Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Audiolab 6000CDT
Summary of Contents for Audiolab 6000CDT
- Page 1 REPEAT 6000CDT User Instructions...
-
Page 2: Important Safety Information
MAINS socket outlet with a protective earthing connection. CAUTION: These servicing instructions are for use by Heed all warnings. Mains Supply: The mains operating voltage of Audiolab qualified service personnel only. To reduce the risk of Follow all instructions. -
Page 3: Getting Started
2: Getting Started Welcome to Audiolab 6000 Series. Note: The 6000CDT should be used with the DIGl or OPT outputs connected directly to a preamplifier with inbuilt DAC. 6000CDT is a high performance CD transport that is the perfect partner for other Placement Audiolab components such as 6000A. -
Page 4: Controls And Connectors
3: Controls and Connectors REPEAT Page 3... -
Page 5: Remote Handset
4: Remote Handset NOTE : the handset buttons shown crossed out are for use with other Audiolab units likeAudiolab 6000A and are not operational when used with the 6000A Fitting Batteries 1 STANDBY Press to bring the unit in/out of Standby... - Page 6 Make sure the ON/OFF switch on the One Coaxial and one Optical SPDIF digital output. Connect a 6000CDT is switched off. Switch the mains supply off at the wall socket, and then, using the cable suitable Digital coaxial (fully screened) interconnect or optical supplied, connect the socket on the back of your 6000CDT to an AC supply outlet.
-
Page 7: Operation
If none is entered, The 6000CDT will enter standby mode after being powered on. Press the “Standby” button to player will commence from the entered single-digit track. If the choice is invalid the display bring the 6000CDT out of standby, the power indicator LED becomes brighter and the display reverts to the previous state. -
Page 8: Warranty
Audiolab shall not be liable for any incidental or consequential damages for breach of any express replace (at Audiolab’s option) this product, or any defective part in this product, if it is found to or implied warranty in this product. Except to the extent prohibited by law, this warranty is be defective due to faulty materials, workmanship or function. -
Page 9: Specification
8: Specification Measurement made with 230V power supply Digital Output Voltage Level 600±50mVpp Frequency response ≤0.01dB @ 20-20kHz Output Impedance 75±1 ohm Max Sampling Rate 44.1 KHz Max. Power Consumption Standby Power Consumption <0.5W Power Requirements 240V ~ 50 - 60Hz 230V ~ 50 - 60Hz 115V ~ 50 - 60Hz 100V ~ 50 - 60Hz... - Page 10 Page 9...
- Page 11 Page 10...
- Page 12 Audiolab IAG House, 13 /14 Glebe Road, Huntingdon, Cambridgeshire, PE29 7DL, Tel: +44(0)1480 452561 Fax: +44(0)1480 413403 http://www.audiolab.co.uk CODE: AH14-MNL0004a...
Need help?
Do you have a question about the 6000CDT and is the answer not in the manual?
Questions and answers
I **** having trouble setting the standby time interval on my 6000cdt. When I hold the standby button for three seconds I can only see a numerical code, or 5T 20 mins. I've tried various ways to scroll through to find the never option but failed. The manual doesn't mention much at all.
You can set the standby time interval to "never" on your Audiolab 6000CDT by adjusting the auto standby settings. Your choices are 20 minutes (default), 1 hour, or never (always on). To change this setting, refer to the instructions on page 6 under the heading "6: Operation" in the manual. It should take only a couple of minutes to adjust.
This answer is automatically generated
@Mr. Anderson Thanks, I've managed to do it, more or less by accident. The manual does not describe how to scroll through the options. I tried all sorts but could only get as far as 20 mins. Then 'never' appeared out of nowhere, and I've left it set on that.