Advertisement
Quick Links
Advertisement
Related Manuals for SEI Advisor A106
Summary of Contents for SEI Advisor A106
- Page 1 SEI ADVISOR MODEL A106 OPERATING MANUAL...
-
Page 2: Specifications
SPECIFICATIONS Encoder Capacity 250 calls - paging or DTMF sequences Formats 2 Tone Sequential 1 sec. first tone, 3 sec. second tone Optional high low alert tone DTMF Sequences Standard and Knox F1 3-8 digit sequences Digit duration of 100ms Gap between digits of 100ms Stacks 40 stacks of 20 pages each Frequency... - Page 3 General Specifications Power 12 – 15 VDC Requirements Power < 1 Watt Consumption Current 45 ma normally Draw 100 ma during paging Operating -20C to +70C Temperature Size W 3.25” D 6” H 1.6” Weight .5 lbs FEATURES -250 CALL CAPACITY ENCODER -EASY TO PROGRAM -TWO TONE PAGING 1 sec.
-
Page 4: Back View
INSTALLATION BACK VIEW RJ45 CABLE 1 PTT RELAY CONTACT TO GND 2 TX AUDIO OUT BLU SEE NOTE 3 RX AUDIO IN SQUELCHED AUDIO 4 TX AUDIO IN MIC AUDIO 5 POWER 12 - 15VDC 6 GROUND 7 RELAY CLOSURE WITH 8 RELAY DECODE NOTE: TX AUDIO OUT IS BEST CONNECTED TO A FLAT AUDIO INPUT. - Page 5 PROGRAMMING - HOLD THE “#” BUTTON DOWN FOR 5 SECONDS - GOES INTO PROGRAM MODE - PRESSING THE “#” BUTTON WILL STEP THROUGH THE PROGRAMMING OPTIONS PRESS THE * TO SELECT THE OPTION - PROG ENCODER SEE PAGE 7 ENTERS TWO TONE ENCODER PROGRAM MODE - PROG DTMF SEE PAGE 9 ENTERS DTMF SEQUENCE PROGRAM MODE - PROG DECODER SEE PAGE 10...
- Page 6 PROGRAMMING ENCODER - HOLD THE “#” BUTTON DOWN FOR 5 SECONDS - GOES INTO PROGRAM MODE - SELECT PROG ENCODER “*” - ENTER THE SLOT NUMBER TO BE PROGRAMMED (1 TO 250) - SEE THE LIST OF MOTOROLA AND PLECTRON TONES IN MEMORY ON PAGE 8 (CUSTOM TONES CAN ALSO BE ADDED ) - ENTER TONE A (ENTER ALL THE DIGITS INCLUDING THE DIGIT AFTER THE DECIMAL POINT ex.
- Page 7 STANDARD TONES IN MEMORY MOTOROLA 288.5 MOTOROLA 1122.5 PLECTRON 643.0 MOTOROLA 296.5 MOTOROLA 1153.4 PLECTRON 672.0 MOTOROLA 304.7 MOTOROLA 1185.2 PLECTRON 701.0 MOTOROLA 313.0 MOTOROLA 1217.8 PLECTRON 732.0 MOTOROLA 321.7 MOTOROLA 1251.4 PLECTRON 765.0 MOTOROLA 330.5 MOTOROLA 1285.8 PLECTRON 799.0 MOTOROLA 339.6 MOTOROLA...
- Page 8 PROGRAMMING DTMF SEQUENCES - HOLD THE “#” BUTTON DOWN FOR 5 SECONDS - GOES INTO PROGRAM MODE - SELECT PROG DTMF - ENTER THE SLOT NUMBER TO BE PROGRAMMED (1 TO 250) - ENTER NUMBER OF DIGITS 3-8 - ENTER 1 FOR STANDARD OR 2 FOR KNOX F1 - ENTER 1ST DIGIT AND PRESS “#”...
- Page 9 PROGRAMMING DECODER - HOLD THE # BUTTON DOWN FOR 5 SECONDS - GOES INTO PROGRAM MODE - SELECT PROG DECODER - ENTER DECODER SLOT NUMBER 1 -17 OR 1-20 WHEN USING INTERFACE UNIT (SEE THE DECODER SLOT CHART ON THE PREV. PAGE) - HOW THE UNIT RESPONDS TO A DECODE DEPENDS ON THE SLOT THE TONES ARE PROGRAMMED INTO.
- Page 10 DELAY ADD/DEL IF THE RADIO USES A PTT ID WHEN IT IS KEYED THEN A DELAY MUST BE ADDED SO THE TONES WILL TRANSMIT AFTER THE ID IS DONE. HOLD THE “#” IN FOR 5 SECONDS TO EXIT OR PROCEED TO NEXT OPTION DE-EMPH ADD/DEL FOR DE-EMPHASIS OF AUDIO OUTPUT.
- Page 11 STEP 4 ENTER THE CODE FOR ENCODE DIVIDE THE TONE BY 1.436 AND ENTER THE RESULT. MUST ENTER 4 DIGITS. 288.5 / 1.436 = 200.91 ROUND TO 0201 AND ENTER 1130.0 / 1.436.= 786.91 ROUND TO 0787 AND ENTER HOLD THE “#” IN FOR 5 SECONDS TO EXIT OR PROCEED TO NEXT OPTION CLR MEMORY? YOU ARE GIVEN THE CHOICES OF: CLEARING THE ENCODER MEMORY...
- Page 14 SLOT TONE 1 TONE 2 NAME (or DTMF digits) ____ ______ ______ ____________________ ____ ______ ______ ____________________ ____ ______ ______ ____________________ ____ ______ ______ ____________________ ____ ______ ______ ____________________ ____ ______ ______ ____________________ ____ ______ ______ ____________________ ____ ______ ______ ____________________ ____ ______ ______...
Need help?
Do you have a question about the Advisor A106 and is the answer not in the manual?
Questions and answers