H3C S9500 Series Operation Manual
H3C S9500 Series Operation Manual

H3C S9500 Series Operation Manual

Ethernet port, routing switches
Hide thumbs Also See for S9500 Series:

Advertisement

Operation Manual - Ethernet Port
H3C S9500 Series Routing Switches
Chapter 1 Ethernet Port Configuration ....................................................................................... 1-1
1.1 Ethernet Port Overview...................................................................................................... 1-1
1.2 Ethernet Port Configuration ............................................................................................... 1-1
1.2.1 Entering Ethernet Port View.................................................................................... 1-2
1.2.2 Enabling/Disabling an Ethernet Port ....................................................................... 1-2
1.2.3 Setting Ethernet Port Description............................................................................ 1-2
1.2.4 Setting the Duplex Attribute of an Ethernet Port ..................................................... 1-2
1.2.5 Setting Speed on the Ethernet Port ........................................................................ 1-3
1.2.6 Setting the Cable Type for the Ethernet Port .......................................................... 1-4
1.2.7 Enabling/Disabling Flow Control for the Ethernet Port............................................ 1-5
1.2.8 Setting the Interval for Performing Statistics on the Port ........................................ 1-5
1.2.9 Permitting/Denying Jumbo Frames......................................................................... 1-6
1.2.11 Setting the Network Mode of an Ethernet Port ..................................................... 1-7
1.2.12 Setting the Link Type for the Ethernet Port........................................................... 1-8
1.2.13 Adding the Ethernet Port to Specified VLANs....................................................... 1-9
1.2.14 Setting the Default VLAN ID for the Ethernet Port ................................................ 1-9
1.2.15 Setting the VLAN VPN Feature on a Port ........................................................... 1-10
1.2.17 Copying Port Configurations to Other Ports........................................................ 1-11
1.2.18 Setting the Link-State Hold Time ........................................................................ 1-13
1.2.19 Setting the Ethernet Port in Loopback Mode ...................................................... 1-14
1.3 Displaying and Maintaining Ethernet Port Configuration ................................................. 1-14
1.4 Ethernet Port Configuration Example .............................................................................. 1-15
1.5 Troubleshooting Ethernet Ports ....................................................................................... 1-16

Table of Contents

i
Table of Contents

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S9500 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for H3C S9500 Series

  • Page 1: Table Of Contents

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Table of Contents Table of Contents Chapter 1 Ethernet Port Configuration ..................1-1 1.1 Ethernet Port Overview...................... 1-1 1.2 Ethernet Port Configuration ....................1-1 1.2.1 Entering Ethernet Port View..................1-2 1.2.2 Enabling/Disabling an Ethernet Port ...............
  • Page 2: Chapter 1 Ethernet Port Configuration

    Troubleshooting Ethernet Ports 1.1 Ethernet Port Overview The S9500 series can provide conventional Ethernet ports, fast Ethernet ports, 1,000 Mbps Ethernet ports and 10 Gbps Ethernet ports. The configurations of these Ethernet ports are basically the same, which will be described in the following sections.
  • Page 3: Entering Ethernet Port View

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration 1.2.1 Entering Ethernet Port View Before configuring an Ethernet port, enter Ethernet port view first. Perform the following configuration in system view. To do …...
  • Page 4: Setting Speed On The Ethernet Port

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration To do … Use the command … Set duplex attribute for the Ethernet port duplex { auto | full | half } Restore the default duplex attribute of the...
  • Page 5: Setting The Cable Type For The Ethernet Port

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration To do … Use the command … Set Ethernet port speed speed { 10 | 100 | 1000 | 10000 | auto } Restore the default speed on the...
  • Page 6: Enabling/Disabling Flow Control For The Ethernet Port

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration To do … Use the command … Set the type of the cable connected to the mdi { across | auto | normal } Ethernet port...
  • Page 7: Permitting/Denying Jumbo Frames

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration To do … Use the command … Remarks Set the interval for Required performing statistics on flow-interval interval 300 seconds by default the port 1.2.9 Permitting/Denying Jumbo Frames During large throughput data switching, like in file transmission, a card may encounter jumbo frames larger than the standard Ethernet frame length.
  • Page 8: Setting The Network Mode Of An Ethernet Port

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration To do … Use the command … Configure broadcast suppression on the broadcast-suppression { ratio | Ethernet port bandwidth bandwidth } Restore the default setting of broadcast...
  • Page 9: Setting The Link Type For The Ethernet Port

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration To do … Use the command … Set the network mode of the Ethernet port port-mode { wan | lan } Restore the default network mode undo port-mode By default, Ethernet ports work in LAN mode.
  • Page 10: Adding The Ethernet Port To Specified Vlans

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration 1.2.13 Adding the Ethernet Port to Specified VLANs The following commands are used for adding an Ethernet port to a specified VLAN. The access port can only be added to one VLAN, while the hybrid and trunk ports can be added to multiple VLANs.
  • Page 11: Setting The Vlan Vpn Feature On A Port

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration To do … Use the command … Set the default VLAN ID for the hybrid port port hybrid pvid vlan vlan-id Set the default VLAN ID for the trunk port...
  • Page 12: Enabling/Disabling The Vlan Filtering Function On An Ethernet Port

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration To do … Use the command … Enable the port VLAN VPN feature vlan-vpn enable Disable the port VLAN VPN feature undo vlan-vpn Note that if GVRP, STP, or 802.1x has been enabled on the port, you will be unable to enable the VLAN VPN feature.
  • Page 13 Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration Table 1-1 Configurations that can be copied Attribute Detailed Setting Enable/disable STP Port priority Path cost Link attributes(point-to-point or not) Port mCheck STP settings Max transmission speed...
  • Page 14: Setting The Link-State Hold Time

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration Note: Using the copy configuration command will clear protocol VLAN attributes of the destination port, but it will not copy the protocol VLAN attributes of the source port to the destination port.
  • Page 15: Setting The Ethernet Port In Loopback Mode

    Remove loopback configuration on the port undo loopback Note: At present, the Ethernet ports of the S9500 series switches do not support the external loopback mode. By default, the Ethernet port is not in loopback mode. 1.3 Displaying and Maintaining Ethernet Port Configuration To do …...
  • Page 16: Ethernet Port Configuration Example

    Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration To do … Use the command … Remarks Display Jumbo frame display jumboframe Available in any view configuration on all cards configuration Display the current alarm...
  • Page 17: Troubleshooting Ethernet Ports

    # Configure GigabitEthernet 2/1/1 as a trunk port permitting packets of VLAN 2, VLAN 6 through VLAN 50, and VLAN 100. [H3C-GigabitEthernet2/1/1] port link-type trunk [H3C-GigabitEthernet2/1/1] port trunk permit vlan 2 6 to 50 100 [H3C-GigabitEthernet2/1/1] quit # Create VLAN 100.
  • Page 18 Operation Manual – Ethernet Port H3C S9500 Series Routing Switches Chapter 1 Ethernet Port Configuration Solution: Check that The cable connection is correct and the optical fibers are correctly connected. The port has not been administratively shut down. The correct optical module is used.

Table of Contents