Related Manuals for Rico Beam 230
Summary of Contents for Rico Beam 230
-
Page 1: User Manual
Beam 7R Moving Light User Manual Please read this user manual before using this product. -
Page 2: Table Of Contents
INDEX STATEMENT ACCESSORIES SAFETY INSTRUCTION GENERAL GUIDELINES INSTALLATION TECHNICAL SPECIFICATION CONTROL SYSTEM PANEL OPERATION CHANNEL DESCRIPTION: CLEANING AND MAINTENANCE... -
Page 3: Statement
STATEMENT product well capability intact packing when leave factory. All of the user should comply with warning item and manual, any misuse cause of the damages are not included in our guarantee, and also cannot be responsible for any malfunction & problem owing to ignore the manual. -
Page 4: General Guidelines
GENERAL GUIDELINES NEVER OPEN THIS FIXTURE WHILE IN USE! During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture. This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and will decrease gradually over time. - Page 5 fixture while operating, to prevent any fire hazard. The fixture must be installed in a location with adequate ventilation, at least 1.5 feet (.5m) from adjacent surfaces. Be sure no air ventilation slots are blocked. DO NOT attempt installation and/or operation without knowledge how to do so.
-
Page 6: Installation
INSTALLATION C A U T I O N S For added protection, mount the fixture in areas outside walking paths, seating areas, or in areas were unauthorized personnel might reach the fixture. Ambient operating temperature range for this fixture is 5°... - Page 7 safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people Clamp mounting The moving head provides a unique mounting bracket assembly that integrates the bottom of the base, the included ‘Omega Bracket’...
- Page 8 DMX-512 control connection: Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the moving head. You can chain multiple Moving head together through serial linking. The cable needed should be two core, screened cable with XLR input and output connectors.
-
Page 9: Technical Specification
TECHNICAL SPECIFICATION Light Sources: Philips MSD Platinum 5R or Osram 7R ( Color temperature: 8000K) Power Voltage: AC 100-240V, 50/60Hz Power Consumption: 350W Product Size：523×337×511mm Packing Size: 635X440X725 Net weight：19.5KG Control DMX Channel: 16 DMX Channel Control Modes: DMX-512 Control Signal: DMX512/Master-Slave/Auto run Pan/Tilt Pan/Tilt: 540°/ 270°... -
Page 10: Control System
Feature Amazing dot matrix, four tact switch, 180° turning show 0-100% mechanical dimming, mechanical dimming and free dimming available. Strobe macro control available. Lens optical system electric focus .beam angle 0～4° Over heat protection Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice CONTROL SYSTEM The DMX512 is widely used in intelligent lighting control, with a DMX 512... -
Page 11: Panel Operation
PANEL OPERATION Brief The light panel diagram show as Figure 1, Left area is TFT Displayer, support touch, and right area is encoder button, both of touch and coder button can operate light and setting. Display & operation just like ‘Android operation system’, touch the item will set or modify setting. - Page 12 Parameter value setting When the selected item is value need to been modified, the dialog shown in Figure 2 will popup. Figure 2 Dialog of value setting ⚫ Modify value：Can quickly modify value via pull the slider to the desired position, or click the button of ‘up’...
- Page 13 Figure 3 Dialog of confirm Sub Menu（Parameter） Chick item of main menu, enter corresponding sub menu, shown in Figure 4, total 6 sub menu, includes class of parameter and status: ⚫ ADDRESS：Set light DMX address. ⚫ WORKMOD：Set light work mode, master or slave mode when in auto run mode.
- Page 14 Figure 4 Parameter menu Operation and parameter instruction Via following operation, enter sub menu(parameter menu) shown in Figure 4 ⚫ In main menu, chick 1/6 function button into corresponding parameter menu. ⚫ In sub menu(page), chick main item on the left side of displayer, can shift to corresponding sub menu(page) quickly.
- Page 15 Light includes 3 work mode: DMX MODE, AUTO RUN and SOUND MODE, Parameter definition as following: ⚫ DMX Mode ： Under this mode, the light receive data from the DMX controller and move. ⚫ AUTO RUN：Under this mode, light will run with inside code(data), ignore data from DMX controller.
- Page 16 ⚫ Screen Saver：when panel is idle(these is no operation in 10 second), displayer will enter saver status. When set as ‘mode 1’，saver status is close display, as ‘mode 2’ saver status will display DMX address code(DMX MODE) or display LOGO(AUTO RUN or SOUND CTRL). As ‘OFF’, keep light up displayer and show main menu。...
- Page 17 Figure 8 page of Test Set light run parameter Enter the page as shown in Figure 8, set the parameter of light: Pan Invert: Reverse PAN move. ⚫ ⚫ Tilt Invert: Reverse TILT mover. ⚫ Rectify enable：set as ‘OFF’, PAN or TILT will disable position rectify function.
-
Page 18: Channel Description
Figure 9 page of run parameter View status Enter the page as shown in Figure 10: ⚫ View light current status, version； ⚫ DMXClr: Click to clear all DMX data to ‘0’. ⚫ SysRst：Click to reset light. Figure 10 page of status CHANNEL DESCRIPTION: 1. - Page 19 20~24 COLOR2 25~29 COLOR2 + COLOR3 30~34 COLOR3 35~39 COLOR3 + COLOR4 40~44 COLOR4 45~49 COLOR4 + COLOR5 50~54 COLOR5 55~59 COLOR5 + COLOR6 60~64 COLOR6 65~69 COLOR6 + COLOR7 70~74 COLOR7 75~79 COLOR7 + COLOR8 80~84 COLOR8 85~89 COLOR8 + COLOR9 90~94 COLOR9 95~99...
- Page 20 2. DIMMING & STROBE The light support multiple strobe mode, as show Table 2 in detail.。 Table 2 detail of strobe CH NO. NAME VALUE FUNCTION Dark 4~103 Slow strobe to fast strobe 104~107 White 108~207 Slow strobe to fast strobe(mode 2) STROBE 208~212 white...
- Page 21 27~29 Gobo9 30~32 Gobo10 33~35 Gobo11 36~38 Gobo12 39~41 Gobo13 42~44 Gobo14 45~47 Gobo15 48~50 Gobo16 51~53 Gobo17 54~59 Rotate forward（Fast -- slow） Rotate reverse（Slow -- fast） 60~85 86~95 Gobo1,shaking slow to fast 96~105 Gobo2,shaking slow to fast 106~115 Gobo3,shaking slow to fast 116~125 Gobo4,shaking slow to fast 126~135...
- Page 22 4. Light effect The light support electronic focusing, insert prism, insert frost, as show in detail Table 4 detail of light CH NO. NAME VALUE FUNCTION PRISM 0-63 Open 64-127 Insert Prism1 128-191 Insert Prism2 192-255 Insert both Prism1 & Prism2 PRISM.R 0~127 Angle 0~400...
-
Page 23: Cleaning And Maintenance
If too long (over 5 minutes) using the dimming to close light, should use the "lamp control" channel to turn off the lamp. Table 6 detail of remote CH NO. NAME VALUE FUNCTION CH15 RESET 0~239 none Reset light （stay over 3 second） 240~200 CH16 LAMP... - Page 24 MAINTENANCE Regular inspections are recommended to insure proper function and extended life. There are no user serviceable parts inside this fixture, please refer all other service issues to an authorized service technician. Should you need any spare parts, please order genuine parts from your local dealer. Please refer to the following points during routine inspections: •...
Need help?
Do you have a question about the Beam 230 and is the answer not in the manual?
Questions and answers