1. Manuals
  2. Brands
  3. Abus Manuals
  4. Switch
  5. ITAC10120
  6. User manual

Abus ITAC10120 User Manual

Web management
Hide thumbs Also See for ITAC10120:
Table of Contents

Advertisement

Quick Links

Download this manual
User manual Web Management
Originalbedienungsanleitung in deutscher Sprache. Für künftige Verwendung aufbewahren.
This user manual contains important information for installation and operation.
This should be also noted when this product is passed on to a third party.
Therefore look after these operating instructions for future reference!
Version 05/2019
ITAC10120
ITAC10130

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ITAC10120 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Abus ITAC10120

Summary of Contents for Abus ITAC10120

  • Page 1 ITAC10120 ITAC10130 User manual Web Management Originalbedienungsanleitung in deutscher Sprache. Für künftige Verwendung aufbewahren. This user manual contains important information for installation and operation. This should be also noted when this product is passed on to a third party. Therefore look after these operating instructions for future reference!

  • Page 2: Table Of Contents

    Inhalt Access to Web Management ....................5 Access to Web Management ..................5 Access to Web Management via CLS Port ..............5 Reset ........................... 5 Web Management ......................7 System Status ....................... 7 Port setting ........................8 3.2.1 Port speed limit ..................... 9 VLAN settings ......................

  • Page 3: Access To Web Management

    1 Access to Web Management 1.1 Access to Web Management To connect to the web management interface, connect a network cable to any of 1- 16/1-24 RJ45 port and enter the following data into browser. The default factory settings are: IP-Address: 192.168.1.200 User:...
  • Page 4 The factory default settings of the device are as following: Options Default Configuration System Username / password admin/admin IP-Address IP-Address：192.168.1.200 Subnet Mask：255.255.255.0 MAC address table 300 Seconds aging time Port Ports Status Enable Ports Speed Rate Auto-negotiation Ports duplex mode Auto-negotiation Flow Control Open...

  • Page 5: Web Management

    3 Web Management 3.1 System Status Description Select your time zone or select “Automatically”. Word Time Select “Adjust Daylight Saving Time” for automatically DST Zone correction. Select “Local Time” or use NTP function. Time Configuration Enter the correct NTP server’s IP address to start the sync. NTP Server System Time The current time of the device, if you did not get the NTP updated...

  • Page 6: Port Setting

    3.2 Port setting On the [Port security / Port Settings] page, you can observe the status and make different settings for ports. Description Port Enable / Enabled by default. Disable Enable or disable a certain port. If a port is disabled, you cannot transmit any data on this port. Port Speed Auto-negotiation mode by default.

  • Page 7: Port Speed Limit

    3.2.1 Port speed limit Users can restrict every port traffic flow. Port restrictions including Unicast packets, Multicast packet and broadcast packets. The accuracy is 1Mbps. The range is: • For downlink ports 1～1000Mbps • For uplink ports 1～ 1000Mbps Description Bandwidth Off by default.

  • Page 8: Vlan Settings

    3.3 VLAN settings The switch supports two VLAN modes: Port-based VLAN mode: Define VLAN members according to device port. After you specify the port to a VLAN, specified VLAN Packets can be forwarded by the port. 802.1Q VLAN mode: Defined by IEEE802.1Q protocol. Process the packets by identifying the packets tags.

  • Page 9: Vlan Forwarding

    3.3.1 VLAN Forwarding On the [VLAN / VLAN forwarding] page, you can observe the current port VLAN forwarding settings. Description VLAN ID Change VLAN ID. VLAN Name Change VLAN name.

  • Page 10: Trunk Management

    3.4 Trunk Management TRUNK means port convergence. After configuration two or more physical ports to become a logical path to increase the bandwidth between switches and network nodes. On the [LACP / TRUNK] page, you can observe the current port link convergence settings.

  • Page 11: Rstp

    3.5 RSTP STP (Spanning Tree Protocol) is established in accordance with IEEE 802.1D standard. It is developed for the elimination of the data link layer loops in the LAN protocol. Devices running this protocol exchange packets with each other to find loops in the network and choose to block some certain ports.
  • Page 12 Port status Forwarding: Forwarding user traffic, only the root port or designated port have this condition. Learning: The switch builds the MAC address table according to user traffic received (but not forwarding traffic). Listening: The completion of the root bridge, select the root port and designated ports.

  • Page 13: Rstp

    3.5.2 RSTP RSTP (Rapid Spanning Tree Protocol) is an optimized version of STP. It is" fast" because the delay is shortened under certain conditions when a port is selected as the root port and designated port to enter to the forwarding state, thus the time to reaching topology stability is greatly reduced.

  • Page 14: Port Security

    3.6 Port Security Statics Address Latch Statics MAC address is to limit computer operation. The computer with binding computer MAC and ports cannot communicate with other ports, while other computer can do that. On the [Port security/Stastic address lock] page displays switch information of statics address latch.

