Table of Contents 1 General Safety Information: ..............................3 2 Set up and operate your T100-S Mobile Mist™ Spray Tan System:................5 3 Prepare the T6000 Mist Applicator™ ..........................6 4 Adjusting the Mist Applicator™ ............................8 5 Misting™ ..................................... 9 6 Maintenance ....................................
General Safety Information: Read all instructions and safety precautions before operating the unit. THIS INDICATES A CONDITION THAT WILL CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS IGNORED. THIS INDICATES A CONDITION THAT COULD CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS IGNORED.
Page 4
GROUNDING INSTRUCTIONS This product must be properly grounded. In the event of an electrical short circuit, grounding reduces the risk of electrical shock by providing an alternate path for the electrical current. This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet that is properly installed and grounded in accordance with local codes and ordinances.
Set up and operate your T100-S Mobile Mist™ Spray Tan System: Separate the middle section of the Mobile Mist case by releasing the three latches. You will find the air hose. Remove the air hose. Close the middle section by securing the three latches. Open the top section by releasing the single latch.
Prepare the T6000 Mist Applicator™ 1. The Mist Applicator Diagram...
Page 7
1. Follow the diagram to prepare the Mist Applicator™ a. Unscrew the plastic cup from the Mist Applicator™. Pour tanning solution into the cup. Do not fill more than ¾ full. b. Carefully screw the cup back onto the main body of the Mist Applicator™. Screw the cup on firmly but DO NOT over tighten.
Adjusting the Mist Applicator™ a. Locate the Solution Flow Screw (#10) on the T6000 diagram. b. Turning the Solution Flow Screw clockwise reduces and will eventually stop the flow of solution. c. Turning the Solution Flow Screw anti or counter clockwise will increase the flow of solution. d.
Misting™ a. You are now ready to begin. You MobileMist™ motor unit is equipped with our new variable speed control. When you turn the motor on it will start at high speed. To lower the speed of the motor and make the unit quieter, simply rotate the knob clockwise to the desired speed.
Maintenance Mobile-Mist™ Turbo Unit. a. The only maintenance necessary on the turbo unit is cleaning and/or changing the filter element. The filter should be removed and rinsed out at least once daily or at least every 4 tanning sessions. The filter housing and filter are located on the side of the Mobile Mist™...
Page 11
threads and dry. Add a small amount of Mist Applicator™ lube to the threads. i. Remove the Air Cap (#2). Rinse under warm running water. Wipe, clean and dry. j. If necessary, remove Air Distributor Plate (#5). Rinse under warm running water. Wipe clean, dry and lubricate with Mist Applicator™...
Troubleshooting a. Mobile Mist™ Turbo unit turned ON. Air blows out of T6000 Mist Applicator™ b. This is correct. Air blows constantly when Turbo unit is ON. c. Mobile Mist™ Turbo unit turned ON. Unit does not operate or blow air? d.
Page 13
For all other technical questions please call your local distributor or Apollo Sprayers Inc. for technical support. Technical Support: Available Monday-Friday, 8am-4:30pm, PST. Apollo Sprayers International, Inc. 1030 Joshua Way Vista, CA 92081 Voice: 760-727-8300 Toll Free: 888- 900-4857 Fax: 760-727-9325 Email: apollo@hvlp.com...
Need help?
Do you have a question about the MOBILE MIST T100-S and is the answer not in the manual?
Questions and answers