Table of Contents

Advertisement

3I770A / 3I770CW
Intel® Embedded Ivy Bridge Processor,
DDR3 SODIMM 1333/1600MT/s ,
2 x LAN / HDMI /Audio /USB / COM/LVDS/Touch Screen
All-In-One
Intel® Embedded Ivy Bridge rPGA988B Processor,
2 x Intel GbE LAN , 2 x PCIe mini card slots , VGA, HDMI, Audio, SATA,
USB, 6 x COM ,Wide Range DC-IN, LVDS, Touch Screen
NO. 3I770A/CW_V0.1
Release date: Mar. 4. 2015

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 3I770A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Lex 3I770A

  • Page 1 3I770A / 3I770CW Intel® Embedded Ivy Bridge Processor, DDR3 SODIMM 1333/1600MT/s , 2 x LAN / HDMI /Audio /USB / COM/LVDS/Touch Screen All-In-One Intel® Embedded Ivy Bridge rPGA988B Processor, 2 x Intel GbE LAN , 2 x PCIe mini card slots , VGA, HDMI, Audio, SATA, USB, 6 x COM ,Wide Range DC-IN, LVDS, Touch Screen NO.
  • Page 2: Table Of Contents

    2-2 UNPACKING CHECKUP ...................... 2-3 DIMENSION-3I770A/CW ..................... 2-4 LAYOUT-3I770A/CW ......................2-5 DIAGRAM-3I770A ........................ 2-5-1 DIAGRAM-3I770CW ......................2-5-2 BOTTOM SIDE DIAGRAM-3I770A/CW ................2-6 INSTALL MEMORY ......................2-7 LIST OF JUMPERS ......................2-8 JUMPER SETTING DESCRIPTION ..................2-9 COMS DATA CLEAR ......................
  • Page 3 3-12 LAN INTERFACE ......................... 3-13 USB INTERFACE ........................3-14 SATA INTERFACE ........................3-15 MODULE SOCKET ........................3-16 SIM SOCKET ..........................3-17 SODIMM SOCKET ........................CHAPTER 4 INTRODUCTION OF BIOS ..................4-1 ENTER SETUP ..........................4-2 BIOS MENU SCREEN ........................4-3 FUNCTION KEYS .......................... 4-4 GETTING HELP ..........................
  • Page 4 4-10 SECURITY ..........................4-11 SAVE & EXIT ..........................CHAPTER 5 DRIVER INSTALLATION .................... 5-1 INF INSTALL INTEL BAYTRAIL CHIPSET DRIVER ..............5-2 VGA INSTALL INTEL LVY BRIDGE VGA DRIVER ................ 5-3 SOUND INSTALL REALTEK HIGH DEFINITION AUDIO DRIVER ..........5-4 USB 3.0 INSTALL INTEL USB 3.0 EXTENSIBLE HOST CONTROLLER DRIVER ....... 5-5 ME INSTALL INTEL MANAGEMENT ENGINE INTERGACE DRIVER ........
  • Page 5 Copyright This manual is copyrighted and all rights are reserved. It does not allow any non authorization in copied, photocopied, translated or reproduced to any electronic or machine readable form in whole or in part without prior written consent from the manufacturer.
  • Page 6: Warning

    Warning ! 1. Battery Batteries on board are consumables. The life time of them are not guaranteed. 2. Fless solution with HDD The specifi cation & limitation of HDD should be considered carefully when the fanless solution is implemented. We will not give further notifi cation in case of changes of product information and manual.
  • Page 7: Hardware Notice Guide

    Hardware Notice Guide 1. Before linking power supply with the motherboard, please attach DC-in adapter to the motherboard fi rst. Then plug the adapter power to AC outlet. Always shut down the computer normally before you move the system unit or remove the power supply from the motherboard.
  • Page 8 Photo 1 Insert Unplug...
  • Page 9: Chapter 1 General Information

    Chapter-1 General Information The 3I770A/CW is All-In-One board which could apply to the use of Networking, POS or Automation Control Board. It is designed to combine all necessary input and output affects interfaces, which makes it to be ideal All-In-One control board for the demand of Networking, POS and Automation Control applications.
  • Page 10: Major Feature

    1-1 Major Feature 1. The Mobile Ivy Bridge processor includes Integrated Display Engine, GPU and Integrated Memory Controller and is designed for mobile, the processor is designed for the Chief River platform and may be offered in a rPGA998B package 2.
  • Page 11: Specification

    1-2 Specifi cation CPU: Intel Mobile Ivy Bridge processor in rPGA988B package Chipset: Intel Panther Point Platform Controller Hub (PCH) QM77 Memory: 1 x DDR3 SO-DIMM socket (up to 8GB), data transfer rates of 1333 MT/s and 1600 MT/s Graphics: Integrated with Intel Mobile Ivy Bridge Processor SIO and UARTs: Fintek F71869A and F81216AD I/O chipset On board SATA SSD 2/4/8/16/32/64 GB (Option) SATA: 2 x SATA ports (1 x SATA 2.0 and 1 x SATA 3.0)
  • Page 12: Installing The Cpu/Pch Heatsink. (Socket Version)

