Protekt AT251 Instruction Manual

it is obligatory to verify the free space required beneath the user at the workplace before each occasion of use the fall arrest system, so that, in the case of a fall, there will
be no collision with the ground or other obstacle in the fall path. The required value of the free space should be taken from instruction manual of used equipment.
there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be observed during equipment utilization,
especially:
- trailing or looping of lanyards or lifelines over sharp edges; - any defects like cutting, abrasion, corrosion;
- pendulum falls; - extremes of temperature; - chemical reagents;
personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or cases made of steel or plastic) to protect it against
damage or moisture.
the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile products use mild detergents for delicate
fabrics, wash by hand or in a machine and rinse in water. Plastic parts can be cleaned only with water. When the equipment becomes wet, either from being in use or when
due cleaning, it shall be allowed to dry naturally, and shall be kept away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can be
regularly slightly lubricated to ensure better operation.
Other maintenance and cleaning procedures should be adhered to detailed instructions stated in the manual of the equipment.
personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light, ultraviolet degradation, damp environment, sharp
edges, extreme temperatures and corrosive or aggressive substances.
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS REQUIRED.
THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A COMPETENT PERSON, RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT.
ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS, REPAIRS, REASONS OF EQUIPMENT'S WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON.
THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT UTILIZATION.
DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY CARD.
ALL RECORDS IN THE IDENTITY CARD CAN BE FILLED IN ONLY BY A COMPETENT PERSON.
IDENTITY CARD
MODEL AND TYPE OF EQUIPMENT
REF. NUMBER
SERIAL NUMBER
USER NAME
DATE OF PURCHASE
PERIODIC EXAMINATION AND REPAIR HISTORY
REASON FOR
DATE
ENTRY PERIODIC EXAMINATION
OR REPAIR AND OTHER REVELANT INFORMATIONS
1
2
3
4
PROTEKT
93-403 £ódŸ, ul. Starorudzka 9
TEL.: (+48 42) 680 20 83
FAX: (+48 42) 680 20 93
e-mail: info@protekt.com.pl
- climatic exposure;
- electrical conductivity.
LENGTH
DATE OF MANUF.
DATE OF PUTTING INTO OPERATION
DEFECTS NOTED, NAME AND SIGNATURE
REPAIRS CARRIED OUT OF COMPETENT PERSON
The Notified Body involved in equipment's European
certification and production control phase is:
Central Institute for Labour Protection - National Research Institute
ul. Czerniakowska 16, 00-701 Warsaw
Instruction Manual
Read and understand
the manual before
using the equipment
EN 795:2012 type B
Ref. AT251
Anchor beam AT251 is a component of the personal protective equipment against falls from a height complied with
EN 795:2012 as anchor device type B.
It is used for connecting a fall arrest system (e.g. energy absorber with lanyard, fall arresters, cables of fall arresters) on
horizontal prestressed concrete slabs pursuant to Directive of the European Parliament 2001/45/EC.
The device is suitable for protection of max. three persons.
DESIGN
The device is made of aluminium profiles constituting a telescopic connection allowing the beam length to be adjusted.
The device is adapted to prestressed concrete slabs of 1200 mm in width and any slab's height.
Anchor point for PPE
Steel cable
Adjusting bolt
Marking of the yearly
manufacturer's inspection
2015
PERIODIC
EXAMINATION
NEXT DUE DATE
TIME OF USAGE - The anchor beam can be used for 5 years from the date of the first use.
Following the first five years of usage the manufacturer's inspection must be carried out.
The inspection can be carried out by:
- the anchor point manufacturer,
- person authorized by the manufacturer;
- company authorized by the manufacturer;
During the manufacturer's inspection time of usage of the device until the next inspection shall be arranged. The
beam must be withdrawn from use immediately and destroyed if it has been used to arrest a fall.
A n c h o r b e a m f o r
prestressed concrete slabs
1211
1141
Adjustable beam Main beam
Adjusting plate
Fastening plate
MARKING OF THE DEVICE
- marking of the manufacturer
AT251 - reference no.
1437
EN 795:2012/B - number: year of issue of European standard / device type
- note: read the manual before using the equipment
max. 3 x
"xx xxx xxx"
mm/yyyy
- date of manufacture
Anchorage eye bolt
Fastening plate
- CE mark and notified body number
inspecting the equipment manufacturing
admissible number of persons
protected by AT251
- serial number