Protekt P-51E ISOL Instruction Manual

there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be observed during equipment utilization, especially:
- trailing or looping of lanyards or lifelines over sharp edges,
- any defects like cutting, abrasion, corrosion,
- climatic exposure,
- pendulum falls,
- extremes of temperature,
- chemical reagents,
- electrical conductivity.
personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or cases made of steel or plastic) to protect it against damage or moisture.
the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile products use mild detergents for delicate fabrics, wash by hand or in a
machine and rinse in water. Plastic parts can be cleaned only with water. When the equipment becomes wet, either from being in use or when due cleaning, it shall be allowed to dry naturally, and shall
be kept away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can be regularly slightly lubricated to ensure better operation.
Other maintenance and cleaning procedures should be adhered to detailed instructions stated in the manual of the equipment.
personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light, ultraviolet degradation, damp environment, sharp edges, extreme temperatures and
corrosive or aggressive substances.
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS REQUIRED.
THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A COMPETENT PERSON, RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT.
ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS, REPAIRS, REASONS OF EQUIPMENT'S WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON.
THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT UTILIZATION.
DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY CARD.
ALL RECORDS IN THE IDENTITY CARD CAN BE FILLED IN ONLY BY A COMPETENT PERSON.
IDENTITY CARD
MODEL AND TYPE OF EQUIPMENT
REF. NUMBER
SERIAL NUMBER
USER NAME
DATE OF PURCHASE
PERIODIC EXAMINATION AND REPAIR HISTORY
REASON FOR
DATE
ENTRY PERIODIC EXAMINATION REPAIRS CARRIED OUT
OR REPAIR AND OTHER REVELANT INFORMATIONS
1
2
3
4
EC type examination carried out by CETE APAVE SUDEUROPE, BP 193, 13322 Marseille, France - 0082
PROTEKT, 93-403 LODZ, ul. Starorudzka 9, POLAND, TEL: (48 42) 680 20 83, FAX:
DATE OF MANUF.
DATE OF PUTTING INTO OPERATION
DEFECTS NOTED, NAME AND SIGNATURE
OF COMPETENT PERSON
(48 42) 680 20 93, www.protekt.com.pl
Instruction Manual
READ CAREFULLY BEFORE USE
Safety harness is basic of fall arrest equipment and complies with EN
361 and EN 358.
DESCRIPTION
Full body harness P-51E ISOL is made of pieces of polyamide
webbing which are sewn and connected by metal buckles.
This configuration guarantee full safety and comfort work.
BASIC EQUIPMENT
back attaching buckle - for attaching fall arrest system;
front attaching loops - for attaching fall arrest system;
connecting and adjusting buckles - for comfort wearing and using
of harness;
work positioning belt.
SIZES
The harness P-51E is manufactured in two sizes:
- universal: M-XL
- extra large: XXL
ADMISSIBLE TIME OF USE
Safety harness can be used for 5 years counting from a date of
putting the harness into operation. After this period the harness
be withdrawn from use to carry out
inspection .
The manufacturer's inspection can be carried out by:
- manufacturer
- or person recommended by manufacturer
- or company recommended by manufacturer.
During this inspection will be established admissible time of harness
use till next manufacturer's inspection.
The harness must be withdrawn from use immediately and destroyed
when it has been used to arrest a fall.
CONTENT OF HARNESS IDENTITY LABEL
trade mark of the device
type of the device
reference number
PERIODIC
size
EXAMINATION
NEXT DUE DATE
month/year of the device manufacture
number of the manufacturing series
number / year of the European standards
the equipment conform
CE marki n g and number of a not i f i e d body
cont r ol l i n g manufact u ri n g of t h e equi p ment (art . 11)
caution: read the manual
marking of the manufacturer
or distributor
SAFETY
THE EQUIPMENT
HARNESS
EN 361:2002
EN 358:2000 Ref.: AB 151 03
shoulder
strap
shoulder
strap
adjusting
buckle
belt
strap
tight strap
connecting/
adjusting
must
buckle
manufacturer's detailed
tight
strap
P-51E ISOL
SAFETY HARNESS
Ref. AB 151 03
Size: M-XL
XXL
identity
Date
label
of manufacture: 03/2003
Serial
number: 0000001
EN 361:2002 EN 358:2000
P-51E ISOL
front view
front
connecting
buckle
front
attaching
loops
belt
connecting/
adjusting
buckle
belt
side
attaching
buckles
back view
back
attaching
buckle
crossing
plate
belt
pad
tool bag
attaching
D-rings