Advertisement
Therefore,
if
disabling keypad
panic, cut Jumper
A
after
programmin g
zone
descriptions.
Disable
Tactile
Beep.
Cut Jumper
B to
silence the tone
that
sounds
whenever
a
keypad
button
is pressed.
Disable Keypad Fire.
Cut
Jumper D
to
disable
the
keypad
fire
buttons
(Fire
Emergency), Keys
[*]
and
[A].
Disable
LCD
Backlight. Cut Jumper
W2 to
disable
LCD
display back
lighting.
Disable Touchpad
Backlight.
Cut
Jumpers
W1
and
W3
to
disable touchpad
backlighting.
Kepad
Assignment.
Up
to
7 keypads may be connected to
the
panel.
If
more than
one
keypad
is
installed"
(a)
each
must
be
assigned
its
own unique keypad
address
number
(that
is,
no two keypads
may be
numbered
alike);
(b)
keypads must
be
numbered consecutively (that
is,
missing
numbers
are
not
permitted);
and
(c)
only Keypad
No.
1
can be used
for
programming.
In
multiple keypad configurations, the total number of
keypads must
be
programmed into
the
contol
panel in address
995.
The number
in
address 995
must
agree
with the total
number of
keypadsin
the system,
or
a
[KEYPAD
FAIL XX]
system
trouble
will
result.
RP2000LCD
address
numbers
are
"programmed"
by
selection
of
the
Address
Jumpers, the
four-block
jumper strip at
the
extreme
lower-right corner
of
the
board (viewed
from
the
inside
bottom). Referring
to
the
following
table,
program
the
keypad address
by
shoning
the
respective
pair(s)
of terminals
with
a
jumper,
as
indicated by "[:]" fiumper on);
":"
indicates
open Qumper off).
RP2000LCD
Address
Jumper
No.
321P*
L
: :
[:][:]
2
:[:]:
[,]
3
: [:][:]:
4
[:]: :
[']
5
[:]:[:]:
6
[:][:]:
:
1
[:][:]
[:]
:
*Parking
position
for
unused
jumper(s)
(located nearest
the
corner).
[:]
:
Jumper on
(shorted);
:
:
Jumper
off
(open)
LCD
ADJUSTMENT
The viewing
angle
for
the
LCD
display
is adjustable by means
of the
LCD ADJUST
screwdriver
control
on the back of the
circuit board (refer
to Label LA809
affixed
to
the
board).
Viewing the board
at its normal mounting height, turn
the
control
clockwise
or
counterclockwise
for optimum
contrast.
TESTINGTHE KEYPAD
To
test
the keypad after installation,
simultaneously
press
Keys
[*]
and [3]. This
will initiate
a
test
that
checks
all
LCD
ele ments, the
sounder,
and
both
LEDs.
Repeatedly
pressing
these keys
will
change
the
pattern
displayed
on
the
LCD. To
terminate
the test, press
the
IRESET] Button.
COMPLETING THE
INSTALLATION
To
reassemble
the keypad
after installation,
hang the
top
of
the
front
panel
onto
the hooks
in the rear
case
and push
in
firmly
at
the
bottom until
the
retainer
tabs snap
into
place.
(If
difficulty is
encountered,
push the retainer
tabs
up
slightly
using
a
screwdriver,
as
when
removing.)
Circuit Board
Jumper
Block
Front
Panel
Address
jumpers
as viewed
li'onr
the inside
bottom.
RP2000LCD
#1
is
shown.
Advertisement
