Table of Contents
Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
HB0117
ICB3I SERIES
!
!
INTENDED FOR DOMESTIC COOKING ONLY
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGES 12 TO 14.
BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711
BEST; Drummondville, QC, Canada www.BestRangeHoods.ca 866-737-7770
23866 rev. 05
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Best ICB3I Series
Summary of Contents for Best ICB3I Series
- Page 1 INTENDED FOR DOMESTIC COOKING ONLY READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 12 TO 14. BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711 BEST; Drummondville, QC, Canada www.BestRangeHoods.ca 866-737-7770 23866 rev. 05...
- Page 2 9. To reduce the risk of fire and electrical shock, the Best ICB3I b) Always turn hood ON when cooking at high heat or when Series models should only be installed with their own built-in flambeing food (i.e.: Crêpes Suzette, Cherries Jubilee,...
-
Page 3: Table Of Contents
Run 3-wire power supply cable to installation location. 8” OUND We recommend to install the hood at a minimum distance of 30” above cooking surface. A maximum of 36” above cooktop is highly recommended for best capture of cooking impurities. ECORATIVE 8”... -
Page 4: Prepare Installation
2. PREPARE INSTALLATION WARNING When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves. NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. Make sure that the following items are included: –... -
Page 5: Install Mounting Bracket
4. INSTALL MOUNTING BRACKET WARNING When building framework, always follow all applicable construction codes and standards. 10¼" 1. Modify ceiling structure over hood location. Install 2" x 4" cross framing between ⁄ " 10 ⁄ " 10¼" ceiling joists using ceiling mounting bracket dimensions shown at right. The framework must be sized to support the total weight of the hood and should not . -
Page 6: Assemble Angle Brackets
5. ASSEMBLE ANGLE BRACKETS 1. Assemble 4 angle brackets to the ceiling mounting bracket using 16 no.10-32 x 1/2" quadrex screws (4 per angle bracket). HD0421 2. Determine angle brackets length based upon ceiling height and desired height of hood above cooktop. If required, assemble a second set of 4 angle brackets to the upper angle bracket set according to the length needed. -
Page 7: Remove Hybrid Filters
6. REMOVE HYBRID FILTERS Rest the range hood on a table. Protect the table to avoid damaging it. Remove tape on filters. Lift filters by pushing them towards the back of the hood (opposite to control side) and flip, then set filters aside. HO0349 7. -
Page 8: Repare Hood
8. PREPARE HOOD (ALL MODELS) 1. From inside the hood, disconnect the blower. HE0063 LECTRICAL COMPARTMENT RETAINING SCREW 2. Remove the electrical box cover retaining screw. Set cover and screw aside. HE0062 3. Turn the hood over and remove blower box 8 retaining screws (only 4 out of 8 screws illustrated at right). -
Page 9: Install Hood
8. PREPARE HOOD (ALL MODELS) ( ’ CONT 6. Measure the required length of 8" round metal duct from the adapter/damper to the ductwork rough-in in the ceiling. Connect this section of duct to the adapter/damper and seal joint with metal foil duct tape. HJ0067 9. - Page 10 9. INSTALL HOOD ’ CONT 4. Attach the hood to the blower box using the 8 screws previously removed at step 8.3 (only 4 out of 8 screws are illustrated at right). Make sure that the house wiring goes into the electrical compartment. CREW LOCATIONS HD0426 CREW LOCATIONS...
-
Page 11: Connect Wiring
10. CONNECT WIRING WARNING Risk of electric shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power to be switched on accidentally. 1. -
Page 12: Led Lighting
12. LED LIGHTING The lighting of this hood is produced by two LED modules (included). WARNING Do not touch lamps during or soon after operation. Burns may occur. Cannot be replaced by any other type of light bulb or LED module. 13. -
Page 13: Operation
14. OPERATION Always turn your hood on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. CAUTION After a power failure or during the range hood power up, a 5-second booting sequence is executed. Wait for the control backlighting to turn off before use. -
Page 14: Wiring Diagram
14. OPERATION ’ CONT D. L IGHT UTTON ACKLIGHTING OLOR OUBLE UNCTION UTTON i. This button allows three different lighting levels according to your needs. Press once for full intensity, twice for intensity level 2, and once more for nightlight. To turn off the lights, press once more. If desired, when the lights are on, press and maintain the light button for 1 second;... -
Page 15: Service Parts
16. SERVICE PARTS HL0449 ART NO ESCRIPTION SV09956XX* F RONT LASS ANEL SV22427 LECTRONIC ONTROL SV21221 OWER SV20816 FOR REMOTE CONTROL SV09022 RANSFORMER SV08582 NTERNAL LOWER 62248 LED D RIVER AND ONNECTION ARNESS 62612 MODULE SV62053 15.875” 14” x 0.5” (1) YBRID ILTER SV09957XX* B... -
Page 16: Warranty
All illustrations and specifications in this catalog are based on the latest product information available at time of production. Broan-NuTone, LLC and BEST® reserves the right to make changes at any time, without notice, in prices, colors, materials, equipment, specifications and models, place of manufacture and to discontinue models or equipment.
Need help?
Do you have a question about the ICB3I Series and is the answer not in the manual?
Questions and answers