    1-3 Installing the CPU / PCH Heatsink. (Socket Version) 1. Remove the white wax paper from the 2. Install CPU bracket under the CPU fi rst. double-sided-adhesive-tap of the CPU Barcket 3.1. Locate Pin1 in the socket,look for a 3.2. Use screw driver and screw the socket golden narrow.
  • Page 13 3.3. Lock the CPU socket by securing the 4. Peel-off the Elastic Silicone sticker under the Heat Sink. screw in an anti-clockwise direction. 4.1. Tighten the HEAT SINK on the 4.2. Insert the system fan power cable to motherboard. Pay attention to tighten the the pin header (FAN1) on board.
  • Page 14: Vertical So-Dimm Assembly Guide

    1-4 Vertical SO-DIMM assembly guide 1. Install the memory into SODIMM. 2. Press down fi rmly to ensure the memory is locked. ------------------------------------------------------------------------------------------------------------------------ Uninstall 1. Pull open both sides of the memory slot. 2. Take out the memory.
  • Page 15: Installing The Mini Pci-E Card

    1-5 Installing the Mini PCI-e Card 2. Install a mSATA card at the angle of 45°. 1. Unfasten the round-headed M2*6 (The half size Mini PCI-e slot supports mSATA) screw for half size Mini PCI-e. 3. Fasten a round-headed M2*6 screw.
  • Page 16: Directions For Installing The Mini Card

    1-6 Directions for installing the Mini Card 1. Unscrew the screw on the board 2. Plug in the Mini Card in a 45 angle 3. Gently push down the Mini Card and screw the screw back.
  • Page 17: Packing List

    Material Code Description Detail Specifi cation Quantit 7G1901-1510001-0 MB-3I770CW-6CXX-00-001 LF,3I770CW-6CXX-00,Rev.:001 7G1901-1520001-0 MB-3I770A-6CXX-00-001 LF,3I770A-6CXX-00,Rev.:001 6G8006-2347-0100 LEX Product Driver DVD LF, Intel Baytrail Driver 6G8001-2193-0400 Manual LF,M/B,3I770A/CW 6G6003-7350-0100 Power Cable LF, 2.0 2*4/DC JK,L=9cm 6G5212-0601-0200 84W Power Adapter,12V/5A,2.5 LF,L Type,FSP060-DBAE1,FSP *The packing list above is for the users who purchase single motherboard. The users who purchase the board with chassis may refer to the packing list in the Assembly Guide.
  • Page 18: Chapter 2 Hardware Installation

    Chapter-2 Hardware Installation 2-1 Unpacking Precaution This chapter provides the information how to install the hardware of 3I770A/CW. Please follow section 1-7, 2-1 and 2-2 to check the delivery package and unpack carefully. Please follow the jumper setting procedure. NOTE! 1.
  • Page 19: Unpacking Checkup

    2-2 Unpacking checkup First of all, please follow all necessary steps of section 2-1 to protect 3I770A/CW from electricity discharge. With reference to section 1-7 please check the delivery package again with following steps: 1. Unpack the 3I770A/CW board and keep all packing material, manual and driver disc etc, do not dispose ! 2.
  • Page 20: Dimension-3I770A/Cw

    2-3 Dimension-3I770A/CW...
  • Page 21: Layout-3I770A/Cw

    2-4 Layout-3I770A/CW COH1 CPI1 COS1 CPI11 LED1 SODIMM1 JVC1 FAN1 CPP1 CPO2 HDMI1 JVL1 BAT1 CFP1 LVDS1 CIO2 CIO1 CKM1 CU12 CPO1 JSB1 CAL1 SIM1 CAR1 MPCE1 MPCE2 JSC3 JSB2 JVC3...
  • Page 22: Diagram-3I770A

    2-5 Diagram- 3I770A CPI1 LED1 SODIMM1 JVC1 FAN1 CPP1 JVL1 HDMI1 BAT1 CFP1 LVDS1 CIO2 CIO1 CKM1 CU12 CPO1 SIM1 CAL1 JSB1 CAR1 MPCE1 JSC3 MPCE2 JSB2 JVC3...
  • Page 23: Diagram-3I770Cw

    2-5-1 Diagram- 3I770CW CPI1 LED1 SODIMM1 JVC1 FAN1 CPP1 JVL1 HDMI1 BAT1 CFP1 LVDS1 CIO2 CIO1 CKM1 CU12 CPO1 SIM1 CAL1 JSB1 CAR1 MPCE1 JSC3 MPCE2 JSB2 JVC3...
  • Page 24: Bottom Side Diagram-3I770A/Cw

