Table of Contents
Advertisement
Quick Links
A S S E M B LY I N S T R U C T I O N S
Round Lamp Post
Please read through before starting assembly.
Check Box for These Contents
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346
(Mon. to Fri.8:00 AM to 4:00 PM EST) or UK Tel:(44) 2038 687160 - (Mon. to Fri. 1:00 PM to 10:00 PM GMT).
1. Lamp Post Adapter (1)
- xxxxx
2. Post Top Trim (1)
- xxxxx
3. Post (1)
- 6" (15.2cm) Diameter x 72" (183 cm) - xxxxx
4. Post Trim (1)
- xxxxx
5. Post Bottom Trim (1)
- xxxxx
6. 5/8" (16mm) Self-Tapping Screw (4)
7. Tube of Vinyl Weld (1)
- 20000
Tools You Will Need
• Level
Purchased Separately
• Lamp Fixture
• 4x4 (10x10cm) Pressure Treated Post - 8' (244cm) Long (1)
General Information
• Read Instructions through carefully before beginning assembly.
• When handling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 10'x 8' (3m x 2.4m) for unobstructed handling.
Important Note:
• Please refer to local codes before installing outdoor lighting. UF-rated cable should be used for underground
wiring and all materials should be approved by the Underwriter's Laborator (UL). New England Arbors
assumes no liability for errors, ommissionsm or the outcome of any project.
- 20016
1 1/2 in (3.8 cm)
Ø3 in (7.6 cm)
Ø6 in (15.2 cm)
72 1/4 in
(183.5 cm)
6
www.newenglandarbors.com
www.newenglandarbors.co.uk
1
2
3
4
7
5
Ver 1.0/032818
1
Advertisement
Table of Contents
Related Manuals for New England Arbors VA94437
Summary of Contents for New England Arbors VA94437
-
Page 1: General Information
Important Note: • Please refer to local codes before installing outdoor lighting. UF-rated cable should be used for underground wiring and all materials should be approved by the Underwriter’s Laborator (UL). New England Arbors Ver 1.0/032818 assumes no liability for errors, ommissionsm or the outcome of any project. - Page 2 S T E P O N E Wood Post Installation www.newenglandarbors.com www.newenglandarbors.co.uk Determine the location of the post and excavate a 36” (91 cm) Deep x 8” (20 cm) Diameter hole. Ø8 in (20 cm) Insert the wooden post and set the post in place using a bag of concrete. While the concrete is still wet, make sure the wooden post is plumb in both directions and support it in position until the concrete hardens.
- Page 3 S T E P T W O If the light fixture will be hard-wired, continue reading. www.newenglandarbors.com If the light fixture will not be hard-wired (i.e. solar powered), disregard www.newenglandarbors.co.uk this step. With the post on its side, run a length of cable along the outer pocket of the extrusion as shown.
- Page 4 S T E P T H R E E Lamp Post Installation www.newenglandarbors.com www.newenglandarbors.co.uk With a helper and a step ladder, place the round post over the wooden post as shown. Please note that the pre-drilled hole end should be facing up. Apply a small bead of glue around the base of the post as shown (Approximately 4”...
- Page 5 S T E P F O U R Slide the post trim followed by the post top trim as shown. Let the two trims slide down for now as they will be glued in place in later steps. Attach the lamp post adapter onto the top of the post and fasten Apply a small amount of glue to the inside of the top trim where in place with 4 screws as shown.
- Page 6 S T E P F I V E Apply a small amount of glue to the outside of the post where you would www.newenglandarbors.com like your post trim to be located (shown is 3” (7.6 cm)) www.newenglandarbors.co.uk Slide the post trim in place and hold for 20 seconds. To install the light fixture, follow the instructions provided with the unit.
Need help?
Do you have a question about the VA94437 and is the answer not in the manual?
Questions and answers