Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Network Devices Manuals
  4. Matrix Switcher
  5. ND-66-B70
  6. User manual

Network Devices ND-66-B70 User Manual

6×6 hdmi 18gbps over hdbaset matrix with audio matrixing
Hide thumbs

Advertisement

Quick Links

Download this manual
ND-66-B70
6×6 HDMI 18Gbps
over HDBaseT™Matrix with Audio
Matrixing
VER 2.1
3

Advertisement

loading

Related Manuals for Network Devices ND-66-B70

Summary of Contents for Network Devices ND-66-B70

  • Page 1 ND-66-B70 6×6 HDMI 18Gbps over HDBaseT™Matrix with Audio Matrixing VER 2.1...

  • Page 2: Table Of Contents

    Thank you for purchasing this product For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surge protection device recommended This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc.

  • Page 3: Introduction

    1. Introduction The6x6 HDMI/HDBaseT matrix supports the transmissionof video(resolutions up to 4K2K@60Hz 4:4:4, HDCP 2.2, HDMI2.0) and multi-channeldigital audio from 6 HDMI sources to 4 HDBaseT outputs and2 independentHDMI2.0 outputs. HDBaseT outputs allow transmissionvia a single CAT5e/6/7 cable up to 230 feet/70meters and the independent HDMIoutputs support cable lengths of up to 33 feet/10 meters.

  • Page 4: Package Contents

    3. Package Contents  1 x 6x6 Matrix Unit  4 x 70M HDBaseT Receivers  7 x Wideband IR Blaster cables  8 x Wideband IR Receiver cables  1 x RS-232 male to female cable  1 x AC power cable ...

  • Page 5: Operation Controls And Functions

    2x HDMI Type A [19-pin female] 4x HDBaseT Out [RJ45] Outputs 6x L/R Audio Out [3.5mm Stereo Mini-jack] 6x Optical Out [S/PDIF] 7x IR Out[3.5mm Stereo Mini-jack] Mechanical Housing Metal Enclosure Color Black Dimensions 483 mm [W] x 303 mm [D] x 44.5 mm [H] Weight 2110g Power Supply...
  • Page 6 Menu:Select EDID、PTP Set、Save Preset、Recall Preset、View IP and Set up the map of input and output and Inquire each input's EDID status. a. Select EDID: On the initial OLED display you can press “Menu” button to enter Setup Menu page. You can press the “Up” and “Down” buttons into select EDID mode page, the EDID table as showed in the below table, you can press “Right”...
  • Page 7 Setup Menu page. You can press the "Up" or "Down" into the PTP Set page. and press the "Right" to confirm this operation. If success the screen will go back to PTP Set page, you can press "Left" button to go back the initial OLED display. c.

  • Page 8: Rear Panel

    5.2 Rear Panel 1. HDMI In: Connect to HDMI source devices such as Blu-ray DVD or PS4. 2. 2 HDMI and 4 HDBaseT Out: 2 HDMI out connect to HDMI display devices and 4 HDBaseT connect to the HDBaseT receivers. This is a two-way transmission port.
  • Page 9 5.3 HDBaseT Receiver Panel 1. POWER LED: The LED will illuminate after the receiver is powered on. 2. DC 24V: In the matrix system, the jack doesn’t be used because of the power from matrix POC output. 3. HDBaseT IN: Connect to the matrix HDBaseT output port. 4.
  • Page 10 IR Receiver and Blaster pin’s definition as below: 5.6 IR and RS-232 Instructions The above connection diagram shows the IR and RS-232 connections: 1. IR Connection: A. The IR INPUT / OUTPUT (1/2/3/4/5/6) of the matrix is associated with the IR OUTPUT / INPUT of each HDBaseT receiver , and form the IR matrix port together.

  • Page 11: Pc Control Software And Web Gui

    D. IR ALL OUT: This port is used for all HDBaseT Receiver IR in It means that all HDBaseT receiver's IR in signal can be output from the matrix's this port. 2. RS-232 Connection: The matrix RS-232 (C/D/E/F) port is corresponding to each HDBaseT receiver’s RS-232 port.
  • Page 12 UART mode 2. TCP/IP mode a. The matrix default DHCP is enabling, after powering up 3 minutes if network router doesn’t assign an IP address to the matrix, it will use an IP address (192.168.1.100) as default IP. b. The matrix and the PC on the same network IP segment with network router and the matrix work on the DHCP status.
  • Page 13 TCP/IP mode 6.2 Web GUI Before accessing matrix Web GUI, you should know current matrix IP address, you can get it from the front OLED panel “Menu” ->“View IP” page. Then you should set the IP address of your PC or laptop or mobile device is within the same IP address segment with the matrix.

  • Page 16: Connection Diagram

    7. Connection Diagram...