  • Page 15: 802.1X Certificates

    3.6.1 802.1X certificates IEEE 802.1X certification system adopted the "controllable port" and "uncontrolled ports" logic functions. It can realize the separation of business and certification. After passing certification, the business flow and the certification flow separation, it has no special requirement for the following subsequent packets. Business can be flexible, especially in develop broadband multicast business, it has a lot of advantages.
  • Page 16 Description 802.1X config The is default off. Turn 802.1X certification On/Off. Regularly The certification cycle time, used to enhance the security of update the authentication. certification Radius Server If you select internal Radius server，applicants will only be used inside the Radius database users and password. If you select external Radius server, you will need to fill in the authentication server IP address and Ports.

  • Page 17: Web Management

    4 Web Management 4.1 SNMP Settings SNMP is used to ensure the management information transferred between any two points, so that network administrators can easily retrieve information on any node on the network to modify information, fault search, troubleshooting, capacity planning and report generation.

  • Page 18: Email Alarm

    4.2 Email Alarm The device if it is running an event supervision, the supervision sends an alert message to defined Email recipients when something wrong about defining time and some abnormal event occurs. Supervision also periodically send all log messages to predefined recipients.

  • Page 19: Port Mirror

    4.3 Port Mirror Port mirroring refers to copying the monitor port data to a designated monitoring port for data analysis and monitoring. The Ethernet Switch supports multiple mirroring to one mirroring, which Copy packets from multiple ports to a monitor port. User can also specify the direction of monitored packets, such as only monitor designated ports message.

  • Page 20: Igmp Snooping

    4.4 IGMP Snooping Switch IGMP membership report message to the router IGMP membership through intercepting mainframe. Form Corresponding relationship between group members and switch interfaces. Switch transfer multicast packets be received to member group ports according to Correspondence. The [Network Management/ IGMP Snooping] Page, Modify and setting [ IGMP Snooping] function.

  • Page 21: Network Statistics

    5 Network Statistics On the [Network statistics / Flow statistics] page, you can view the number of data packets and bytes transferred for each port. Description Receive Frame The received address is the number of packets in the unicast Singlecast address.

  • Page 22: Mac Address

    5.1 MAC Address MAC (Media Access Control) address is the hardware identification of network equipment. Switches could transfer message according to MAC address. The MAC address is unique ,which ensures the correct message. Every switch maintains a MAC address table, in which, the MAC address corresponds to switch ports. The switch could decide to filter this data frame or transfer data frame to corresponding port according to MAC address table when the switch receives data frame.

  • Page 23: System Management

    6 System Management 6.1 IP Address On this page, you can check the IP address for this device. Attention: Please fill in correct DNS address when using it for NTP and Email. User Management On this page, you can modify or add one user with password. Description User Index User index indicates the group of users.

  • Page 24: Log Information

    6.2 Log Information The log function allows users to access information of the system operation. When this function is enabled, corresponding events are recorded to the log: • System restart • Port Link Down/UP • Power supply status • Login information •...

  • Page 25: File Management

    6.3 File Management On the [System management/ File management] page you can check configure document, software upgrade, restore factory setting and reboot system. Description Configuration Backup switch configuration (File format *.cfg) File Restore switch configuration (File format *.cfg) Software Select file to perform firmware update. Update Restore Set switch to default settings, except for IP address, user name...

  • Page 26: Poe Management

    7 PoE Management On PoE management page, you can turn on/off PoE function, set input power, maximum overload, reservation power etc. Attention: Please do not modify the input power, if the setting value is more than the actual power of the built-in power, there will be a risk of overload burning. If the setting value is less than the actual power for the built-in power supply, it cannot be fully allocated out.
  • Page 27 Provided Total power for system setting. It stems from the set menu “input power”. There are three levels for port power: “low”, “middle”, “high”. Priority Supply priority: when the system is overloaded, the power supply of the port with low priority will be turned off firstly. Power limit Set the output power limit for single port.

  • Page 28: Qos Management

    8 QoS Management On the [QoS management/QoS Settings] page you can modify the QoS function. Description QoS Setting The default is Off. Turn QoS function on / off. 802. 1P QoS Set traffic priority. Setting The highest priority is 7，then to 6、5、4、3、2、1、0 802.
  • Page 29 Impressum Diese Bedienungsanleitung ist eine Publikation der ABUS Security-Center GmbH & Co. KG, Linker Kreuthweg 5, 86444 Affing. Alle Rechte einschließlich Übersetzung vorbehalten. Reproduktionen jeder Art, z.B. Fotokopie, Mikroverfilmung, oder die Erfassung in elektronischen Datenverarbeitungsanlagen, bedürfen der schriftlichen Genehmigung des Herausgebers.

This manual is also suitable for:

Itac10130

Table of Contents