Advertisement
Quick Links
DESCRIPTION
The
RP2000LCD is
a
user-friendly
backlit
keypad designed
for
Napco's MA2.600-Series
control
panels.
A
large
al-
phanumeric
liquid-crystal display
(LCD)
functions as
a
readout
for
control-panel
information and zone identifica-
tion,
and can also serve
to display
messages
downloaded
from
a central monitoring station. The keypad functions
as
a
programmer
as
well
in its
secondary
mode
of operation. In-
stallation
is
quick
and
easy
on only
four
wires.
fer
to
and
operation,
and
to
the manual
furnished
with
the
control
panel
for
panel
installation
and
dealer programming
informa-
tion.
SPECIFICATIONS
Operating
Voltage:
9.0-13.0Vdc
(supplied
by
control
panel)
Current:
64mA typ.,
normal backlighting
Dirnensions
(HxWxD)
:
4-3/8'
x
5-7
18"
x
l,-Ll
16"
MOUNTING
Opening the
Keypad.
There
are
two
slots along
the bottom
edge
of the
kelpad
about
1
inch
from
each side.
To
open,
insert
a
mediun
screwdriver
into
either slot
and push up
with
a
slight twisting
motion
to release the
retainer
tab. Repeat
for
the
other
slot.
Pull
out
at the
bottom
and
lift
off
the
two hooks
at
the top.
When
installing
the
rear
case,
be sure
that
the
words "TOP"
and
"LJPU
(molded
into the
case)
are
properly oriented. The
rear
case is
provided with
a
variety
of
holes
to
accommodate
virtually
any
mounting
situation. The four
holes nearest the
center
are
designed to
fit
a
double-gang
box.
The
four slotted
holes
are
for mounting
directly into
a
wall
with
screws
suitable
for
the surface
material;
the slots allow
levelling
adjustment.
The
four
corner
holes may
similnlly
fe
used
for wall
mounting,
but provide
no
levelling
adjustment.
WIRING
Wire
the
kelpad to
the
control panel
as
follows:
KeypadWire
Color
Code
Black
o
Red
(+)
Yellow
Control-Panel
Terminal
43
44
45
Green
6
NOTE:
If
using
x
soldelingiron,
be
careful not
to splash
solder
onto the
kelpad circuit board or
components; as
damage
could
result.
Remote Emergency
Buttons.
For remote
emergency
(police
panic) buttons, install momentary-contact
switches
to
Ter-
minals 42 and43 on
the control
panel.
Backlighting. Backlighting requires
no additional wiring. In
normal
use,
the
kelpad
is
always
dimly
backlit.
Pressing
any
key
will
increase
the brightness
to facilitate
code
entry,
but
after
30 seconds
of
kelpad inactiviry,
brightness
will
again be
reduced.
To
disable
backlighting,
see
JUMPER OPTIONS.
JUMPER OPTIONS
Several
jumpers provide
a
wide variety
of options. They
are
conveniently
located around the
perimeter
of
the
board
for
easy access.
To identify the location of
the
jumpers, refer to
the
label (LA809)
af|xed to
the
fishpaper
on the back
of
the
board. (NOTE: Jumper
C is
not
an
option;
it
must be
intact
at
all
times.)
Disable Keypad
Panic.
Cut
Jumper
A
to
disable the keypad
panic
buftons
(Police
Emergency),
Keys
[*]
and
[C].
NOTE:
This
will
also disable
the Copy Text function
in
the Zone-
Description Program Mode (see User's Guide,
OI137).
Advertisement