    2-5-2 Bottom Side Diagram- 3I770A/CW ottom Side Diagram- 3I770A/CW SATA1 SATA2 BACK Panel-3I770A/CW LAN2 LAN1 HDMI...
  • Page 25: Install Memory

    2-6 Install Memory This motherboard provides one 204-pin Small Outline Dual In-line Memory Module (SODIMM) socket for memory expansion available maximum to of 2GB/4GB/8GB DDR3 SDRAM. DDR3 clock supports: DDR3 1333/1600MT/S Valid Memory Confi gurations Total Memory DIMM1 System Accept or Not Max.
  • Page 26: List Of Jumpers

    2-7 List of Jumpers JSB1: CMOS clear select JSB2 : ME RTC clear select JSC3 : COM3 RS232/RS422/RS485 select JVC1 : COM1 voltage select JVC3 : COM3 voltage select JVL1 : LCD Panel power select 2-8 Jumper Setting Description A jumper is ON as a closed circuit with a plastic cap covering two pins. A jumper is OFF as an open circuit without the plastic cap.
  • Page 27: Coms Data Clear

    2-9 JSB1: CMOS DATA SET A battery must be used to retain the motherboard confi guration in CMOS RAM. Close Pin1 and pin 2 of JSB1 to store the CMOS data. To clear the CMOS,follow the procedures below: 1. Turn off the system and unplug teh AC power 2.
  • Page 28: Jsb2: Me Rtc Data Clear

    2-10 JSB2: ME RTC DATA Clear A battery must be used to retain the motherboard confi guration in ME RAM. Close Pin1 and pin 2 of JSB2 to store the ME data. To clear the ME,follow the procedures below: 1. Turn off the system and unplug teh AC power 2.
  • Page 29: Jsc3: Com3 Rs232/Rs422/Rs485 Select

    2-11 JSC3: COM3 RS232/RS422/RS485 select JSC3 RS232 *RS422 RS485 Short Short Open Open Short Open Note: RS232/RS422/485 setting by both H/W jumper and BIOS setting JSC3 RS232 *RS422 RS485 2-12 COM port pin9 select RI signal or Voltage source JVC1: COM1 PIN9 select JVC3: COM3 PIN9 select JVC1/3 Description...
  • Page 30: Jvl1: Lcd Panel Power Select

    2-13 JVL1: LCD panel power select JVL1 Description +3.3V *2-3 Note: Attention ! Check Device Power in spec JVL1 *+3.3V...
  • Page 31: Chapter 3 Connection

    Chapter-3 Connection This chapter provides all necessary information of the peripheral's connections, switches and indicators. Always power off the board before you install the peripherals. 3-1 List of Connectors CPI1: DC-in 2x4 pin (2.0mm) Red wafer connector CPI11: DC-in 1x4 pin (2.0mm) Red wafer connector ( Option ) BAT1: Li 3V battery holder CPO1: DC +5/+12V output 1x4 pin(2.0mm) Black wafer connector CPO2: DC +12V output 1x2 pin(2.0mm) Black wafer connector ( Option )
  • Page 32: Dc Power Input

    3-2 DC power input CPI1: DC-IN Internal Connector (2 X 4 pin 2.0mm Red Wafer) PIN NO. Description PIN NO. Description DC-IN DC-IN DC-IN DC-IN Note: 1. DC in from adapter plug in 2. Share CPI11 Connector 3. Mating connector: JST B8B-PHDSS or compatible 4.
  • Page 33: Battery Input

    3-3 Battery Input BAT1: 3V Battery hold 2pin BAT1: Battery use Li 3V / 220mAh (CR2032) Note: 1. When board without Adaptor plug in, this board power RTC consumption about 2.7uA 2. If adaptor always plug in RTC power consumption about 0.1uA BAT1 3-4 DC Power output CPO1: +12V/+5V DC voltage output (4pin 2.00mm Black Wafer)
  • Page 34: Front Panel & Fan

    3-5 Front panel & FAN CFP1 Front panel connector (2 X 5 pin 2.0mm wafer) PIN NO. Description PIN NO. Description Power button GND Power button pin Reset GND Reset pin Power LED - Power LED + HDD LED- HDD LED+ LAN LED- LAN LED+ *Note: 1.
  • Page 35: Display & Touch Interface

