SGS GPA520 Owner's Manual
  1. Manuals
  2. Brands
  3. SGS Manuals
  4. Tools
  5. GPA520
  6. Owner's manual

SGS GPA520 Owner's Manual

Petrol auger
Hide thumbs

Advertisement

Table of Contents

GPA520
PETROL AUGER
OWNER'S MANUAL
FOR YOUR SAFETY
PLEASE READ THESE INSTRUCTIONS CAREFULLY
AND RETAIN THEM FOR FUTURE USE.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GPA520 and is the answer not in the manual?

Questions and answers

Related Manuals for SGS GPA520

Summary of Contents for SGS GPA520

  • Page 1 GPA520 PETROL AUGER OWNER’S MANUAL FOR YOUR SAFETY PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE USE.

  • Page 2: Specification

    SPECIFICATION GENERAL SAFETY PRECAUTIONS WARNING: Fire hazard - keep fuel away from all MODEL No GPA520 sources of ignition. ENGINE SIZE 52 cc MAX POWER 1.8 kW MAX SPEED 7500 RPM You MUST STOP using the machine if: • The engine speed changes with no control.
  • Page 3 2. DO NOT overfill and allow a 25mm gap at the top of the tank. Once full replace and correctly tighten the fuel cap. DO NOT use straight unleaded petrol. From empty the fuel tank holds 800ml. WWW.SGS-ENGINEERING.COM PAGE 4 PAGE 5...

  • Page 4: Maintenance

    Allow the machine to cool down with no throttle applied. Turn the check for any loose parts for repair or replacement. power switch OFF. If not already in RUN position move the choke to the RUN position. WWW.SGS-ENGINEERING.COM PAGE 6 PAGE 7...

  • Page 5: Operation

    Shut down the engine, wait for all moving parts to come to a complete stop, remove HT lead, and then wait for 5 minutes before performing maintenance on the tool. WWW.SGS-ENGINEERING.COM PAGE 8 PAGE 9...

  • Page 6: Fuel Filter

    6. Check the spark plug washer for damage and replace if required. 7. Refit the spark plug by hand to make sure it does not cross thread, tighten the spark plug to a torque of 12/15Nm. WWW.SGS-ENGINEERING.COM PAGE 10 PAGE 11...

  • Page 7: Technical Specification

    Start Method: Recoil Clutch type: Centrifugal Fuel: 40:1 ratio Semi-Synthetic 2 stroke oil/Unleaded petrol Grease: High temperature gearbox grease - 20 grams Drill sizes diameter/length: 100 x 800 mm 150 x 800 mm 200 x 800 mm WWW.SGS-ENGINEERING.COM PAGE 12 PAGE 13...

  • Page 8: Parts Diagram

    Clamp spring 904026 Gasket 903991 Fuel pipe 904027 Intel air pipe 903992 Fix of oil pipe 904028 Gasket of carburetor 903993 Fuel filter 904029 Carburetor 903994 Fuel tank 904030 M5x35 bolt 903995 Bracket of tank 904031 WWW.SGS-ENGINEERING.COM PAGE 14 PAGE 15...
  • Page 9 Gearcase 903948 Bolt M6x30 903949 Output shaft 903950 Oil seal ø19xø37x7 903951 Bolt M6x50 903952 Bolt M6x8 903953 Gear 48T 903954 Gear 7T 903955 Throttle level 903956 Bolt M8x50 903957 Nut M8x6.5 901995 Driller 903959 WWW.SGS-ENGINEERING.COM PAGE 16 PAGE 17...
  • Page 10 SGS Engineering (UK) Ltd West Side Park Raynesway Derby, DE21 7AZ EC Declaration of Conformity This is an important document and should be retained MANUFACTURER’S NAME: SGS Engineering (UK) Ltd PETROL AUGER TYPE OF EQUIPMENT: GPA520 PART NUMBER: APPLICATION OF EC COUNCIL DIRECTIVES / STANDARD:...

Table of Contents