Jonsered FC2245 Operator's Manual
  1. Manuals
  2. Brands
  3. Jonsered Manuals
  4. Trimmer
  5. FC2245
  6. Operator's manual

Jonsered FC2245 Operator's Manual

Hide thumbs Also See for FC2245:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual
FC2245, FC2245W, CC2245
EN
Operator's manual
2-31

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FC2245 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Jonsered FC2245

Summary of Contents for Jonsered FC2245

  • Page 1 FC2245, FC2245W, CC2245 Operator's manual 2-31...

  • Page 2: Table Of Contents

    Contents Introduction..............2 Transportation, storage and disposal......27 Safety................4 Technical data.............. 27 Assembly..............10 Accessories..............29 Operation..............14 EC Declaration of Conformity........31 Maintenance..............21 ..................0 Troubleshooting............26 Introduction Product description use the product for other tasks than grass trimming, grass clearing and forestry clearing.
  • Page 3 Product overview FC 2245 CC 2245 1. Saw blade 20. Support flange 2. Grease fill cap, bevel gear 21. Drive disc 3. Bevel gear 22. Trimmer head 4. Cutting attachment guard 23. Spark plug cap and spark plug 5. Shaft 24.

  • Page 4: Safety

    Read the operator's manual carefully and make sure that you understand the Fuel. instructions before use. Use a protective helmet in locations where objects can fall on you. Use approved Decompression valve. hearing protection. Use approved eye protection. Maximum speed of the output shaft. Heated handles.
  • Page 5 General safety instructions Safety instructions for operation WARNING: Read, understand and obey these instructions carefully before you use WARNING: Read the warning instructions the product. that follow before you use the product. • Learn and understand the difference between WARNING: This product produces an forestry clearing, grass clearing and grass trimming electromagnetic field during operation.

  • Page 6: Personal Protective Equipment

    Personal protective equipment such as roots, rocks, branch and ditches. Be careful during work on slopes. WARNING: Read the warning instructions that follow before you use the product. • Always use approved personal protective equipment when you use the product. Personal protective equipment cannot fully prevent injury but it decreases the degree of injury if an accident does occur.
  • Page 7 5. Press the throttle trigger (B) and make sure that it devices regularly. If the safety devices are defective, goes back to its initial position when you release it. speak to your JONSERED service agent. • Do not make changes to safety devices. Do not use...
  • Page 8 To do a check of the stop switch 3. Make sure you attach the elements of the vibration damping system are correctly. 1. Start the engine. 2. Move the stop switch to the stop position and make sure that the engine stops. To do a check of the cutting attachment guard The cutting attachment guard stops objects that ejects in the direction of the operator.
  • Page 9 To do a check of the locknut WARNING: The mufflers become very hot during and after operation, also at idle WARNING: Stop the engine, use protective speed. Use protective gloves to prevent gloves and be careful around the sharp burn injuries. edges of the cutting attachment.

  • Page 10: Assembly

    Move the product at a minimum of 3 m (10 ft) from agent do all other servicing. the position where you filled the tank before a start. • Let an approved JONSERED service agent do • Do not put too much fuel in the fuel tank. servicing on the product regularly.
  • Page 11 To set the handlebar in transport 2. Put the throttle handle onto the right side of the handlebar. position 1. Loosen the knob. 2. Turn the handlebar clockwise until the throttle handle touches the battery. 3. Turn the handlebar around the shaft. 3.
  • Page 12 1. Put the blade guard/combination guard (A) onto the shaft and tighten the bolt to attach it. 2. Make sure that the guard extension is removed. To attach the saw blade guard (FC2245, 3. Turn the output shaft to align one of the holes in the FC2245W) drive disc (B) with the related hole in the gear housing.
  • Page 13 To attach the saw blade (CC2245) 3. Put the locking pin (C) in the groove on the bolt head and tighten the bolt fully. 1. Put the drive disc (A) on the output shaft. 2. Turn the output shaft to align one of the holes in the drive disc with the related hole in the gear housing.

  • Page 14: Operation

    4. Attach the strap (A) in correct position for grass 9. Tighten the elastic strap (B) to move more load from clearing or forestry clearing. the shoulder strap to the hip strap. 5. Tighten the hip strap tightly. Make sure that the hip 10.
  • Page 15 • For best results and performance use JONSERED two-stroke oil. • If JONSERED two-stroke oil is not available, use a two-stroke oil of good quality for air-cooled engines. Speak to your servicing dealer to select the correct oil. CAUTION: Do not use two-stroke oil for •...