    3-6 Display & Touch interface CG1: VGA DB15 Connector PIN NO. Description PIN NO. Description GREEN BLUE DDC DATA H-SYNC V-SYNC DDC CLOCK HDMI1: HDMI Connector (Type A) PIN NO. Description PIN NO. Description TMDS DATA2+ TMDS DATA2- TMDS DATA1+ TMDS DATA1- TMDS DATA0+ TMDS DATA0-...
  • Page 36 LVDS1: LVDS interface (2 X 15 pin 1.25mm wafer) PIN NO. Description PIN NO. Description PWM dimming +LCD(5V or 3.3V) +LCD(5V or 3.3V) Channel-1-DATA3+ Channel-0-DATA3+ Channel-1-DATA3- Channel-0-DATA3- Channel-0-DATA2+ Channel-0-CLK+ Channel-0-DATA2- Channel-0-CLK- Channel-0-DATA1+ Channel-0-DATA0+ Channel-0-DATA1- Channel-0-DATA0- +LCD(5V or 3.3V) +LCD(5V or 3.3V) Channel-1-DATA2+ Channel-1-CLK+ Channel-1-DATA2-...
  • Page 37 CPP1: Panel Inverter power (5pin 2.0mm wafer) CPP1 PIN NO. Description +12V pin1 PWM dimming ENBKL (3.3V) ENBKL ( 5V ) Note: 1. JVP1 Inverter Voltage select 2. CPP1 PIN 3 and LVDS1 PIN1 is same signal. Default active setup by DPC Control 3.
  • Page 38: Audio Interface

    For 5- wire type pin defi ne PIN NO. Description PIN NO. Description UR(H) Sense UL(Y) LR(X) LL(L) Note: 1. Touch controller use USB port 8 2. Mating connector: JST B10B-PHDSS or compatible 3. Cable housing: JST PHDR-10VS or compatible 3-7 Audio interface CA3: Line-out/Line-in/Mic-in (2 X 4 pin 2.0mm wafer) PIN NO.
  • Page 39: I/O Interface

    3-8 I/O Interface COM ports (COM1~COM6 from super I/O) COM1/2/4/5/6 default support RS232 mode COM3 default support RS232/RS422/RS485 mode RS232 mode ports (D-SUB 9pin) CC1: COM1 PIN NO. Description PIN NO. Description RI/ Voltage Note: 1. The Pin 9 Voltage set by JVC1 for CC1 RS485 mode ports (D-SUB 9pin) CC1: COM1 PIN NO.
  • Page 40 RS232 mode ports (2 X 5 pin 2.0mm wafer) CC2: COM2 CC3: COM3 CC4: COM4 CC5: COM5 CC6: COM6 PIN NO. Description PIN NO. Description RI/ Voltage pin1 Note: 1. The Pin 9 Voltage set by JVC3 for CC3 2. Mating connector: JST B10B-PHDSS or compatible 3.
  • Page 41: Digital Input / Output

    3-9 Digital Input / Output CIO1 DIO 0 ~ 3 (2x5pin 2.0mm wafer) PIN NO. Description PIN NO. Description DI-0 DO-3 DI-1 DO-2 DI-2 DO-1 DI-3 DO-0 Note: 1. DI pin default pull up 10KΩ to +5V 2. If use need isolate circuit to control external device 3.
  • Page 42 For F75111N I C watch dog timer device: DC spec: Input low Voltage (VIL)\+0.8 Max Input High Voltage (VIH): +2V Min Output low Current (IOL): 10mA (Min) VOL=0.4V Output High Current (IOH): -10mA (Min) VOH=2.4V Watch Dog Time value 0~255 sec The system will be issued reset.
  • Page 43: I C Bus Interface

    3-10 I C Bus Interface CO1: I C (SM) bus connector (4 pin 1.25mm wafer) PIN NO. Description +3.3V SMB_CLK SMB_DATA Note: 1. Mating connector: MOLEX 53047-0410 or compatible 2. Cable housing: MOLEX 51021-0400 or compatible pin1 3-11 PS2 KB/MS CKM1: KB/MS port (1 X 6 pin 1.25mm wafer) PIN NO.
  • Page 44: Lan Interface

    3-12 LAN Interface CL1 / CL2: LAN Giga/100Mb (RJ45 Jack) PIN NO. Description PIN NO. Description TD0-/TX+ TD2-/NC TD0+/TX- TD2+/RX- TD1-/RX+ TD3-/NC TD1+/NC TD3+/NC RJ45 LAN Connector--- LED defi ne Giga/100MB Connector Back side con RED LED GREEN LED YELLOW LED GIGA LAN 100Mb LAN Active LED...
  • Page 45: Usb Interface

    3-13 USB Interface CU5/CU6: USB4/5 ports (USB Type A connector) PIN NO. Description USB DATA - USB DATA + Note: 1. Attention ! Check Device Power in spec CU3/CU4/CU7/CU8/CU9: USB 2/3/11/12/13 ports PIN NO. Description USB DATA - USB DATA + Note: 1.
  • Page 46: Sata Interface

