Table of Contents
Advertisement
Quick Links
Osmo
DEMINERALIZER
USER MANUAL
Dear Owner,
Thank you for purchasing our demineralizer Osmo.
The manufacturer is pleased to provide information concerning the use of this equipment herewith.
We remind you that in order to use the demineralizer correctly, it is necessary to read this manual carefully.
All our products comply with the current safety norms and do not involve any risk for the operator when
used according to the instructions provided.
Whilst wishing you every success in your work, please note that the reproduction of this manual is illegal
and that, due to continuous research and technological development, the equipment specifications could
change without prior notice.
W&H
S.r.l.
STERILIZATION
Osmo
1
Advertisement
Table of Contents
Related Manuals for W&H Osmo
Summary of Contents for W&H Osmo
- Page 1 USER MANUAL Dear Owner, Thank you for purchasing our demineralizer Osmo. The manufacturer is pleased to provide information concerning the use of this equipment herewith. We remind you that in order to use the demineralizer correctly, it is necessary to read this manual carefully.
-
Page 2: Table Of Contents
REPLACEMENT OF FILTER CARTRIDGES.....................15 REPLACEMENT OF THE OSMOTIC MEMBRANE ...................16 MAINTENANCE .............................17 EXTERNAL CLEANING..........................17 ® MAINTENANCE OF THE WATER BLOCK AND ONE-WAY VALVE ............17 SPARE PARTS ............................18 TECHNICAL SPECIFICATIONS........................20 ® MAINTENANCE ISTRUCTIONS FOR THE SAFETY VALVE (WATER BLOCK ) ........21 Osmo... -
Page 3: Introduction
The reproduction, either total or in part, of the texts and the illustrations in this manual is forbidden. Note: If the Osmo demineralizer is used to supply sterilizers with demineralized water, it is imperative to monitor the water quality. If the supplied sterilizers do not feature a water conductivity sensor to monitor the water quality, we recommend using the manual water conductivity meter Primo 5. -
Page 4: Resin-Security Precautions
The number is CER 19 09 04. * extracted from the safety data sheet supplied by the manufacturer. For further information, please request the safety data sheet directly from the manufacturer of distributor of the product. Osmo... -
Page 5: Information On The Warranty
Non-compliance with the instructions included in this manual The replacement of equipment or the extension of the warranty period because of breakdown is excluded. Repair under warranty is carried out at the discretion of the manufacturer and does not include packing and shipment costs. Osmo... -
Page 6: Package Contents
In the event of damage or missing items, inform the carrier and the supplier immediately. PACKAGE SIZE AND WEIGHT Gross weight: 18 kg Dimensions (mm): Osmo... -
Page 7: Delivery Content
(5m, Ø1/4”) Special key for cartridge holders drain tube installation kit Dowels and screws for fixing the system to a wall Drain tube for carbon block cartridge Warranty certificate , CE declaration of conformity and user manual Osmo... -
Page 8: Installation And Use Of The Demineralizer
EN 1717 Recycling symbol SYSTEM COMPONENTS Spray (optional) (optional) Inlet tap Drain water outlet Water Block valve Membrane One-way valve Pump Storage tank 24Vdc 240Vac Power supply unit Figure 2 – Composition of the device Osmo... -
Page 9: Preliminary Installation Instructions
The installation of the product with incoming water pressure above 3 bars, can drastically reduce the lifespan of all the cartridges and especially of the osmotic membrane. If this is the case, the installation of a reducer to bring the pressure to less than 3 bars is recommended. Osmo... -
Page 10: Installation
Mount the brackets from the assembling kit on the drain tube. Pierce the drain tube with a bit Ø Pierce 6mm. Ø6mm Insert the black drain tube from the back of the osmotic membrane and tighten with a ring nut. Osmo... - Page 11 5÷15 min Remove the plug form the plug- hole. Close the device tap Reset the original connection on the carbon block’s cartridge head (disconnect the red tube, reconnect the white tube and tighten with the ring-nut ). Osmo...
-
Page 12: Priming
After setting up the system, it takes 5 minutes to produce demineralized water It takes approx. 140 minutes to completely fill up the system (including the storage tank) Connection to: Spray gun tap (optional) SAT (optional) Figure 4 – Example of installation Osmo... -
Page 13: Examples Of Usage
Manual use with spray gun (standard) for manual filling of the sterilizer tank and washing of instruments Manual usage with tap service tank Automatic use to fill the sterilizer using the SAT (option) Figure 5 – Possible uses of the device Osmo... -
Page 14: Use And Operation Of The Demineralizer
(e.g. Sat) connected to the Osmo device. The quantity of water produced by the cartridges depends on the quality and hardness of the city water supply in the area where you live. -
Page 15: Replacement Of Filter Cartridges
Remove used cartridges, remove and clean the centring bracket rings, replace the cartridges using the rings. Make sure to insert the cartridge in the correct holder ( if it says UP. place the cartridge with the writing at the top). Osmo... -
Page 16: Replacement Of The Osmotic Membrane
Extract the membrane with the help of sure that the gasket is positioned correctly. Re- pliers. tighten the cap and connect the tubing. Gasket Figure 6 – Membrane replacement After membrane replacement, the system needs to be primed! Refer to chapter “Priming” for further instructions. Osmo... -
Page 17: Maintenance
The Water Block serves as an anti-flooding device. Blocking only takes place if there is considerable leakage (such as a cut in the tube between the Water Block and the demineralizer). Blocking does not take place if there is a small leak in the product’s hydraulic system. Osmo... -
Page 18: Spare Parts
OSMOTIC MEMBRANE 75 GPM, 95-98% REJECTION A813018X O-RING A813014X PLASTIC KEY FOR CARTRIDGE HOLDER A812101X STORAGE TANK INCLUDING TAP A813007X ® WATER BLOCK VALVE (INCLUDING FILTER AND A812005X SETTING KEY) SPIRAL TUBE ¼” A812105X WATER GUN A812106X CENTERING RING A813006X Osmo... - Page 19 WATER PIPE (5 m, Ø 6.35 mm) A813020X PRESSURE REDUCER ¾” X ¾” 3 BAR A813025X CATRIDGE KIT COMPLETE A813010X (REF. 3+ 4 + 5+ 6 + 7x3) CARTRIDGE KIT INTERMEDIATE A813019X (REF. 3 + 4+ 5 + 7x3) Osmo...
-
Page 20: Technical Specifications
1 bar (14,7 psi) Tap water pressure maximum 5 bar (73,5 psi) Quantity of produced water with conductibility < 10,000 liters 15µS est conditions: T=25° C, tap water quality 450 µS an d water pressure of 3 bar; with continuous flow; Osmo... -
Page 21: Maintenance Istructions For The Safety Valve (Water Block ® )
‘E’ periodically and to replace the seal ‘F’ .We reserve the right to modify any Produced by features without prior notice. ELTEK s.p.a. Tel. 0142 335511 Fax 0142 335555 15033 Casale Monf. (Italy) salesdept@eltekgroup.it Osmo...
Need help?
Do you have a question about the Osmo and is the answer not in the manual?
Questions and answers