Advertisement
Device operating modes
El equipo se debe confi gurar para trabajar en uno de los cua-
tro modos de funcionamiento posibles. La confi guración del
modo de funcionamiento se realiza a través del parámetro P5
del menú de confi guración.
Operating mode nº 1
Through this operating mode, device is set as follows:
• Room changes into Occupied/Unoccupied state throug-
hout Key card contact input (IN1).
- Window input (IN2) controls climate state.
- Lighting input (IN3) controls Lighting output (OUT2) state.
- Temperature sensor input (IN4) controls Zone 2 valve ac-
tuator output (OUT4).
- Courtesy lighting output (OUT1) and Lighting output
(OUT2) are depending on occupancy room state
Operating mode nº 2
Through this operating mode, device is set as follows:
- Room changes into Occupied/Unoccupied state throug-
hout Key card contact input (IN1).
- Window input (IN2) controls climate state.
- Raising blinds up input (IN3) controls Raising blinds up
output (OUT3) state.
- Lowering blinds down input (IN4) controls Lowering blinds
Pushbuttons operation
On/Off
Climate switch on and switch off when room is in occupied
state ( 1, 2 and 3 operating modes). When room is unoccupied
climate can't be turned on until room changes to occupied
state.
Fan-Coil Speed
Pushbutton for automatic/manual mode and fan coil speeds.
When the device starts, selector is in automatic mode (AUTO). In
this mode, the device automatically manages fan coil speeds for
each moment. By pressing the pushbutton, the device changes
into manual mode (MAN), disappearing the AUTO icon on the
display and showing the speed I icon. Each press changes fan
coil speed following the sequence: I-II-III-AUTO. After speed III,
AUTO mode is selected again.
Front panel LED description.
The device has a front panel LED which can light in diff erent
colours depending on the device state.
• Green: When climate is switched off , LED will light in this
colour.
• Switched off : When climate is switched on, LED will keep
Product installation
This device should not be installed on shelves, behind curtains,
above or near heat sources, or exposed to direct sunlight.
For fast and accurate ambient temperature measurement,
the controller should be installed such that air may circulate
vertically. Installation height should be approximately 1.5 m
from the fl oor.
Caution:
- Prior to installing or removing the device, ensure that there
is no mains voltage present in the wiring to be connected
or near the unit.
- Do not cut or roll up the wires to be connected to the
device.
- Do not work on the wiring with wet hands.
- Do not open or drill through the device.
- Keep the device and the supply wires away from moisture
and dust.
- Use a damp cloth to clean the device.
INS1114507000-0
down output (OUT4) state.
- Courtesy lighting output (OUT1) and Lighting output
(OUT2) are depending on occupancy room state.
Operating mode nº 3
Through this operating mode, device is set as follows:
- Room changes into Occupied/Unoccupied state throug-
hout Motion sensor input (IN1) and Door contact input
(IN3).
- Window input (IN2) controls climate state.
- Temperature sensor input (IN4) controls Zone 2 valve ac-
tuator output (OUT4).
- Courtesy lighting output (OUT1) and Lighting output
(OUT2) are depending on occupancy room state.
Operating mode nº 4
Through this operating mode, device is set as follows:
- Lighting input (IN1) controls Lighting output (OUT2) state.
- Window input (IN2) controls climate state.
- Raising blinds up input (IN3) controls Raising blinds up
output (OUT3) state.
- Lowering blinds down input (IN4) controls Lowering blinds
down output (OUT4) state.
Set-point temperature
Set-point temperature value increments or decrements until
maximum and minimum limits confi gured on the device.
5 seconds after the last press, the device returns to resting
state displaying ambient temperature or set-point temperature
depending on how it has been confi gured.
After 10 seconds backlight will switch off .
Heat/Cool
It changes operating device mode between HEAT, COOL, AUTO.
In COOL mode the device is confi gured to provide cool air
and shows
icon on the display. In HEAT mode the device
is confi gured to provide warm air and shows
display. In AUTO mode, indoor unit determines if it is necessary
to provide cool or warm air and shows AUTO icon on the display
apart from
or
icon depending on system confi guration.
This mode only could be selected if the device is confi gured as
3P mode throughout P3 parameter.
switch off .
• Red: When device is connected to power supply, LED will
remain switch on in red colour while it is initializing.
• Blinking red: it indicates there is an indoor unit failure or a
communication failure.
Installation steps:
1- Install the fl ush mount back box on the wall
2- Connect all wires to the appropriate device terminals
ensuring that there are no voltage in any wire
3- Seal the internal fl exible cable conduit to avoid air fl owing
into the device.
4- Insert and screw the device in the box
5- Fit the frame onto the device
6- Remove the front panel anti-scratch protective foil
4
icon on the
© 2014 e-Controls®
Advertisement
