Before InstallatIon. These instructions contain important information which will help you install your keraFlo delayed action float valve correctly and ensure safe use and maintenance. For further assistance please ring our Customer Helpline: 0118 921 9920...
  • Page 2 details.

  • Page 3: Pre-Installation

    PiPeWork to Position tHe valve asseMbly in tHe centre oF tHe tank cHaMber. sloPing tank The wall to which the Aylesbury KAX Valve is to be attached must be vertical. If the Wall: wall around the fixing hole is sloped, tapered washers must be used. These should be available from the tank supplier.

  • Page 4: Installation Instructions

    Warning! instructions tHe BuIlt-In sPIrIt level Must Be useD to alIGn tHIs valve. faIlure to follow tHe ProceDure lIsteD Below wIll Prevent tHe valve oPeratInG correctlY anD wIll The valve is supplied with the float arm and InvalIDate tHe warrantY.
  • Page 5 Level the two valves on the T-outlet use a sPirit level to ensure by placing a spirit level across the t-outlet is Horizontal T-outlet, parallel to the tank wall on which it is mounted and twisting the whole assembly to bring the valves level.
  • Page 6 4 Align each valve, tighten the locknuts, and re-check the alignment. eacH bubble Must be Precisely betWeen tHe black lines on tHe sPirit level. Check that the clearance between sPirit the tank wall and the floats is at least...
  • Page 7 6 Using the 4mm Allen key supplied, fit the discharge assembly referring to Hold WitH Diagram 6 for the direction. WrencH Here, only. Connect the supply pipe after an isolating valve and hand tighten the connection backnut. To prevent the...
  • Page 8 Have been installed and tested, coMPlete and aPPly tHe tank label to tHe tank and send a PHotograPH oF tHe label in Place to Warranty@keraFlo.co.uk in order to receive a Full Five years’ eXtended Warranty For tHe valve. see Warranty sHeets For Full details.
  • Page 9 (dn): 2”(50)HF discHarge asseMbly adJust alignMent 2½”(65)sF Here 3”(80)rb valve valve body body sPirit level WasHer sPigot double r cliP Float arM busH insert WeigHt slide Float into Float adJusting desired closing catcH (Pull to level (tWl)
  • Page 10 (dn): HigHest Water level setting 2”(50)HF 2½”(65)sF 3”(80)rb Øe b MaX Warning tHe float arM Must Be fItteD aBsolutelY closed vertIcallY (In tHe oPen PosItIon) as InDIcateD Position closing level BY tHe sPIrIt level (see Below).
  • Page 11 0118 921 9920 fax 0118 921 9921 info@keraflo.co.uk www.keraflo.co.uk...
  • Page 12 0118 921 9920 fax 0118 921 9921 info@keraflo.co.uk www.keraflo.co.uk...