    3-14 SATA interface SATA1/SATA2: The two SATA connectors PIN NO. Description DATA TX+ DATA TX- DATA RX- DATA RX+ Note: 1. SATA1 support SATA 3.0 spec update 6Gb/sec . 2. SATA2 support SATA 2.0 spec update 3Gb/sec . 3. CPO1 provide SATA HDD power +12V, GND, +5V SATA1 SATA2 SSD use at SATA3 channel...
  • Page 47: Module Socket

    3-15 Module socket Mini card MPCE1/MPCE2: Support USB and PCIe by one Interface (Mini card socket 52pin) PIN NO. Description PIN NO. Description +3.3V +1.5V SIM Power SIM Data PCIe-CLK- SIM CLK PCIe-CLK+ SIM Reset SIM RFU RST- PCIe-RX-/mSATA-RX+ +3.3V PCIe-RX+/mSATA-RX- +1.5V SMB-CLK...
  • Page 48: Sim Socket

    3-16 SIM Socket SIM1: SIM card socket pin defi ne is follow ISO 7816-2 smart card standard. PIN NO. Description PIN NO. Description DATA Note: 1. MPCE1 Pin 8, 10,12,14,16 for SIM1 card reader use. 3-17 SODIMM socket Note: 1.SODIM1: SO-DIM DDR3 1.5V DRAM Socket 2.
  • Page 49: Introduction Of Bios

    Chapter-4 Introduction of BIOS The BIOS is a program located in the Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gains control. The BIOS fi rst operates an auto-diagnostic test called POST (Power on Self Test) for all the necessary hardware, it detects the entire hardware devices and confi...
  • Page 50: Bios Menu Screen

    The following diagram show a general BIOS menu screen Main Advanced Save & Exit Chipset Boot Security Menu Bar Set the date. Use Tab BIOS Vendor 3I770A-C A1 to Switch between Processor Information date elements. Name IvyBridge Brand String Intel(R) Core(TM) i7 Frequency 2300 MHz...
  • Page 51: Getting Help

    The selected one is highlighted. 4-6 Main Main Advanced Save & Exit Chipset Security Boot Set the date. Use Tab BIOS Vendor 3I770A-C to Switch between Processor Information date elements. Name IvyBridge Brand String Intel(R) Core(TM) i7 Frequency 2300 MHz →←: Select Screen...
  • Page 52: Advanced

    4-7 Advanced Main Advanced Save & Exit Chipset Boot Security System ACPI ►ACPI Settings Parameters. ►S5 RTC Wake Setting ►Trusted Computing ►CPU Confi guration ►SATA Confi guration →←: Select Screen ►SMART Setting ↑↓: Select Item ►F71869 Super IO Confi guration Enter: Select ►F71869 H/W Monitor +/-: Change Opt.
  • Page 53: Acpi Settungs

    4-7-1 ACPI Settings Main Advanced Save & Exit Chipset Boot Security Enables or Disables ACPI Settings BIOS ACPI Auto Confi guration. Enable ACPI AUTO Confi guration [Disabled] Enable Hibernation [Enabled] →←: Select Screen ACPI Sleep State [S1 only(CPU Stop C..)] ↑↓: Select Item Enter: Select +/-: Change Opt.
  • Page 54: S5 Rtc Wake Settings

    4-7-2 S5 RTC Wake Settings Main Advanced Save & Exit Chipset Security Boot Enable or disable Wake system with Fixed Time [Disabled] System wake on alarm event when enabled. System will wake on the hr : min : sec specifi ed →←: Select Screen ↑↓: Select Item Enter: Select...
  • Page 55: Cpu Configuration

    4-7-4 CPU Confi guration Main Advanced Chipset Save & Exit Boot Security Enabled for Windows CPU Confi guration XP and Linux (OS optimized for Hyper- Intel(R) Core(TM) i7-3610QE CPU @ 2.30GHz threading Technology) CPU Signature 306a9 and Disabled for other Microcode Path OS (OS not optimized for Hyper-threading...
  • Page 56: Sata Configuration

    4-7-5 SATA Confi guration Main Advanced Save & Exit Chipset Security Boot Enable or disable SATA SATA Controller(s) [Enabled] Device. SATA Mode Selection [IDE] →←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save &...
  • Page 57: Software Feature Mask Configuration

    4-7-5-1-1 ►Software Feature Mask Confi guration Main Advanced Chipset Save & Exit Boot Security Enable or disable RAID0 RAID0 [Enabled] feature. RAID1 [Enabled] →←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save &...
  • Page 58: Smart Settings

    4-7-6 SMART Settings Main Advanced Save & Exit Chipset Security Boot Run SMART Self Test on Smart Settings all HDDs during POST. Smart Self Test [Disabled] →←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save &...
  • Page 59: Serial Port 1 Configuration & Serial Port 2 Configuration

