Maintenance; System Troubleshooting - Fora TN'G Scale 550 Operating Instructions Manual

Once a stable value is obtained, the reading will flash
three times and then calculate your BMI.
4. Understanding your displayed result.
1 2
5
Personal Profile Number
1
Gender: Male
2
Volume
3
Your Weight
4
5. Step off the weighing platform.
The result is saved in the scale memory and the scale enters into Bluetooth mode.
SCALE MEMORY
Your scale stores up to a 135 measurements for all 5 personal profiles. Results in
memory can be transmitted to the mobile device by wireless connection. This allows
you to review your measurements on your mobile device.
Bluetooth pairing and data transmission
Please make sure you have installed the software in your device (smart phone or
tablet) before pairing. Please note that you must pair your weight scale to your device
before transmitting data.
Pairing with your mobile device
1. Press and Hold SET for 5 seconds until the Bluetooth symbol is displayed and starts
to flash.
2. Make sure your mobile device is in Bluetooth mode, then launch the iFORA WS APP
on your device, go to the settings tab and press pair. Then press "search", the APP will
then start to search for your scale.
3. After successfully pairing the APP to your scale, the Bluetooth function on the scale
will then start to transmit your data to your APP.
Bluetooth indicator on the weight scale
BLUETOOTH INDICATOR
Flashing The Bluetooth function is enabled and waiting for
connection.
Solid The Bluetooth connection is established.
Data transmission
After each measurement, the Bluetooth function on the scale will activate and try to
connect to your paired device (e.g smart phone or tablet) to transmit data.
1 2 6
3 3
4 7
Weight Unit
5
BMI Symbol
6
Your BMI
7
STATUS
NOTE:
● While the weight scale is in transmission mode, it will be unable to perform a test.
● Make sure that your device supporting Bluetooth Smart Technology has turned on
Bluetooth before transmitting the data and the weight scale is within the receiving
range. For the requirement of OS version, please find on App Store or Google Play
when you download the app.
● A compatibility issue between your mobile device and the meter might occur due to
the way Bluetooth functionality is implemented by the various mobile device
manufacturers.

MAINTENANCE

Your scale uses four 1.5V AAA alkaline batteries.
Low Battery Signal
The scale will display the message shown to alert you
when the scale power is running low. This means it is
about time to replace the batteries.
WARNING!
If the incorrect type of battery is used, it may cause damage to the scale.
NOTE:
● Zero out - Press the SET button and quickly release to turn the scale on and wait for
the LCD to display 0.0. Please wait 2 seconds then start the measurement.
● Replacing the batteries does not affect the test results stored in memory.
● Properly dispose of the batteries according to your local environmental regulations.
● Batteries may leak chemicals if left unused for a long time. Remove the batteries if
you are not going to use the device for an extended period (i.e. 3 months or more).
Cleaning
● To clean the outside of the scale, wipe it with a slightly damped cloth and water or a
mild cleaning agent, and then dry the device with a soft dry cloth. Do NOT immerse
the device in water.
● Do NOT use chemical or organic solvents to clean the scale.
● Wipe the scale clean at once if any grease, sauce, vinegar, juice or other
substances that may cause damage are spilled on the scale.
Scale Storage
● Storage condition: -13°F to 158°F (-25°C to 70°C), below 93% relative humidity.
● Avoid dropping the scale or heavy impact.
● Avoid direct sunlight and high levels of humidity.

SYSTEM TROUBLESHOOTING

Error Messages
MESSAGE WHAT IT MEANS
The weighing subject exceeds
the maximum capacity of the
device.
If you follow the recommended action but the problem persists, or if error messages
other than the ones shown above appear, please contact local customer service. Do
not attempt to repair the device by yourself and do not try to disassemble the scale
under any circumstances.
Replacing the batteries
When replacing the batteries, make
sure that the scale is turned off.
1. Press the edge of the battery cover
and lift it up.
2. Remove the old batteries and replace
them with four 1.5V alkaline batteries.
3. Close the battery cover.
4. Zero out. (See NOTE)
WHAT TO DO
Remove the weighing subject
from the platform to avoid
damage.