Advertisement
A S S E M B LY I N S T R U C T I O N S
4x4 Lamp Post with EZ Mount
Please read through before starting assembly.
Check Box for These Contents
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346
(Mon. to Fri.8:00 AM to 4:00 PM EST) or UK Tel:(44) 2038 687160 - (Mon. to Fri. 1:00 PM to 10:00 PM GMT).
1. Lamp Post (1)
- 4" x 4" x 72" (10x10x183cm) - 10273
2. EZ Mount Anchor Assembly (1)
3. Post Cap (1)
- 10272
4. 5/8" (16mm) Self-Tapping Screw (1)
5. Tube of Vinyl Weld (1)
- 20000
Tools You Will Need
• Tape Measure
• Level
• Sledge Hammer
• Cordless Drill with #2 Phillips Bit
Purchased Separately
• Lamp Fixture
General Information
• Read Instructions through carefully before beginning assembly.
• When handling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 10'x 8' (3m x 2.4m) for unobstructed handling.
Important Note:
• Please refer to local codes before installing outdoor lighting. UF-rated cable should be used for underground
wiring and all materials should be approved by the Underwriter's Laborator (UL). New England Arbors
assumes no liability for errors, ommissionsm or the outcome of any project.
- 1 5/8" Diameter x 48" (4cm Diameter x 122cm) - 11102
- 20016
3 in (7.6 cm)
Diameter
73 7/8 in
(188 cm)
24 in
(61 cm)
24 in
(61 cm)
3
Not to Scale
www.newenglandarbors.com
www.newenglandarbors.co.uk
1
2
4
5
Ver 1.2-012218
1
Advertisement
Table of Contents
Related Manuals for New England Arbors VA94436
Summary of Contents for New England Arbors VA94436
-
Page 1: General Information
Important Note: • Please refer to local codes before installing outdoor lighting. UF-rated cable should be used for underground wiring and all materials should be approved by the Underwriter’s Laborator (UL). New England Arbors Ver 1.2-012218 assumes no liability for errors, ommissionsm or the outcome of any project. - Page 2 S T E P O N E EZ Mount Anchor Installation Temporarily remove top outer gear by pulling the two locking tabs away from the top inner gear. This will protect the top outer gear from possible damage when driving the EZ Mount anchor pipe into the ground. Drive the EZ Mount anchor pipe into the ground using a sledge hammer (10-pound / 4.5kg hammer is preffered;...
- Page 3 S T E P T W O EZ Mount Anchor Adjustment The top and bottom outer leveling gears on the anchor pipe are designed to be adjustable to compensate for a slightly crooked pipe. The position of the top and bottom outer gears can be unlocked and adjusted as needed, to provide a level surface for the vinyl lamp post.
- Page 4 S T E P T H R E E Lamp Post Installation Using a cordless drill with a #2 Phillips bit, fasten the lamp post Slide the lamp post over the pipe anchor assembly. to the bottom outer gear with the 5/8" (16 mm) self-tapping screw as shown.
- Page 5 S T E P F O U R Post Cap Installation www.newenglandarbors.com If you’re installing an electrical hardwired lamp fixture, www.newenglandarbors.co.uk thread the electrical cable through the post cap opening as shown Apply a bead of vinyl weld to the inside walls of the post cap and slide the post cap on to the lamp post.
Need help?
Do you have a question about the VA94436 and is the answer not in the manual?
Questions and answers