Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Drinkpod 1000 Pro Series
Summary of Contents for Drinkpod 1000 Pro Series
- Page 1 Use & Care Guide English 1000 Pro Series Countertop Purifier·Dispenser·Sterilizer Model: DP1000(B) Customer Assistance 1-844-374-6576 www.drinkpod.com Drinkpod and the Drinkpod logo are the registered trademarks of Drinkpod, LLC. All Rights Reserved.
- Page 2 DP1000 DP1000B...
-
Page 3: Table Of Contents
Issue #2: My filter lifespan seems very short. Issue #3: My 1000 Pro Series isn’t powering on. Issue #4: My 1000 Pro Series’s Hot Mode won’t dispense. Issue #5: My 1000 Pro Series’s Hot Mode isn’t hot. Issue #6: My 1000 Pro Series’s Cold Mode isn’t cold. -
Page 4: Important Safety Instructions
10. Do not install the machine in a location exposed to direct sunlight. Never store or expose your 1000 Pro Series in an environment less than 32°F. 12. This appliance is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. -
Page 5: Getting To Know Your 1000 Pro Series
Getting To Know Your 1000 Pro Series Behind Dispenser Nozzle Getting To Know Your 1000 Pro Series 1... - Page 6 Important Safety Instructions Important Safety Instructions 2...
- Page 7 Important Safety Instructions Leak Detector Compartment Product Features Control Panel Dispenser Light Button - Toggles dispenser light. ECO Mode/Filter Rest Button - Press to toggle ECO Mode, hold to reset filter. Light Sensor - Light sensor that activates ECO Mode. Important Safety Instructions 3...
- Page 8 Important Safety Instructions Heating System Status Light - When lit, indicates heating system is active. Cooling System Status Light - When lit, indicates cooling system is active. System Power Status Light - When lit, indicates is powered on. UV Sterilizer Status Light - When lit, UV sterilizer is active (ambient only). Pod Filter(s) Status Light - When light is red, pod filters needs replaced.
- Page 9 External Filter Source Line - OPTIONAL external filter source bridge line. External Filter Appliance Line - OPTIONAL external filter appliance bridge line. Dispenser Light - Illuminated dispense area. Appliance Drain Port - Port to drain 1000 Pro Series prior to storing or relocating. Important Safety Instructions 5...
-
Page 10: Filters
Important Safety Instructions Filters Shown above are the available pod filter options in Drinkpod’s water purification product line. F1. ULTRA+3 Hybrid Scrub (Included)- Recommended for internal filter slot. May be replaced by Polishing Scrub for increased flow rate (at the cost of purification quality). - Page 11 Important Safety Instructions F3. Chemical Scrub (Sold Separately)- This filter can be used as an alternative, replacing the secondary Particle Scrub. The Chemical water filter replacement pod utilizes a activated carbon granules to improve the safety of drinking water by effectively removing common disinfection byproducts (THMs), organic contaminants like chlorinated solvents and other industrial pollutants, pesticides, and select heavy metals such as lead and mercury.
-
Page 12: Technical Specifications
The manufacturer is not responsible for any issues or damage that may occur to other appliances connected to your Drinkpod 1000 Pro Series. These issues may include, but are not limited to: dry heating, low flow, water sloshing, etc. Drinkpod are in now way obligated to provide technical support, warranty service or replacement for any parts or components not included with your 1000 Pro Series, excluding OEM replacement filters. -
Page 13: Powering On/Off Your 1000 Pro Series
What temperature of water is dispensed (temperature modes), and the amount of water that is dispensed (dispense modes) can be selected by pressing the temperature and dispense mode buttons. By default, your 1000 Pro Series is set to (and will always return to) QuickFill Mode... -
Page 14: Customizing Quickfill Mode
5. Finally, press and release the QuickFill Mode Button to save your new fill time. You’re all set! Controlling Dispenser Light Your 1000 Pro Series is equipped with a Dispenser Light. It has 3 different modes Using Your 1000 Pro Series 10... -
Page 15: Using Eco Mode
Button will re-illuminate. Dispenser Light Button Using ECO Mode Your 1000 Pro Series is equipped with an environmentally aware energy saving feature called Mode. This feature will power down the heating and cooling systems when it senses the room’s ambient light has been significantly reduced. It will power back up the heating and cooling system once it senses the ambient light levels have returned to their normal level. - Page 16 Using Your 1000 Pro Series Using Your 1000 Pro Series 12...
-
Page 17: Replacing Your 1000 Pro Series's Filters
Scrub, or alternative and the ULTRA+3 Hybrid Chemical Scrub (if purchased separately), prior to installing them into your 1000 Pro Series. Polishing Scrub For this step, you will need a towel, a container to catch water, and your Filter Flushing Setup you assembled during installation. - Page 18 15. Plug back into the electrical outlet. 110v Power Cord 16. Finally, press and hold the ECO Mode/Filter Rest Button for 5 seconds to reset the timer and Pod Filter(s) Status Light. You’re finished! Maintaining Your 1000 Pro Series 14...
-
Page 19: Storing & Relocating Your 1000 Pro Series
Storing & Relocating Your 1000 Pro Series At some point, you may need to store or relocate your 1000 Pro Series. Should one of these situations be the case for you, below are a few simple steps to prevent any damage from occurring. - Page 20 8. Now, press and hold the Dispense Button (with Cold Mode selected) until water flow from the drain port stops, indicating your 1000 Pro Series has been fully drained. 9. Replug the Appliance Drain Port by repeating “Step 7” in reverse.
-
Page 21: Leaving Your 1000 Pro Series (Vacation)
Leaving Your 1000 Pro Series (Vacation) If you plan to take a trip, and leave your 1000 Pro Series for more than a few days, We highly recommend following the steps below prior to leaving. This will help prevent any damage from occurring, the rare possibility of leaks, and returning to poor tasting water. -
Page 22: Troubleshooting Your 1000 Pro Series
Solution 2: Something may be restricting water flow. Is a section of tubing pinched? Are all of the valves between your water source and the 1000 Pro Series open as far as they’ll Solution 3: Your filter(s) may need replaced. Filter(s) will slowly become more clogged by the contaminants they filter out, slowing water flow. -
Page 23: Issue #3: My 1000 Pro Series Isn't Powering On
Solution 3: If you haven’t already, try attaching the secondary external Particle Filter and external attachment assembly to your 1000 Pro Series. It was included to specifically address scenarios a users water source has abnormally high levels of large particle contaminants, to extend the primary filters lifespan. -
Page 24: Issue #7: My Dispenser Button Light Is Flashing
Once you’ve resolved all leaks, reattach exterior panels. Now, rotate and slide the 1000 Pro Series so that the rear left corner is extruding our over the counter. Insert a small flat head screwdriver into the small slot in between... - Page 25 Solution 2: Check for disconnected tubing or water line or filter connection throughout unit. Solution 3: Check for broken, cracked or weak fitting connections. Solution 4: Contact support at 1-844-374-6576, or email us at support@drinkpod. com. Troubleshooting Your 1000 Pro Series 21...
-
Page 26: Notes
Notes Notes 22... -
Page 27: Warranty
Damage to or failure of this appliance resulting from installation not performed by Drinkpod authorized service agents, including installation that was not in accord with electrical, gas or plumbing codes.
Need help?
Do you have a question about the 1000 Pro Series and is the answer not in the manual?
Questions and answers