  • Page 16: To Start A Cold Engine

    • Keep body parts away from the hot surfaces. CAUTION: Small errors can influence the • Keep body parts away from the cutting attachment. ratio of the mixture drastically when you mix small quantities of fuel. Measure the quantity Correct balance of the product of oil carefully and make sure that you get the correct mixture.
  • Page 17 4. Hold the body of the product on the ground with your 6. Pull the starter rope handle quickly and with force. left hand. Pull the starter rope handle until the engine starts. To stop the engine • Move the stop switch to the stop position. CC 2245 FC 2245 CAUTION: Do not step on the product.
  • Page 18 General work instructions 3. Tilt the saw blade and push it with force diagonally down to the right. At the same time, push the tree with the blade guard. WARNING: Be careful when you cut a tree that is in tension. It can spring back to its normal position before or after the cut and hit you or the product, and cause injury.
  • Page 19 3. Do the first cut on the side of the tree to which it will • For groups of thin trees: fall. 4. Cut through the tree from the other side. a) Cut the outer trees high up. b) Cut the outer trees to the correct height. c) Cut from the center.
  • Page 20 b) Do not move the grass blade through cut 7. Reduce the risk of material wrapping around the material when you move the product from left to blade by always work at full throttle and avoid the right. previously cut material during the return stoke. •...

  • Page 21: Maintenance

    Maintenance Introduction For all servicing and repair work on the product, special training is necessary. We guarantee the availability of professional repairs and servicing. If your dealer is not a WARNING: Before you do maintenance, you service agent, speak to them for information about the must read and understand the safety nearest service agent.
  • Page 22 Technical data on page 27 for the Note: Refer to recommended idle speed. Your JONSERED product is made to specifications that decrease harmful emissions. To adjust the start throttle speed 1. Make sure that the air filter is clean and the air filter (CC2245) cover is attached before you adjust the idle speed.

  • Page 23: Air Filter

    CAUTION: Do not bend of fold the air filter as this can cause damage to the air filter. Replace a damaged air filter. To clean a nylon air filter (FC2245, FC2245W) 1. Remove the air filter cover. Clean the cooling system weekly or more frequently if it is necessary.

  • Page 24: Drive Shaft

    The bevel gear is filled to ¾ with grease at the factory. Before use, make sure that the grease level has not changed. Use JONSERED special grease if it is necessary to fill up. Do not change the grease in the bevel gear.
  • Page 25 • Adjust the blade set to 1 mm with the recommended WARNING: Always discard a blade that is setting tool. Refer to the instructions that come with damaged. Do not try to make a bent or the blade. twisted blade straight and use it again. To sharpen the saw blade WARNING: Stop the engine.

  • Page 26: Troubleshooting

    • Attach the air duct as shown in the illustration. Make CAUTION: Do not operate the product at sure that the arrow points in the direction of the temperatures of more than than 5° if it is winter mode symbol. adjusted for winter mode.

  • Page 27: Transportation, Storage And Disposal

    • Attach the product during transportation. Make sure • Clean and do servicing on the product before long- that it cannot move. term storage. Technical data /2.0 Technical data FC2245 FC2245W CC2245 Engine Cylinder displacement, cm 45.7 45.7 45.7 Idle speed, rpm...
  • Page 28 FC2245 FC2245W CC2245 Max. engine power, according to ISO 8893, 2.2/3.0 @ 9000 2.2/3.0 @ 9000 2.1/2.8 @ 9000 kW/hp @ rpm Catalytic converter muffler Ignition system Spark plug NGK CMR6H NGK CMR6H NGK CMR6H Electrode gap, mm Fuel Fuel tank capacity, l/cm 0.9/900...

  • Page 29: Accessories

    Accessories Accessories (FC2245, FC2245W) Approved accessories Accessory type Cutting attachment guard, art. no. Centre hole in blades/knives, Ø 25.4 Output shaft thread M12 Grass blade/grass cutter Multi 255-3 (Ø 255, 3 teeth) 537 29 74-02 / 544 46 43-01 Multi 275-4 (Ø 275, 4 teeth) 537 29 74-02 / 544 46 43-01 Multi 300-3 (Ø...
  • Page 30 Approved accessories Accessory type Cutting attachment guard, art. no. Support cup Fixed With ball bearing 1145 - 001 - 09.04.2019...

  • Page 31: Ec Declaration Of Conformity

    FC2245W, SEC/11/2309 - CC2245. RISE SMP Svensk Maskinprovning AB has also verified agreement with appendix V of the council’s directive 2000/14/EG. The certificate has the number: 01/164/077 - FC2245, FC2245W, 01/164/076 - CC2245. Huskvarna March 30, 2016 Per Gustafsson, Development Manager (Authorized...
  • Page 32 Original instructions 1157545-26 2019-05-08...

This manual is also suitable for:

Fc2245wCc2245

Table of Contents