    4-7-7-1 ►Serial Port 1 Confi guration & Serial Port 2 Confi guration Main Advanced Save & Exit Chipset Boot Security Enable or Disable Serial Serial Port 1~2 Confi guration Port (COM) Serial Port [Enabled] →←: Select Screen Device Settings IO=3F8h; IRQ=4; ↑↓: Select Item Enter: Select Change Settings...
  • Page 60: F81216 Second Super Io Configuration

    4-7-9 F81216 Second Super IO Confi guration Main Advanced Save & Exit Chipset Boot Security Set Parameters of Serial F81216 Second Super IO Confi guration Port 3(COMC) F81216 Second Super IO Chip F81216 SecondIO →←: Select Screen ►Serial Port 3 Confi guration ↑↓: Select Item ►Serial Port 4 Confi...
  • Page 61: Serial Port Console Redirection

    Serial Port Use this item to enable or disable serial port (COM). The optional settings are: Enabled, Disabled. Change Settings Use this item to select an optimal setting for super IO device. The optional settings are: AUTO IO=260h; IRQ=11; IO=260h; IRQ=10,11,12; IO=268h;...
  • Page 62: Network Stack

    4-7-11 Network Stack Main Advanced Chipset Security Save & Exit Boot Enable/Disable UEFI Network stack [Disabled Link] network stack. →←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit Esc: Exit Version 2.14.1219.
  • Page 63: Pch-Io Configuration

    4-8-1 ►PCH-IO Confi guration Main Advanced Chipset Security Save & Exit Boot PCI Express Intel PCH SKU Name QM77 Confi guration settings Intel PCH Rev ID 04/C1 →←: Select Screen ►PCI Express Confi guration ↑↓: Select Item ►USB Confi guration Enter: Select ►PCH Azalia Confi...
  • Page 64: Mini Pcie 1/2

    4-8-1-1-1 ►Mini PCIe 1/2 Main Advanced Chipset Save & Exit Boot Security PCI Express Root Port 3 PCI Express Root Port 3/4 [Enabled] Setting. PCIe Speed [Gen1] →←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save &...
  • Page 65: Pch Azalia Confuguration

    HS Port #1 Switchable HS Port #2 Switchable HS Port #3 Switchable HS Port #4 Switchable Always for HS port switching between xHCI and EHCI. If disabled, port is routed to EHCI. If HS port is routed to xHCI, the corresponding SS port is enabled. The optional settings are: Disabled, Enabled.
  • Page 66: System Agent(Sa) Confuguration

    4-8-2 ►System Agent (SA) Confi guration Main Advanced Save & Exit Chipset Security Boot Confi g Graphics System Agent Bridge Name IvyBridge Settings. System Agent RC Version 1.2.0.0 →←: Select Screen ►Graphics Confi guration ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults...
  • Page 67: Lcd Control

    LCD Control Please refer section 4-8-2-1-1 4-8-2-1-1 LCD Control Main Advanced Save & Exit Chipset Boot Security Select the Video Graphics Confi guration Device which will be activated during POST. Primary IGFX Boot Display [CRT] This has no effect Secondary IGFX Boot Display [HDMI] if external graphics LCD Panel Type...
  • Page 68: Boot

    LCD Panel Type This item allows you to select the panel resolution VBIOS Default 1024 X 600 LVDS 800 X 600 LVDS 1024 X 768 LVDS1 1280 X 1024 LVDS 1440 X 1050 (RB) LVDS1 1440 X 1050 LVDS2 1600 X 1200 LVDS 1366 X 768 LVDS...
  • Page 69: Csm Parameters

    Quiet Boot The optional settings are: Enabled, Disabled. Gate A20 Active UPON REQUEST- GA20 can be disabled using BIOS services. ALWAYS- do not allow disabling GA20. CSM parameters Please refer section 4-9-1 4-9-1 CSM parameters Main Advanced Save & Exit Chipset Boot Security...
  • Page 70: Security

    4-10 Security Main Advanced Chipset Security Save & Exit Boot Set Administrator Password Description Password If ONLY the Administrator’s password is set, Then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to Boot or enter Setup.
  • Page 71: Save & Exit

    4-11 Save & Exit Main Advanced Save & Exit Chipset Security Boot Reset the system after Save Changes and Reset saving the changes. Restore Defaults Boot Override →←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save &...
  • Page 72: Chapter 5 Driver Installation

    Chapter-5 DRIVER INSTALLATION There is a system installation DVD in the package. This DVD does not only include all the drivers you need but also some other free application programs and utility programs. In addition, this DVD also includes an auto detect software telling you which hardware is installed and which driver is needed so that your system can function properly.
  • Page 73 AUTOMATIC DRIVER INSTALLATION menu 1. INF install Intel Ivy Bridge chipset driver 2. VGA install Intel onboard VGA driver 3. SOUND install HD Audio Codec driver 4. LAN to the LAN driver Readme fi le 5. COM to the COM driver Readme fi le 6.
  • Page 74: Inf Install Intel Baytrail Chipset Driver

    5-1 INF Install Intel Baytrail Chipset Driver 1. At the "AUTOMATIC DRIVER INSTALLATION 2. At the "Intel® Chipset Device Software" menu" screen, click "INF". screen, click "Next". 3. At the "License Agreement" screen, 4. At the "Readme File Information" screen, click "Yes"...
  • Page 75 6. Click "Finish" to restart computer 5. Click "Next" NOTE: SYSTEM INSTALL will auto detect fi le path For Windows XP 64/32-bit, Windows 7 64/32-bit and windows 8 64/32-bit X:\driver\INTEL\IVY_SAN\inf\infi nst_autol.exe For Windows 8.1 64/32-bit X:\driver\INTEL\IVY_SAN\inf\WIN8.1\Setup.exe...
  • Page 76: Vga Install Intel Lvy Bridge Vga Driver

    5-2 VGA Install Intel Ivy Bridge VGA Driver 1. At the"AUTOMATIC DRIVER INSTALLATION 2. At the "Intel® HD Graphics Driver" screen, menu"screen, click "VGA". Click "Next". 3. At the "Welcome to the Setup Program" 4. At the "License Agreement" screen, screen, Click "Next".
  • Page 77 6. At the "Setup Progress" screen, 5. At the "Readme File Information" screen, Click "Next". Click "Next". 7. Click “Finish” to restart computer NOTE: SYSTEM INSTALL will auto detect fi le path For Windows XP 64bit X:\driver\INTEL\IVY_SAN\vga\winxp64\winxp64_145110.exe For Windows XP 32bit X:\driver\INTEL\IVY_SAN\vga\winxp\winxp_145110.exe For Windows 7 64bit and Windows 8 64bit X:\driver\INTEL\IVY_SAN\vga\ WIN_7_8_64\ win64_152812.exe...
  • Page 78: Sound Install Realtek High Definition Audio Driver

    5-3 SOUND Install Realtek High Defi nition Audio Driver 1. At the "AUTOMATIC DRIVER INSTALLATION 2. Click "Next". menu" screen, click "SOUND". 3. Click "Finish" to restart computer NOTE: SYSTEM INSTALL will auto detect fi le path For Windows XP 32/64 bit X:\driver\INTEL\IVY_SAN\SOUND\WDM_R270.exe For Windows 7 32/64 bit and Windows 8 32/64 bit X:\driver\INTEL\IVY_SAN\SOUND\Vista_Win7_Win8_R270.exe...
  • Page 79: Usb 3.0 Install Intel Usb 3.0 Extensible Host Controller Driver

    5-4 USB 3.0 Install Intel USB 3.0 extensible Host Controller Driver 1. At the "AUTOMATIC DRIVER 2. At the "Intel® USB 3.0 extensible Host INSTALLATIONmenu" screen, Click "USB 3.0 Controller Driver" screen, Click" Next. 3. At the "License Agreement" screen, 4.
  • Page 80 6. Click "Finish" to restart computer 5. Click "Next". NOTE: The path of the fi le For Windows 7 32/64-bit X:\driver\INTEL\IVY_SAN\USB3_0\INTEL\Setup.exe...
  • Page 81: Me Install Intel Management Engine Intergace Driver

    5-5 ME Install Intel Management Engine Interface Driver 1. Plaese Check Device Manager "PCI 2. At the "Intel® Management Engine Simple Communications Controllers" Components"screen, Click" Next. 3. At the "Setup Progress" screen, 4. Click "Next". Click "Next".
  • Page 82 5. Click "Finish" 6. Plaese Check Device Manager "PCI Simple Communications Controllers" NOTE: The path of the fi le For Windows XP 32/64 bit and Windows 7 32/64-bit X:\driver\INTEL\ME TOOL\MEI-Only Installer\MEISetup.exe...
  • Page 83: How To Update Insyde Bios

    5-6 How to update Insyde BIOS Step 1. To run afuwingui.exe then click "Open" Step 2. Click the new version BIOS (download from the website)
  • Page 84 Step 3. Choose "ProgramAll Blocks" and "Do Not Check ROM ID" Step 4. Click "Flash" Step 5. Click "Exit" and restart computer.
  • Page 85: Appendix A:power Consumption Test

    Appendix A: Power Consumption Test Condition Item Spec intel core i7, i5, i3, Celeron 1020E Memory DDR3 1600 4GB Operating System Windows 7 / SP1 Test Program 3D Mark Vantage HDD 2.5" SATA Slim Type HDD mSATA 32GB Test Result for reference only ! Start up Operation Shut down...
  • Page 86: Appendix B:resolution List

    Appendix B: Resolution list 640 x 480 x ( 256 / 16bit / 32bit ) 800 x 600 x ( 256 / 16bit / 32bit ) 1024 x 768 x ( 256 / 16bit / 32bit ) 1152 x 864 x ( 256 / 16bit / 32bit ) 1280 x 600 x ( 256 / 16bit / 32bit ) 1280 x 720 x ( 256 / 16bit / 32bit ) 1280 x 768 x ( 256 / 16bit / 32bit )
  • Page 87: Appendix C: F75111N I C Dio Decice

    Appendix C: F75111N I C DIO device 1-1 IO Device: F75111 under Windows The Sample code source you can download from Source fi le: F75111_DIOSrc.rar http://tprd.info/lexwiki/index.php/IO_Device:F75111 Binary fi le: F75111_DemoBin.rar USERNAME & PASSWORD: sf How to use this Demo Application 1.
  • Page 88 p.s. f75111 send "F75111_SetWDTEnable(BYTE byteTimer)" including a parameter "timer", if there's no disable signal (F75111_SetWDTDisable()) to stop it before timer countdown to 0, System will reboot. if there's disable signal received, resent Enable WDT signal, for a loop to prevent from reboot Introduction Initial Internal F75111 port address (0x9c) defi...
  • Page 89 Set output value void F75111::InterDigitalOutput(BYTE byteValue) BYTE byteData = 0; byteData = (byteData & 0x01 )? byteValue + 0x01 : byteValue; byteData = (byteData & 0x02 )? byteValue + 0x02 : byteValue; byteData = (byteData & 0x04 )? byteValue + 0x04 : byteValue; byteData = (byteData &...
  • Page 90: Io Device: F75111 Vb6 Under Windows

    Disable WatchDog void F75111_SetWDTDisable () WriteByte(F75111_INTERNAL_ADDR,WDT_CONFIGURATION,0x00); // Disable WatchDog 1-2 IO Device: F75111 VB6 under Windows The Sample code source you can download from Source fi le: 75111_VB_v10.rar http://tprd.info/lexwiki/index.php/IO_Device:F75111_VB6 Binary fi le: 75111_VB_Src.rar USERNAME & PASSWORD: sf How to use this Demo Application A Function - Enable WDT timer ,Key-in the value by seconds then system will reboot after value which you key-in in left text box !! B Function - Disable WDT timer ,Push down the button then WDT timer value will be clear !!
  • Page 91 SDK Function Introduction Function EnableWDT Function EnableWDT(timer As Integer) Call WriteI2CByte(&H3, &H3) Call WriteI2CByte(&H37, timer) Call WriteI2CByte(&H36, &H73) End Function Function DisableWDT Function DisableWDT() Call WriteI2CByte(&H36, &H0) End Function Function SetDOValue Function SetDOValue(dovalue As Integer) Call WriteI2CByte(&H23, &H0) Call WriteI2CByte(&H20, &HFF) Call WriteI2CByte(&H2B, &HFF) Call WriteI2CByte(&H21, dovalue) End Function...
  • Page 92: Io Device: F75111 Under Linux

    1-3 IO Device: F75111 under linux The Sample code source you can download from Source fi le: F75111v2.0L.tar.gz http://tprd.info/lexwiki/index.php/IO_Device:F75111_under_linux Binary fi le: F75111v2.0LBin.tar.gz USERNAME & PASSWORD: sf How to compile source code 1. Compile source code with Code::Blocks download and install the Code::Block with command "apt-get install codeblocks" Open an exist project(F75111.cbp) in Code::Blocks, click the compile button ( add an option 'pkg-confi...
  • Page 93 1. Press the "Start" button to test DIO function 2. Press the "Enable" button to test WDT function 3. Press the "Disable" button to disable WDT 4. Check the "Enable Loop" box and press "Enable" to do WDT loop test 5.
  • Page 94 Set output value void F75111::InterDigitalOutput(BYTE byteValue) BYTE byteData = 0; byteData = (byteData & 0x01 )? byteValue + 0x01 : byteValue; byteData = (byteData & 0x02 )? byteValue + 0x02 : byteValue; byteData = (byteData & 0x04 )? byteValue + 0x04 : byteValue; byteData = (byteData &...
  • Page 95 Enable WatchDog void F75111_SetWDTEnable (BYTE byteTimer) WriteByte(F75111_INTERNAL_ADDR,WDT_TIMER_RANGE ,byteTimer); // set WatchDog range and timer WriteByte(F75111_INTERNAL_ADDR,WDT_CONFIGURATION,WDT_TIMEOUT_FLAG | WDT_ENABLE | WDT_PULSE | WDT_PSWIDTH_100MS); // Enable WatchDog, Setting WatchDog confi gure Disable WatchDog void F75111_SetWDTDisable () WriteByte(F75111_INTERNAL_ADDR,WDT_CONFIGURATION,0x00); // Disable WatchDog...

This manual is also suitable for:

3i770cw

Table of Contents